
Esp32Drone
HexaBitsEdu/ESP32-MiniDrone
this project is a drone based on esp32 microcontroller and coreless DC motor

A custom breakout surface board called: IKSTM32BSB. This BSB connects an USB-C power receptacle and a MPU 6050 to a STM32G431KBT microcontroller.
IKSTM32BSB is an open-source printed circuit board by IanKingKung, from the IanKingKung/Custom-BSB repository on GitHub. It is a 2-layer board of 49 × 54.8 mm with 28 parts on 51 nets, routed with 218 tracks and 29 vias.
It is built around the AP2112K-3.3 and MPU-6050. Its parts include 10 capacitors, 7 resistors, 3 ICs, 2 diodes and 2 connectors. It belongs with the STM32 boards of this library.
A custom breakout surface board called: IKSTM32BSB. This BSB connects an USB-C power receptacle and a MPU 6050 to a STM32G431KBT microcontroller. The Vbus of the USB-C power receptacle is filtered through an LDO Regulator to 3.3V which is then fed into both the MPU 6050 and STM32 microcontroller. The user of the BSB board can manually input SDA, SCL, SWCLK, SWDIO, GND, NRST, and INT pins.
The applications for this BSB are wide, allowing for the configuration of multiple sensors through the SDA and SCL pins and actual logic with the STM32 microcontroller.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100nF | Capacitor_SMD:C_1808_4520Metric_Pad1.72x2.30mm_HandSolder | C3, C4, C5, C6, C7, C10 |
| 2 | 1kOhm | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R6, R7 |
| 2 | 2.2uF | Capacitor_SMD:C_0504_1310Metric_Pad0.83x1.28mm_HandSolder | C1, C2 |
| 2 | 4.7kOhm | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1, R2 |
| 2 | 5.1kOhm | Resistor_SMD:R_1210_3225Metric_Pad1.30x2.65mm_HandSolder | R3, R4 |
| 1 | 10nF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C9 |
| 1 | 1M_Ohm | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R5 |
| 1 | 2.2nF | Capacitor_SMD:C_0504_1310Metric_Pad0.83x1.28mm_HandSolder | C8 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U1 |
| 1 | STATUS_LED1 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | STATUS_LED2 | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D2 |
| 1 | STM32G431KBTx | Package_QFP:LQFP-32_7x7mm_P0.8mm | U2 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x_6P_TopMnt_Horizontal | J1 |
The 24 most common of 28 parts.

HexaBitsEdu/ESP32-MiniDrone
this project is a drone based on esp32 microcontroller and coreless DC motor


adityarawat1223/Vibration-Detector
Vibration diagnostic tool using STM32 bare-metal C, on-chip FFT, and custom PCB hardware for bearing fault detection.


angelowickramasinghe/Project-Drone
AeroFC-1S 1S brushed micro-quad flight controller (KiCad) — schematic, PCB, Gerbers, LCSC BOM

atireksd11/Astra-Companion
This repo holds the carrier PCB, the voice stack on the laptop, and notes for building Astra. Week 1 was the KiCad board.

BearsBearsBearsT-T/ESP32-Rocket-Sim-PCB
An MPU and ESP32 powered PCB that tracks motion in real time.

Calinoux7/MoveIt_PCB
Motion Game Controller PCB designed with KiCad 10 – ESP32-S3, MPU-6050, OLED display and I2S audio.
It measures 49 × 54.8 mm and has 2 copper layers, 1.6 mm thick.
28 parts, built around the AP2112K-3.3 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the IanKingKung/Custom-BSB repository on GitHub, at the commit this page was made from: the board is IKSTM32BSB.kicad_pcb and its schematic IKSTM32BSB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask IanKingKung before reusing the design.