Skip to the content
4 layers104 × 103 mmPanel, the printed circuit board in 3D

PoC hardware design of ESP32-S3 + 16MB (APS12808L-3OBM-BA?) PSRAM

Size
104 × 103 mm
Copper layers
4
Thickness
1.69 mm
Parts
162
Nets
372
Pads
1,134
Tracks, vias
4,446, 1,212
Pours
24
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
31 Aug 2022
Updated
22 Sep 2022

Overview

Panel is an open-source printed circuit board by huming2207, from the huming2207/jumbo-s3 repository on GitHub. It is a 4-layer board of 104 × 103 mm with 162 parts on 372 nets, routed with 4,446 tracks and 1,212 vias.

It is built around the ESP32-S3 and APS12808L-3OBM-BA. Its parts include 90 capacitors, 18 resistors, 12 ICs, 12 inductors and 6 connectors. It belongs with the ESP32 boards of this library.

Main components

2

README

README.md

jumbo-s3

PoC hardware design of ESP32-S3FN8 + 16MB (APS12808L-3OBM-BA) PSRAM

Intro

As of September 2022, Espressif doesn't provide an official solution for ESP32-S3 that comes with more than 8MB PSRAM. However someone mentioned that the APS12808L works with ESP32-S3 but no open source design.

Therefore here comes my solution. It has been proven working fine. No modification needed for ESP-IDF. As long as the PSRAM support is enabled and set to octal mode, 80MHz, it should just works.

Log

Here's a simple boot log that runs the APS12808L in octal SPI mode at 80MHz, and logs the free heap size.

text
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x8 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3810,len:0x1808
load:0x403c9700,len:0xd6c
load:0x403cc700,len:0x2ed4
entry 0x403c992c
I (24) boot: ESP-IDF v5.1-dev-862-g09f7589ef2 2nd stage bootloader
I (25) boot: compile time Sep 20 2022 23:02:14
I (25) boot: chip revision: V001
I (29) boot_comm: chip revision: 1, min. bootloader chip revision: 0
I (36) qio_mode: Enabling default flash chip QIO
I (42) boot.esp32s3: Boot SPI Speed : 80MHz
I (46) boot.esp32s3: SPI Mode       : QIO
I (51) boot.esp32s3: SPI Flash Size : 4MB
I (56) boot: Enabling RNG early entropy source...
I (61) boot: Partition Table:
I (65) boot: ## Label            Usage          Type ST Offset   Length
I (72) boot:  0 nvs              WiFi data        01 02 00009000 00006000
I (79) boot:  1 phy_init         RF data          01 01 0000f000 00001000
I (87) boot:  2 factory          factory app      00 00 00010000 00100000
I (94) boot: End of partition table

Parts

162
QtyValueFootprintReferences
300.1uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C1, C1, C1, C1, C1, C2, C2, C2, C2, C2, C2, C3, C3, C3, C3 +14
241uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC6, C6, C6, C6, C6, C6, C7, C7, C7, C7, C7, C7, C8, C8, C8, C8 +8
1210kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R1, R1, R1, R1, R1, R2, R2, R2, R2, R2, R2
12NCCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC13, C13, C13, C13, C13, C13, C14, C14, C14, C14, C14, C14
12TBDCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC12, C12, C12, C12, C12, C12, C15, C15, C15, C15, C15, C15
610nFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC10, C10, C10, C10, C10, C10
610uFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC11, C11, C11, C11, C11, C11
62.0nHInductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolderL1, L1, L1, L1, L1, L1
640MHz 10ppmCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mm_HandSolderingY1, Y1, Y1, Y1, Y1, Y1
6499RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR3, R3, R3, R3, R3, R3
6ANTRF_Antenna:Texas_SWRA117D_2.4GHz_LeftAE1, AE1, AE1, AE1, AE1, AE1
6APS12808L-3OBM-BAJackco:MINIBGA-24LU2, U2, U2, U2, U2, U2
6ESP32-S3Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP5.6x5.6mmU1, U1, U1, U1, U1, U1
6GPIOConnector_PinHeader_1.27mm:PinHeader_2x22_P1.27mm_Vertical_SMDJ1, J1, J1, J1, J1, J1
6TBDInductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolderL2, L2, L2, L2, L2, L2

The 150 most common of 162 parts.

More from huming2207/jumbo-s3

1
  • 4 layers38 × 25 mmJumbo s3, the printed circuit board in 3D

    Jumbo s3

    huming2207/jumbo-s3

    PoC hardware design of ESP32-S3 + 16MB (APS12808L-3OBM-BA?) PSRAM

    25 parts9

Similar boards

  • 2 layers83.2 × 40 mmSmartdisplay, the printed circuit board in 3D

    Smartdisplay

    BearLaboratory/smartdisplay-hardware

    2.9寸墨水屏个人显示终端硬件显示

    46 parts175GPL-3.0
  • 2 layers168.9 × 123.3 mmOEM ECU, the printed circuit board in 3D

    OEM ECU

    aeonSolutions/AeonLabs-AI-Volvo-MKII-Open-Hardware

    Volvo MKII Open Hardware

    296 parts161CC0-1.0
  • 2 layers35.4 × 27 mmWifiaudio, the printed circuit board in 3D

    Wifiaudio

    BearLaboratory/wifiaudio-tx-hardware

    WiFi无线麦克风硬件pcb设计

    29 parts110GPL-3.0
  • 4 layers100 × 100 mmPCBA OCTV, the printed circuit board in 3D

    PCBA OCTV

    intechstudio/grid-hardware

    403 parts59GPL-3.0
  • 4 layers88 × 30 mmOled nametag, the printed circuit board in 3D

    Oled nametag

    TobleMiner/oled-nametag

    A ESP32-based OLED nametag

    123 parts54CERN-OHL-P-2.0
  • 4 layers93.5 × 118.6 mmRD56, the printed circuit board in 3D

    RD56

    lhm0/rotating_display_color

    56 LED rotating color display with RP2040 and ESP32 microcontrollers

    266 parts25

Questions

How big is the Panel PCB?

It measures 104 × 103 mm and has 4 copper layers, 1.69 mm thick.

What parts does the Panel use?

162 parts, built around the ESP32-S3 and APS12808L-3OBM-BA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Panel KiCad files?

From the huming2207/jumbo-s3 repository on GitHub, at the commit this page was made from: the board is panel/panel.kicad_pcb and its schematic jumbo-s3/jumbo-s3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Panel design in my own project?

Its repository states no licence, so its author keeps all rights: ask huming2207 before reusing the design.