Skip to the content
4 layers40 × 35.2 mmFlame lamp led driver, the printed circuit board in 3D

Flame lamp led driver

ikatkov/flame-lamp-led-driver

60A max current. Power supply 5-25V. Based on http://elm-chan.org/works/lchk/report.html

Size
40 × 35.2 mm
Copper layers
4
Thickness
1.6 mm
Parts
26
Nets
15
Pads
61
Tracks, vias
99, 2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
18 Nov 2022
Updated
19 Nov 2022

Overview

Flame lamp led driver is an open-source printed circuit board by ikatkov, from the ikatkov/flame-lamp-led-driver repository on GitHub. It is a 4-layer board of 40 × 35.2 mm with 26 parts on 15 nets, routed with 99 tracks and 2 vias.

It is built around the FR9888SPGTR, LM358 and MBRA340T3G. Its parts include 6 capacitors, 6 resistors, 5 connectors, 2 ICs and 2 diodes. It belongs with the lEDs and displays boards of this library.

Main components

3

README

README.md

(Power) Inductor saturation current tester

~60A max current. Power supply 5-25V. Based on http://elm-chan.org/works/lchk/report.html

You will need an oscilloscope to take measurements.

Theory

Once powered, the capacitor bank charges up. The circuit fires off a variable-width pulse into the MOSFET gate. MOSFET turns ON and short-circuits the inductor to the capacitor power bank. The current starts to rise linearly until the saturation point is reached. Once the inductor is saturated, it behaves like an ohmic piece of wire, and the current increases exponentially until the pulse is over, and the MOSFET is switched OFF. Saturation is a knee, not a sharp point. So you have some wiggle room in what current you designate as a "saturation current." Before the saturation point and including the "knee region," inductance will be higher than labeled. Once saturated sufficiently - inductance will drop.

Commercial manufacturers pick the point where a power inductor loses 20-30% of its labeled inductance. One can safely operate inductors at x1.3-1.5 their knee point.

You take voltage drop measurements across 0.1 Ohm resistor, multiply by 10 and get current in Amps flowing through your inductor under test. I = V*10

You can also compute actual inductance be taking your supply voltage and dividing by the voltage slope. L = Vs * Δt / ΔI.

Practical operations

See "sort-of" instructions video https://www.youtube.com/watch?v=3Y_WcuIenSM Notice that although their PCB is labeled 1us..50us. It's impossible to get a positive pulse width of less than 10uS with NE555. One can replace it with other astable timers ICs, but you need a separate MOSFET driving circuitry. NE555 raising and falling times ~350ns, with a max current of 200mA, which is not enough to quickly switch power MOSFETs ON/OFF. The MOSFET will be in its linear region for some time. Therefore the trigger pulse is set to ~50Hz, letting MOSFET cool down between pulses. Also, notice that the current sense shunt, capacitor bank ESR and traces resistance limits max current to ~56A. You would want to rig some sort of replacable solder-pads on the top of the PCB, so you can finger-press small SMD inductors to it and solder large ones to take measurements. There are header holes for this.

  • Unplug the power
  • Turn the potentiometer all the way counterclockwise. Set the duration selector jumper to the shortest range.
  • Connect oscilloscope probes
  • Plug the power
  • Look at the oscilloscope
  • Turn the potentiometer clockwise (increasing the pulse width) until you see the saturation knee
  • If you still see a linear ramp, unplug, change the duration selector jumper to the next position, turn the potentiometer all the way counterclockwise and repeat
  • Take measurements

Knee

Schematic

Manufacturing

PCB Top view PCB STEP model

Parts

26
QtyValueFootprintReferences
3100nFCapacitor_SMD:C_1206_3216MetricC1, C2, C3
3MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2, H3
2LOAD+Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.3mmJ1, J2
1100kResistor_SMD:R_0805_2012MetricR1
1100mResistor_SMD:R_2512_6332MetricR4
1100nCapacitor_SMD:C_1206_3216MetricC7
1100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC5
1100uFCapacitor_THT:CP_Radial_D5.0mm_P2.00mmC4
1100uHInductor_SMD:L_Taiyo-Yuden_NR-60xx_HandSolderingL1
115kResistor_SMD:R_0805_2012MetricR6
11N4148!my-kicad-library:D_4148_SMDD2
130kResistor_SMD:R_0805_2012MetricR3
1820Resistor_SMD:R_0805_2012MetricR2
191kResistor_SMD:R_0805_2012MetricR5
1FR9888SPGTRPackage_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.514x3.2mmIC1
1LM358Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU1
1LOAD+!my-kicad-library:SolderWire-slotJ3
1LOAD-!my-kicad-library:SolderWire-slotJ4
1MBRA340T3GDiode_SMD:D_SMAD1
1support!my-kicad-library:SolderWire-slotJ5

The 25 most common of 26 parts.

Similar boards

  • 4 layers101 × 175 mmPower PCB, the printed circuit board in 3D

    Power PCB

    ICRS/IPRL-Electronics-Hardware

    96 parts1
  • 4 layers66 × 100 mmPixy M2, the printed circuit board in 3D

    Pixy M2

    Galm007/KiCad-Pixy-M2

    Schematic For Our Micromouse Robot "Pixy M2"

    79 partsMIT
  • 4 layers89 × 72.2 mmOcean harness, the printed circuit board in 3D

    Ocean harness

    jericho-adler/ocean-harness

    An ADAS CAN interposer for the Fisker Ocean, designed in KiCad. It plugs in between the car's harness and the ADAS ECU's main connector (CON1), so a comma device can sit between the car and the ECU.

    33 partsCERN-OHL-S-2.0
  • 4 layers112.5 × 120 mmGateDriver, the printed circuit board in 3D

    GateDriver

    datacrystals/TractionInverterV3

    109 parts1
  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342

Questions

How big is the Flame lamp led driver PCB?

It measures 40 × 35.2 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Flame lamp led driver use?

26 parts, built around the FR9888SPGTR, LM358 and MBRA340T3G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Flame lamp led driver KiCad files?

From the ikatkov/flame-lamp-led-driver repository on GitHub, at the commit this page was made from: the board is main.kicad_pcb and its schematic main.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Flame lamp led driver design in my own project?

Its repository states no licence, so its author keeps all rights: ask ikatkov before reusing the design.