Skip to the content
2 layers46 × 73.7 mmRolling resistance, the printed circuit board in 3D

The system used to collect and process data from our rolling resistance tester.

Size
46 × 73.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
34
Pads
60
Tracks, vias
29, 0
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
6 Jun 2021
Updated
3 Feb 2024

Overview

Rolling resistance is an open-source printed circuit board by hpvdt, from the hpvdt/rolling_resistance_rig repository on GitHub. It is a 2-layer board of 46 × 73.7 mm with 14 parts on 34 nets, routed with 29 tracks and 0 vias.

It is built around the LM358. Its parts include 4 resistors, 2 diodes, 2 connectors and 1 IC. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

1

README

README.md

Rolling Resistance Rig (RRR)

One of the most crucial aspects of our land vehicles is the study of rolling resistance and our pursuit of reducing it. To this end the team has constucted a rolling resistance rig (RRR) to characterize different wheels. This repository serves as the definitive collection of information related to the RRR and its tests: especially the sensor system design and data processing.

The general principle of the RRR is that there is a large drum which acts as the riding surface for the wheel and is spun up to speed by an electric motor to simulate speeds of over 80 km/h. The wheel under test is installed above the wheel and is loaded to a similar level to the expected vehicle load prior to the drum getting spun up. Once the desired speed is achieved by the system, the power to the drum is cut and the drum/wheel combo is left to slow down by dissipating power primarily through their own rolling resistances.

During this slowdown the rotational period of each part is monitored and recorded over serial to then be analyzed and derive a rolling resistance for the wheel being tested. This processing is performed after the experiment is concluded in MATLAB.

The exact procedure for this process is outlined in a separate markdown file, test_procedure.md.

Repository Organization

There are a few folders used to sort the different components of the system.

FolderPurpose
analysisPrimarily the MATLAB files used to process the data collected
analysis/dataPreviously collected experiment data
arduinoMicrocontroller code used to collect data. USE THE rolling_resistance SKETCH!
docAssorted documentation about the system design
hardwareHardware files for custom circuit boards designed for this system

Software Used

A few programs are needed to fully operate the system. No additional configuration is needed to any of the software to run the system (e.g. installing custom libraries).

  • Arduino IDE (V 2.1.0 as of writting) for programming the microntrollers used (Arduino Nanos/Unos).
  • KiCad 7 for the most recent board's hardware files. The previous version was prepared in EAGLE.
  • MATLAB for post-processing of the data collected.
  • Excel/LibreOffice Calc to store some results.

Future Improvements

  • Record procedure to determine inertia characteristics of a wheel as part of this repository
  • Improve the data processing scripts. More information in its readme.

Parts

14
QtyValueFootprintReferences
210KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2
2330Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R4
2Conn_01x03Connector_JST:JST_EH_B3B-EH-A_1x03_P2.50mm_VerticalJ1, J2
2LEDLED_THT:LED_D4.0mmD1, D2
1Arduino_Nano_v3.xModule:Arduino_NanoA1
1LM358Package_DIP:DIP-8_W7.62mmU1

The 10 most common of 14 parts.

Similar boards

  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342
  • 2 layers68.8 × 53.6 mmZArduino, the printed circuit board in 3D

    ZArduino

    zmaker/arduino_cookbook

    gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

    46 parts269
  • 2 layers152 × 88 mmRFBitBangSMT, the printed circuit board in 3D

    RFBitBangSMT

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    271 parts222
  • 2 layers118 × 103.5 mmEV Charger2, the printed circuit board in 3D

    EV Charger2

    fotherja/EV_Charger

    Arduino Uno Code for EV Charger

    62 parts167MIT
  • 2 layers113 × 62.2 mmFullScope, the printed circuit board in 3D

    FullScope

    tvlad1234/pillScopePlus

    Oscilloscope based around the STM32F401 Black Pill and a color LCD screen

    15 parts165Apache-2.0
  • 2 layers75.2 × 61.1 mmHelios, the printed circuit board in 3D

    Helios

    Grix/helios_dac

    Helios Laser DAC

    102 parts132
  • 2 layers144.1 × 182.2 mmSHVC CPU-01, the printed circuit board in 3D

    SHVC CPU-01

    starlightk7/OpenSFC

    OSHW Reproduction Parts related to the Super Famicom / Super Nintendo game console

    498 parts114CERN-OHL-S-2.0
  • 2 layers100 × 85 mmVNA, the printed circuit board in 3D

    VNA

    profdc9/VNA

    Vector Network Analyzer based on the STM32F103C8T6 bluepill

    178 parts93

Questions

How big is the Rolling resistance PCB?

It measures 46 × 73.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rolling resistance use?

14 parts, built around the LM358. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rolling resistance KiCad files?

From the hpvdt/rolling_resistance_rig repository on GitHub, at the commit this page was made from: the board is hardware/rolling_resistance/rolling_resistance.kicad_pcb and its schematic hardware/rolling_resistance/rolling_resistance.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rolling resistance design in my own project?

Its repository states no licence, so its author keeps all rights: ask hpvdt before reusing the design.