
Tx module
koushik12328/Smart_mining_helmet
An ESP32-powered safety helmet featuring gas detection, impact sensing, and IoT connectivity

A mobile application for fireforce helemt
Helmeto is an open-source printed circuit board by irfan5122, from the irfan5122/Helmeto repository on GitHub. It is a 2-layer board of 80 × 60 mm with 26 parts on 10 nets.
It is built around the ESP32-WROOM-32, BMP280 and MQ-4, with the AMS1117-3.3 among its other parts. Its parts include 8 connectors, 6 resistors, 5 capacitors, 2 ICs and 1 diode. It belongs with the ESP32 boards of this library.
Custom PCB for the Helmeto smart helmet sensor system. ESP32-WROOM-32 based board with gas sensors, environmental sensing, and BLE connectivity.
| Ref | Component | Value | Purpose |
|---|---|---|---|
| U1 | ESP32-WROOM-32 | — | MCU + BLE radio |
| U2 | AMS1117-3.3 | 3.3V LDO | Voltage regulator |
| J1 | USB-C Header | 4-pin | Power input (5V) |
| J2 | MQ-7 Header | 4-pin | CO sensor (GPIO34 analog, GPIO26 digital) |
| J3 | MQ-4 Header | 4-pin | CH4 sensor (GPIO35 analog, GPIO25 digital) |
| J4 | BMP280 Header | 6-pin | Temp/Pressure (I2C: SDA=GPIO21, SCL=GPIO22) |
| J5 | ME2-O2 Header | 3-pin | Future oxygen sensor expansion |
| J6 | I2C Expansion | 4-pin | Future I2C sensor (SDA, SCL, 3.3V, GND) |
| J7 | Analog Expansion | 4-pin | Future analog sensor (GPIO32, GPIO33, 5V, GND) |
| J8 | SPI/UART Expansion | 6-pin | Future digital sensor (GPIO16-19, 3.3V, GND) |
| R1,R2 | Load Resistors | 10kΩ | MQ sensor voltage dividers |
| R3,R4 | I2C Pull-ups | 4.7kΩ | SDA/SCL pull-up resistors |
| R5 | LED Resistor | 1kΩ | Power indicator current limit |
| R6 | EN Pull-up | 10kΩ | ESP32 enable pin pull-up |
| C1,C2 | Bulk Caps | 10µF | Regulator input/output |
| C3,C4,C5 | Bypass Caps | 100nF | IC decoupling |
| D1 | Power LED | Green | Power indicator |
| GPIO | Function | Sensor |
|---|---|---|
| 34 | Analog input | MQ-7 (CO) A0 |
| 26 | Digital input | MQ-7 (CO) D0 |
| 35 | Analog input | MQ-4 (CH4) A0 |
| 25 | Digital input | MQ-4 (CH4) D0 |
| 21 | I2C SDA | BMP280 + I2C expansion |
| 22 | I2C SCL | BMP280 + I2C expansion |
| 32 | Analog (expansion) | Analog expansion header |
| 33 | Analog (expansion) | Analog expansion header |
| 16 | Digital (expansion) | SPI/UART expansion |
| 17 | Digital (expansion) | SPI/UART expansion |
| 18 | Digital (expansion) | SPI/UART expansion |
| 19 | Digital (expansion) | SPI/UART expansion |
| Pin | Signal | Notes |
|---|---|---|
| 1 | O2_WE | Working electrode output |
| 2 | O2_CE | Counter electrode |
| 3 | GND | Ground reference |
Use with a transimpedance amplifier circuit (e.g., LMP91000) between the sensor and an ESP32 ADC pin.
SDA, SCL, 3.3V, GND — for any I2C sensor (BME680, SHT30, etc.)
GPIO32, GPIO33, 5V, GND — for analog sensors on the remaining ADC channels
GPIO16, GPIO17, GPIO18, GPIO19, 3.3V, GND — for SPI or UART sensors
helmeto.kicad_pro| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100nF | Capacitor_SMD:C_0805_2012Metric | C3, C4, C5 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R6 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 4.7k | Resistor_SMD:R_0805_2012Metric | R3, R4 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ANALOG_EXP | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J7 |
| 1 | BMP280 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | I2C_EXP | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J6 |
| 1 | ME2-O2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | MQ-4 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | MQ-7 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | PWR_LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | SPI_UART_EXP | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J8 |
| 1 | USB-C | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |

koushik12328/Smart_mining_helmet
An ESP32-powered safety helmet featuring gas detection, impact sensing, and IoT connectivity


cs99x/GasMonitorLoRaCloud
This project is a mobile and embedded application for a university course called "Mobile and Embedded Development".


rmingon/Falcon-Edge
A 3D-printable flying-wing airframe with a custom ESP32 flight computer—open hardware you can solder, screw together, and fly.



fredszaq/crossometer-mini
Design files for crossometer-mini device
It measures 80 × 60 mm and has 2 copper layers, 1.6 mm thick.
26 parts, built around the ESP32-WROOM-32, BMP280, MQ-4 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the irfan5122/Helmeto repository on GitHub, at the commit this page was made from: the board is PCB/helmeto.kicad_pcb and its schematic PCB/helmeto.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask irfan5122 before reusing the design.