Skip to the content
2 layers99.7 × 78.7 mmA2ext carrier, the printed circuit board in 3D

A2ext carrier

iolo/a2ext

General purpose Apple II Extension Card using RP2350B

Size
99.7 × 78.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
72
Pads
149
Tracks, vias
362, 24
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
17 Sep 2026
Updated
12 Oct 2026

Overview

A2ext carrier is an open-source printed circuit board by iolo, from the iolo/a2ext repository on GitHub. It is a 2-layer board of 99.7 × 78.7 mm with 14 parts on 72 nets, routed with 362 tracks and 24 vias.

Its parts include 3 capacitors, 2 connectors, 2 fuses, 1 resistor and 1 diode. It belongs with the RP2350 boards of this library.

README

hw/a2ext-dvi/README.md

a2ext-dvi

Revision 0.3 uses A4 landscape with enlarged text: 1.524 mm pin names, wire labels and values, 1.27 mm pin numbers, and 1.778 mm references/notes. The revised layout preserves all electrical connections.

Passive DVI video daughterboard using an HDMI Type A connector and the PRD's 270 ohm series resistor network. Open the KiCad 10 project; symbols are local. The SH pin represents all four plated shell contacts. The physical PCB selects Kycon KDMIX-SL1-NS-WS-B15 for PCB-P2-THT. All 19 signal contacts and four shell tabs are through-hole. This upright right-angle port exits the right board edge; its approximately 16.4 mm body height and panel opening require a new fit check. The PCB-P1 Molex connector cannot fit this revision.

The 45 x 45 mm two-layer board uses axial 1/4 W DIN0207 270 ohm resistors (7.62 mm formed pitch), a 5.0 mm pitch radial ceramic capacitor, and a bottom-mounted 2x10 female socket at J1. H1/H2 are 2.7 mm spacer holes aligned with the carrier. Resistor-to-HDMI pairs use a single layer per pair without vias: D0/D1 on F.Cu and D2/clock on B.Cu. Output tuning keeps intra-pair trace-length difference below 0.020 mm. Full routed lengths are in validation/summary.json; the carrier and IDC-to-resistor segments are not pair-length tuned. Controlled impedance and physical signal quality are unqualified. See fabrication notes, Gerbers and drills, top, bottom, and assembly plots. DRC, ERC, and schematic parity reports in validation/ have zero findings. No SMD assembly or solder stencil is required. All four shell tabs require plated slots; retain both drill files when ordering. tmds-routing.json preserves the reviewed pair tracks during regeneration; the placement generator locks them before routing the other nets.

LanePositive GPIO / IDCNegative GPIO / IDCHDMI contacts
D036 / 437 / 57 / 9
D138 / 639 / 74 / 6
D240 / 841 / 91 / 3
Clock42 / 1043 / 1110 / 12

Each conductor has a 270 ohm, 1% resistor. Shields, pin 17, shell, and both IDC ground contacts share GND. Pin 18 receives the carrier's fused +5V_DB supply; there is no additional series diode drop on this board. C1 decouples that rail. UART, RUN, 3.3 V power, GPIO35/44-47, DDC, HPD, CEC, and utility are unused.

The bundled libdvi program uses the lower GPIO for the positive conductor when invert_diffpairs=false. Use PIO1 base 16 and 64-bit mask helpers. Its clock generator uses the shared PWM slice for even/odd GPIO42/43. This is the reference's resistor-driven signaling approach, not a claim of HDMI compliance.

Initially use direct carrier mating. No ribbon cable length is qualified. Validate a fixed 640x480 timing mode, pair polarity, eye/edge quality, connector +5 V, and lock on multiple monitors with a real board. No EDID negotiation or hotplug handling is implemented by this schematic. Carrier power comes from the slot input (or an off-host fixture at that input); USB is data only.

Validation so far: ERC and named-net export checks. Firmware and physical TMDS tests are pending. From the repository root:

sh
python3 tools/schematics.py dvi
python3 tools/check_schematics.py a2ext-dvi

References: ref/A2DVI v5.x hardware and ref/A2DVI-Firmware/libraries/libdvi/dvi_serialiser.{c,pio}.

Parts

14
QtyValueFootprintReferences
3MountingHole_2.7mm_M2.5MountingHole_2.7mm_M2.5H1, H2, H3
210uFA2Ext:C_Radial_5C9, C10
1100mA PTCA2Ext:PTC_MF_R010F2
1100nFA2Ext:C_Radial_5C8
110kA2Ext:R_Axial_7.62R4
11N5819A2Ext:Schottky_DO41D1
1500mA PTCA2Ext:PTC_MF_R050F1
1Apple II slot, counter-clockwise numberingA2Ext:AppleII_Edge50J1
1Daughterboard IDC20A2Ext:IDC20J2
1SYNC: OPEN except verified slot 7A2Ext:SYNCJP1
1WeAct RP2350B V1.0 (prepared module)A2Ext:WeAct_RP2350B_V1M1

More from iolo/a2ext

2
  • 2 layers45 × 45 mmA2ext vga, the printed circuit board in 3D

    A2ext vga

    iolo/a2ext

    General purpose Apple II Extension Card using RP2350B

    15 parts
  • 2 layers45 × 45 mmA2ext dvi, the printed circuit board in 3D

    A2ext dvi

    iolo/a2ext

    General purpose Apple II Extension Card using RP2350B

    13 parts

Similar boards

  • 2 layers116.8 × 30 mmType d, the printed circuit board in 3D

    Type d

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    14 parts3kApache-2.0
  • 2 layers32 × 22 mmDiff driver, the printed circuit board in 3D

    Diff driver

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    14 parts990GPL-3.0
  • 2 layers34 × 45 mm2032Charger, the printed circuit board in 3D

    2032Charger

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    14 parts915
  • 2 layers34 × 109.9 mmTdisplay s3, the printed circuit board in 3D

    Tdisplay s3

    landonr/homeThing

    Wifi Smart Home Remotes that run on ESPHome

    14 parts551GPL-3.0
  • 2 layers45.3 × 42.7 mmMainPcb, the printed circuit board in 3D

    MainPcb

    adamb314/ServoProject

    Getting the most out of your hobby servo

    14 parts545
  • 2 layers42.5 × 28.8 mmC5VRX JACK DIY, the printed circuit board in 3D

    C5VRX JACK DIY

    Twotoz/C5VRX

    Ultra-minimal, zero-CPU 5.8 GHz analog FPV video receiver using ESP32-C5 Wi-Fi 6 PHY MODEM_DIAG, BitScrambler WBFM demodulation & resistor DAC CVBS

    14 parts515GPL-3.0
  • 2 layers62 × 24 mmMai button, the printed circuit board in 3D

    Mai button

    whowechina/mai_pico

    Pico controller for Maimai

    14 parts475

Questions

How big is the A2ext carrier PCB?

It measures 99.7 × 78.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the A2ext carrier use?

14 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the A2ext carrier KiCad files?

From the iolo/a2ext repository on GitHub, at the commit this page was made from: the board is hw/a2ext-carrier/a2ext-carrier.kicad_pcb and its schematic hw/a2ext-carrier/a2ext-carrier.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the A2ext carrier design in my own project?

Its repository states no licence, so its author keeps all rights: ask iolo before reusing the design.