6 layers40.2 × 40.2 mm
6 layers45 × 45 mm
Panel rp2350 20x20 temp
iorodeo/panels_g4_single_pcb1G4 Panels single PCB designs
- Size
- 45 × 45 mm
- Copper layers
- 6
- Thickness
- 1.6 mm
- Parts
- 556
- Nets
- 138
- Pads
- 1,515
- Tracks, vias
- 4,550, 679
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 2 Oct 2023
- Updated
- 24 Nov 2025
Overview
Panel rp2350 20x20 temp is an open-source printed circuit board by iorodeo, from the iorodeo/panels_g4_single_pcb repository on GitHub, published under the CC-BY-4.0 licence. It is a 6-layer board of 45 × 45 mm with 556 parts on 138 nets, routed with 4,550 tracks and 679 vias.
It is built around the UCC27517DBV, AP2112K-3.3 and APS6404L-3SQR-SN, with the ABM8-272-T3 among its other parts. Its parts include 400 diodes, 76 capacitors, 43 ICs, 28 resistors and 5 connectors. It belongs with the RP2350 boards of this library.
Main components
4
UCC27517DBV
SOT-23-5-40℃~+140℃ 1 1V~1.2V 2.2V~2.4V 4.5V~18V 4A 4A 7ns 8ns IGBT、MOSFET Low Side Under Voltage Protection SOT-23-5 Gate Drivers ROHSTexas InstrumentsGate DriversAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
APS6404L-3SQR-SN
SOP-8SOP-8 PSRAM ROHSAP MemoryDRAM
ABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystals
README
README.mdpanels_g4_single_pcb
Prototype designs for a single PCB G4 panels variant.
Parts
556| Qty | Value | Footprint | References |
|---|---|---|---|
| 399 | LED | panel_custom:LED_0402_1005Metric | D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112, D113 +383 |
| 52 | 100nF | Capacitor_SMD:C_0201_0603Metric | C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25 +36 |
| 40 | UCC27517 | Package_TO_SOT_SMD:SOT-23-5 | U10, U11, U12, U13, U14, U15, U16, U17, U18, U19, U20, U21, U22, U23, U24, U25 +24 |
| 20 | 270 | Resistor_SMD:R_0201_0603Metric | R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23, R24, R25 +4 |
| 18 | 10uF | Capacitor_SMD:C_0402_1005Metric | C59, C60, C61, C62, C63, C64, C65, C66, C67, C68, C69, C70, C71, C72, C73, C74 +2 |
| 3 | 1k | Resistor_SMD:R_0201_0603Metric | R2, R3, R5 |
| 2 | 10k | Resistor_SMD:R_0201_0603Metric | R1, R4 |
| 2 | 15pF | Capacitor_SMD:C_0201_0603Metric | C1, C2 |
| 2 | 27 | Resistor_SMD:R_0201_0603Metric | R7, R8 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C7, C8 |
| 2 | 4.7uF | RP2350_80QFN_minimal:C_0402_1005Metric_small_pads | C4, C5 |
| 2 | Conn_01x05 | panel_custom:ConnRcpt_1x5_SMH-105-02-X-S | J4, J5 |
| 2 | Conn_01x05 | panel_custom:PinHeader_1x5_M20-8890545R | J2, J3 |
| 2 | SW_Push | panel_custom:TS-1088-AR02016 | SW1, SW2 |
| 1 | 3.3uH | RP2350_80QFN_minimal:L_pol_2016 | L1 |
| 1 | 33 | Resistor_SMD:R_0201_0603Metric | R6 |
| 1 | ABM8-272-T3 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U43 |
| 1 | APS6404L-3SQR | panel_custom:flashmem_PSON50P300X200X60-9N | U1 |
| 1 | Conn_01x04 | panel_custom:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | J1 |
| 1 | LED_T0 | panel_custom:LED_0402_1005Metric | D1 |
| 1 | RP2354B_80QFN | RP2350_80QFN_minimal:RP2350-QFN-80-1EP_10x10_P0.4mm_EP3.4x3.4mm_ThermalVias | U2 |
More from iorodeo/panels_g4_single_pcb
4- 6 layers40.2 × 40.2 mm
- 6 layers40.2 × 40.2 mm
- 6 layers40.4 × 40.4 mm
Similar boards
- 4 layers62.8 × 61.7 mm
- 4 layers132.8 × 75.8 mm
AudioPicoBare
elrir01/AudioPico
This board receive audio from a BT source like a phone and outputs via a DAC the audio. It's an old project of mine but I've decided to publish it just now, so the full description is not ready and will be updated in…
84 partsGPL-3.0 - 6 layers80 × 60 mm
Ice core
enkhbold470/ice-core
iCE40UP5K FPGA board with 8 MB PSRAM and three Pmods, programmed over USB-C by an RP2040. 6-layer KiCad 10 board.
78 partsCERN-OHL-S-2.0 - 4 layers70 × 97 mm
- 4 layers21 × 51 mm
Metalclaw pico rp2
renzbagaporo/metalclaw-pico-rp2
An RP2354B board for testing firmware on a Raspberry Pi Pico or Pico 2. Metalclaw firmware provides Python-controlled peripheral emulation and a USB debug probe.
132 partsCC-BY-SA-4.0 - 4 layers30 × 30 mm
PCIe Pie
vk-sahni/M.2_IMU_sensor_module
KiCad design for an M.2 Key A RP2350B sensor module featuring an MPU-9250 IMU and BME280, intended for UAV and ArduPilot integration experiments.
85 parts - 2 layers30.5 × 68.6 mm
- 2 layers120 × 90 mm
Questions
How big is the Panel rp2350 20x20 temp PCB?
It measures 45 × 45 mm and has 6 copper layers, 1.6 mm thick.
What parts does the Panel rp2350 20x20 temp use?
556 parts, built around the UCC27517DBV, AP2112K-3.3, APS6404L-3SQR-SN and ABM8-272-T3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Panel rp2350 20x20 temp KiCad files?
From the iorodeo/panels_g4_single_pcb repository on GitHub, at the commit this page was made from: the board is panel_rp2350_20x20/temp_route/panel_rp2350_20x20_temp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Panel rp2350 20x20 temp design in my own project?
Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).