Skip to the content
2 layers113 × 88.3 mmPlate, the printed circuit board in 3D

Custom keyboard with Choc-spaced 3x5 Corne layout, diodeless, nice!nano compatible, dual-side PCB with support for both hotswap and soldered switches.

Size
113 × 88.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
55
Pads
139
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 8.0 (file 20240108)
Created
2 Sep 2024
Updated
18 Nov 2024

Overview

Plate is an open-source printed circuit board by itsdmd, from the itsdmd/chocowi36 repository on GitHub. It is a 2-layer board of 113 × 88.3 mm with 27 parts on 55 nets.

Its parts include 18 switches and 2 ICs. It belongs with the keyboards and input boards and the nRF52 and nRF5x boards of this library.

README

README.md

chocowi36

A 36-key, low profile, wireless, split keyboard. Derived from davidphilipbarr/Choc-Spaced-Corne, with the original design based on Foostan's Corne.

Finished build

chocowi36 PCB Top - JLCPCB renderchocowi36 PCB Bottom - JLCPCB renderchocowi36 PCB - KiCad render

Changes

  • The PCB shape, dimensions and mounting holes' position are modified to personal preferences.
  • Battery onboard connector is replaced with through hole pads for better flexibility. Power switch is connected to the positive terminal of the battery instead of ground.
  • The outermost thumb key has been changed to a 1u key, and the splayed angle of the thumb cluster has been increased to 15 degrees.
  • Allow the nice!nano to be mounted with the USB port facing down for both halves for better MCB protection.
  • Support both hotswap and soldered switches. Only Choc v1 switches are supported.

Case

The case for the keyboard can be found here: OnShape document

Finished build - Folded

chocowi36 Case - OnShape renderchocowi36 Case Folded - OnShape render

This case features a 5.5x2.1 DC power jack for connecting to a detachable Li-Ion battery enclosure. The provided enclosure is designed for storing a 21700 battery with a protection PCB attached to it. This enclosure can act as a tenting mechanism, or for locking the two keyboard halves in place when folded for travelling. Most parameters can be slightly adjust without breaking the whole thing. The screw holes are 3.0mm in diameter (for housing M2 heat inserts), and default tolerance is 0.3-0.5mm.

Firmware

ZMK shield definition of chocowi36 can be obtained here. Please note that the definition files are written for the keyboard to be used with a third nice!nano as the central/dongle.

The provided files should only act as the boilerplate, please adjust the configurations according to your personal needs and preferences. You can create your own repo using the template and make further modifications.

Notes

There are two versions of the PCB, one with straight traces and one with curved traces. There are no major differences between the two, mostly just aesthetics.

Disclaimer

This is a personal project and not affiliated with the original authors. The gerber file has been checked against JLCPCB's DFM checker and no critical error was found. All files (including firmware) are provided as-is, without any warranty or support.

Parts

27
QtyValueFootprintReferences
18SW_Pushitsdmd:KSC_ChocSW2, SW3, SW4, SW5, SW6, SW10, SW11, SW12, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21 +2
4MountingHoleitsdmd:MountingHole_2.2mm_M2H1, H2, H3, H4
2nice!nanoitsdmd:MCB_nice-nano_flipU1, U2
1Battery_Cellitsdmd:Battery_Pads-dual-sideBT1
1SW_Pushitsdmd:SW-T_7.4x2.6-4pad-smdSW_RST1
1SW_SPDTitsdmd:SW-S_MSK-12C02SW_POWER1

More from itsdmd/chocowi36

1
  • 2 layers113.1 × 88.3 mmChocowi36, the printed circuit board in 3D

    Chocowi36

    itsdmd/chocowi36

    Custom keyboard with Choc-spaced 3x5 Corne layout, diodeless, nice!nano compatible, dual-side PCB with support for both hotswap and soldered switches.

    29 parts5

Similar boards

  • 2 layers47.6 × 27.3 mmMmc usb 1, the printed circuit board in 3D

    Mmc usb 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    27 parts1.2k
  • 2 layers77.4 × 77.4 mmCORAZON LEDS CON FADE, the printed circuit board in 3D

    CORAZON LEDS CON FADE

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    27 parts915
  • 2 layers44.2 × 29.3 mmI2c tiny usb, the printed circuit board in 3D

    I2c tiny usb

    harbaum/I2C-Tiny-USB

    Cheap and simple I²C to USB interface

    27 parts454
  • 2 layers22 × 42 mmNvme bm to e, the printed circuit board in 3D

    Nvme bm to e

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    27 parts253GPL-3.0
  • 2 layers80 × 61 mmPicoProducer, the printed circuit board in 3D

    PicoProducer

    pjgpetecodes/pico-streamdeck

    This project is an OBS Controller using a Raspberry Pi Pico and CircuitPython.

    27 parts230MIT
  • 2 layers186 × 45 mmAddOnD, the printed circuit board in 3D

    AddOnD

    freeDSP/freeDSP-aurora

    freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth

    27 parts226CC-BY-SA-4.0
  • 2 layers29.6 × 40.6 mmDbwifi revB, the printed circuit board in 3D

    Dbwifi revB

    ugcs/ddc

    Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.

    27 parts223

Questions

How big is the Plate PCB?

It measures 113 × 88.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Plate use?

27 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Plate KiCad files?

From the itsdmd/chocowi36 repository on GitHub, at the commit this page was made from: the board is plate/plate.kicad_pcb and its schematic pcb/chocowi36-plate.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Plate design in my own project?

Its repository states no licence, so its author keeps all rights: ask itsdmd before reusing the design.