4 layers100 × 100 mm
FC Board v3
proveskit/flight_controller_board
The main flight computer board for the PROVES Kit.
98 parts6CERN-OHL-W-2.0
4 layers100 × 100 mm
Payload board
inspireFly-VT/ContentCube_Payload_Board2The payload board for inspireFly's ContentCube satellite.
- Size
- 100 × 100 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 98
- Nets
- 87
- Pads
- 329
- Tracks, vias
- 828, 100
- Pours
- 13
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Oct 2024
- Updated
- 18 Feb 2025
Overview
Payload board is an open-source printed circuit board by inspireFly-VT, from the inspireFly-VT/ContentCube_Payload_Board repository on GitHub. It is a 4-layer board of 100 × 100 mm with 98 parts on 87 nets, routed with 828 tracks and 100 vias.
It is built around the TLV61046ADBV, AZ1117CH-3.3TRG1 and MAX706RESA, with the NSR0320MW2 and ABLS-12.000MHZ-B2-T among its other parts. Its parts include 24 capacitors, 18 resistors, 12 connectors, 8 ICs and 6 diodes. It belongs with the RP2040 boards of this library.
Main components
5
TLV61046ADBV
SOT-23-6-40℃~+125℃@(TJ) 1 1.05MHz 1.8V~5.5V 110uA 3.3V~28V Adjustable Boost Boost Built-in No Overcurrent Protection、Light load efficient mode、Load disconnect SOT-23-6 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
AZ1117CH-3.3TRG1
SOT-223-20℃~+125℃@(Tj) 0.003%Vout 1 1.2V@(800mA) 1.35A 10V 3.3V 4mA 70dB@(120Hz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
MAX706RESA
SOIC-8-40℃~+85℃@(TA) 1 140ms 2.63V Active Low Power Supervisor Push-pull SOIC-8 Supervisor and Reset ICsMaxim Integrated (Analog Devices)Supervisor And Reset ICs
NSR0320MW2
SOD-323-55℃~+125℃ 1 Independent 1A 20V 500mV@900mA 50uA@15V 5A SOD-323 Schottky Diodes ROHSonsemiSchottky Diodes
ABLS-12.000MHZ-B2-T
HC-49S-SMD-20℃~+70℃ 12MHz 18pF 50Ω Crystal Oscillator ±20ppm ±50ppm HC-49S-SMD Crystals ROHSAbraconCrystals
README
README.mdView this project on CADLAB.io.
ContentCube_Payload_Board
The payload board for inspireFly's ContentCube satellite.
Parts
98| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | TESTPOINTROUND1.5MMNO | TestPoint:TestPoint_Pad_D1.0mm | T1V2, T3V3, T13V, TCAM3V3, TCGND1, TDGND1, TF3V3, TFGND1, TGND1, TGND3, TREG3V3, TUCS1 |
| 10 | 0.1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C4, C5, C7, C8, C9, C10, C11, C15, C16, C17 |
| 3 | , , | ||
| 3 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1, R3, R8 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6, C14, C19 |
| 3 | LED | LED_SMD:LED_0805_2012Metric | D2, D3, D4 |
| 3 | NSR0320 | Diode_SMD:D_SOD-323 | D1, D5, D7 |
| 2 | SolarPanelBoards:MountingHoles | J2, J5 | |
| 2 | 0.065 | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R13, R14 |
| 2 | 1.0uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C22, C23 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C18, C24 |
| 2 | 10uF/16V | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C20, C21 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R7 |
| 2 | 220 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R10, R12 |
| 2 | 27.4 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5, R6 |
| 2 | 27pF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C2 |
| 2 | 300k | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | R15, R16 |
| 2 | INA180A3 | Package_TO_SOT_SMD:SOT-23-5 | U3, U4 |
| 2 | KMR2 | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW1, SW2 |
| 1 | 10uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C12 |
| 1 | 10uH/1A | Inductor_SMD:L_1008_2520Metric_Pad1.43x2.20mm_HandSolder | L1 |
| 1 | 16k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R20 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R21 |
| 1 | 22uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C13 |
| 1 | 4.7uF | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | C26 |
| 1 | 470 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11 |
| 1 | 50 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R19 |
| 1 | 503398-1892 | PayloadBoard:MOLEX_503398-1892 | J10 |
| 1 | ABLS-12.000MHZ-B2-T | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | AZ1117CH-3.3TRG1 | PayloadBoard:SOT230P700X180-4N | IC2 |
| 1 | Antenna_Conn | PayloadBoard:Molex_Pico_CON_5040500491 | J3 |
| 1 | Breakout | PayloadBoard:Molex_Pico_CON_5040500691 | J6 |
| 1 | Cam_Conn | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Cam_PicoLock | PayloadBoard:Molex_Pico_CON_5040500691 | J1 |
| 1 | DNF | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 1 | FC Breakout | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J12 |
| 1 | FC to EPS Connector | Picolock2Pos:MOLEX_504050-0291 | J8 |
| 1 | LOGO | PayloadBoard:vtlogo | G*** |
| 1 | LOGO | PayloadBoard:blackjack | G*** |
| 1 | LOGO | PayloadBoard:odds | G*** |
| 1 | LOGO | PayloadBoard:longIFlogo35x25mm | G*** |
| 1 | LOGO | PayloadBoard:amplab | G*** |
| 1 | LOGO | LOGO | G*** |
| 1 | LOGO | PayloadBoard:balloon | G*** |
| 1 | LOGO | PayloadBoard:makingspace | G*** |
| 1 | MAX706RESA | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | Molex_Micro_USB | PayloadBoard:MOLEX_105164-0001 | J7 |
| 1 | Q_PMOS_GSD | Package_TO_SOT_SMD:SC-59 | Q1 |
| 1 | RP2040_QFN56 | PayloadBoard:custom_IC57_RP2040 | IC1 |
| 1 | SWC | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J15 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | TLV61046ADB | Package_TO_SOT_SMD:SOT-23-6 | U7 |
| 1 | W25Q128JVPIQ TR | Package_DFN_QFN:WDFN-8-1EP_6x5mm_P1.27mm_EP3.4x4mm | U1 |
| 1 | usb jumper | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | J4 |
| 1 | ~ | PayloadBoard:CON30_1X30_DRB_XF2C_TYC | U6 |
The 97 most common of 98 parts.
Similar boards
- 4 layers88 × 94.5 mm
Flight computer dev board rfm98pw
proveskit/development_boards
Miscellaneous dev boards to test the components of the PROVES Kit on a smaller scale.
103 parts1 - 6 layers150 × 87 mm
POWERCORE V2.0 MOTHERBOARD
Rack-Robotics/Powercore-V2.0
Open-Source wire EDM power supply by Rack Robotics, Inc.
254 parts258 - 4 layers135.2 × 97.6 mm
- 4 layers90.2 × 95.9 mm
- 4 layers90.2 × 95.9 mm
Mainboard v05
alxklso/ISP-cubesat
This is the repo for the Isomer Space Program (ISP) 1U CoyoteSat CubeSat mission.
255 parts1MIT - 4 layers90.2 × 95.9 mm
PowerDistribution
UChicago-Space-Program/pulse-hardware
This is the central repository for documents related to PULSE-A hardware development.
188 parts1 - 4 layers90.2 × 95.9 mm
Mainboard v06b samwise
pete4radio/SAMWISE-1-1-HW-Training
PCBs fabbed in May 2024 for SAMWISE
204 parts
Questions
How big is the Payload board PCB?
It measures 100 × 100 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Payload board use?
98 parts, built around the TLV61046ADBV, AZ1117CH-3.3TRG1, MAX706RESA and NSR0320MW2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Payload board KiCad files?
From the inspireFly-VT/ContentCube_Payload_Board repository on GitHub, at the commit this page was made from: the board is payload_board.kicad_pcb and its schematic Documentation/RP2040/rp2040_preset.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Payload board design in my own project?
Its repository states no licence, so its author keeps all rights: ask inspireFly-VT before reusing the design.