

RpiReceiverV7 1
Service List: | MHz | Service ID | SubChId | FIC | Strength | Country | Version | started | Label | | --- | --- | --- | --- | --- | --- | --- | --- | --- | | 187.072 | 3153 | 2 | 100 | 43 | 10 | 46 | - | ENERGY | |…
- Size
- 65 × 56.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 80
- Nets
- 52
- Pads
- 352
- Tracks, vias
- 666, 69
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 22 Mar 2021
- Updated
- 21 Feb 2021
Overview
RpiReceiverV7 1 is an open-source printed circuit board by hitech95, from the hitech95/si468x_dab_receiver repository on GitHub. It is a 2-layer board of 65 × 56.5 mm with 80 parts on 52 nets, routed with 666 tracks and 69 vias.
It is built around the SI4688-A10-GM, SSM2518CPZ and 74AHC1G66GV, with the CAT24C512WI-, DS3231MZ/V+ and OPT3001 among its other parts. Its parts include 28 capacitors, 12 resistors, 11 ICs, 3 connectors and 2 inductors.
Main components
7SI4688-A10-GM
QFN-48(7x7)-40℃~+85℃ 76MHz~108MHz、168MHz~240MHz Receivers SPI、I2C VHF、FM QFN-48(7x7) RF Transceiver ICs ROHSSilicon LabsRF Transceiver ICsSSM2518CPZ
LFCSP-20(4x4)-40℃~+85℃ 0.04% 2-Channel 2.5V~5.5V 2.5Wx2@4Ω 4.7mA 80dB 91% 97dB Automatic mute/no-noise switch、Enable/shutdown function、Filterless architecture、Digitally programmable gain、Built-in audio processing、Automatic power-saving mode Class D LFCSP-20(4x4) Audio Amplifiers ROHSAnalog DevicesAudio Amplifiers74AHC1G66GV
SOT-753-40℃~+125℃ 1 11ns 16Ω 17ns 1:1 280MHz 2V~5.5V 3ns 4pF SOT-753 Analog Switches, Multiplexers ROHSNexperiaAnalog Switches, MultiplexersCAT24C512WI-
SOP-8-40℃~+85℃ 1,000,000 cycles 1.8V~5.5V 100 Years 1MHz 512Kbit 5ms Hardware write protection function、Noise suppression function、Built-in power-on reset (POR)、Built-in error correction code (ECC) function I2C SOP-8 EEPROM ROHSonsemiEEPROMDS3231MZ/V+
SOIC-8-40℃~+85℃ 2.3V~5.5V Built-in I2C Temperature compensation、Backup power management and battery charging、Alarm function、Locking and tamper-proof、Periodic interrupt output SOIC-8 Real Time Clocks ROHSMaxim Integrated (Analog Devices)Real Time ClocksOPT3001
DFN-6(2x2)DFN-6(2x2) New Arrivals ROHSEverlight ElectronicsUncategorisedCM1213A-01SO
SOT-23-40℃~+85℃ 0.85pF 10V 1A 1uA 3.3V 9V ESD IEC 61000-4-2 Single-channel SOT-23 ESD and Surge Protection (TVS/ESD) ROHSonsemiESD And Surge Protection (TVS/ESD)
README
README.mdSI468x DAB Receiver modules and design files
To compile modules install kernel headers
sudo apt-get install -y raspberrypi-kernel-headersthen run
sudo install.shand reboot, that's it. Take care of the Device-Tree
Without a PLL not all MCLK and BCLK combinations are supported
add the alsa configuration
sudo cp /home/pi/rpi-receiver-linux-rpi-*/asound.conf /etc/SI468x Firmware
unfortunately the firmware is closed source. You can buy an EVAL Board to get old ones (that is what I did). Copy files:
sudo cp -r /home/pi/rpi-receiver-linux-rpi-*/si468x /lib/firmwareYou can copy the files to the connected EEPROM:
echo fm | sudo tee /sys/devices/platform/soc/*.i2c/i2c-1/1-0064/si468x_nvramcopies the fm firmware referenced from the devicetree to the nvram
Tuning
You can use the v4l2 tools
v4l2-ctl -d /dev/radio0 --set-freq=88.80tunes to FM 88.8MHz.
Search next station
v4l2-ctl -d /dev/radio0 --freq-seek=dir=1,wrap=1 && v4l2-ctl -d /dev/radio0 --get-freqAdjusting volume
v4l2-ctl -d /dev/radio0 --set-ctrl volume=63sets the volume and activates the analog output of the SI468x
Tuning to DAB
simply use a frequency in the DAB Band
v4l2-ctl -d /dev/radio0 --freq-seek=low=187.072,high=3412,spacing=0 && cat /sys/devices/platform/soc/*.i2c/i2c-1/1-0064/si468x_service_listwill also print a service list
Service List:
| MHz | Service ID | SubChId | FIC | Strength | Country | Version | started | Label |
|---|---|---|---|---|---|---|---|---|
| 187.072 | 3153 | 2 | 100 | 43 | 10 | 46 | - | ENERGY |
| 187.072 | 989 | 1 | 100 | 43 | 10 | 46 | - | R.Maria |
| 187.072 | 3416 | 10 | 100 | 43 | 10 | 46 | - | WELLE 1 |
| 187.072 | 3154 | 9 | 100 | 43 | 10 | 46 | - | Stephans Klassik |
| 187.072 | 3413 | 12 | 100 | 43 | 10 | 46 | - | Mein Kinderradio |
| 187.072 | 3364 | 8 | 100 | 43 | 10 | 46 | - | ERF Plus |
| 187.072 | 3370 | 7 | 100 | 43 | 10 | 46 | - | Technikum ONE |
| 187.072 | 3367 | 6 | 100 | 43 | 10 | 46 | - | Rock Antenne |
| 187.072 | 3414 | 3 | 100 | 43 | 10 | 46 | - | j▒.live |
| 187.072 | 3143 | 5 | 100 | 43 | 10 | 46 | - | * 88.6 * |
| 187.072 | 3412 | 0 | 100 | 43 | 10 | 46 | * | ARABELLA RELAX |
| 187.072 | 3411 | 11 | 100 | 43 | 10 | 46 | - | KLASSIK RADIO |
use MHz for the low and Service ID for the high argument to tune with v4l2-ctl
Get the dynamic label
cat /sys/devices/platform/soc/*.i2c/i2c-1/1-0064/si468x_dynamic_labelToDo
- in Austria DAB is broadcasted on a single band - never tried two bands....
- HF receiver circuit needs to be tuned - needs time and equipment!
- Charset is not converted (j▒.live should be jö.live), but I do not know if this makes sense in the module
Parts
80| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1, C2, C3, C4, C5, C6, C12, C13, C20, C21 |
| 10 | 3k9 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R9, R10, R11 |
| 5 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C15, C18, C19, C22, C27 |
| 4 | 2n2 | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C14, C16, C17, C23 |
| 4 | 470p | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C8, C9, C10, C11 |
| 4 | Ferrite_Bead_Small | Inductor_SMD:L_0603_1608Metric | FB1, FB2, FB3, FB4 |
| 3 | 8p2 | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C24, C25, C26 |
| 3 | AP2127N-1.8 | Package_TO_SOT_SMD:SOT-23 | U9, U10, U11 |
| 3 | MountingHole | MountingHole_:MountingHole_2.7mm_M2.5 | H1, H2, H3 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3 |
| 2 | Symbol_:HTL-Steyr-Logo_4x4mm_Copper | Logo2, Logo3 | |
| 2 | 100 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R8, R12 |
| 2 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | DNP_J3, DNP_J6 |
| 2 | Conn_01x02 | Connector_TE-Connectivity_:TE_2834085-1_1x02_P2.54mm_45deg | J4, J5 |
| 2 | TestPoint_Flag | TestPoint:TestPoint_Pad_D1.0mm | TP4, TP5 |
| 1 | Symbol:OSHW-Logo2_7.3x6mm_Copper | Logo1 | |
| 1 | Symbol_:HTL-Steyr-Logo_4x4mm_SilkScreen | Logo4 | |
| 1 | 10pF | Capacitor_SMD:C_0603_1608Metric | C28 |
| 1 | 120nH | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 4u7/25V | Capacitor_SMD:CP_Elec_4x5.4 | C7 |
| 1 | 62nH | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 74AHC1G66 | Package_TO_SOT_SMD:SOT-353_SC-70-5 | U3 |
| 1 | Antenna | Connector_Pin:Pin_D1.0mm_L10.0mm | AE1 |
| 1 | Battery_Cell | Battery:BatteryHolder_Keystone_3002_1x2032 | BT1 |
| 1 | CAT24C512 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | CM1213A-01SO | Package_TO_SOT_SMD:SOT-23 | D1 |
| 1 | Conn_Coaxial | Connector_Coaxial:SMA_Molex_73251-1153_EdgeMount_Horizontal | DNP_J2 |
| 1 | Crystal_GND24_Small | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1 |
| 1 | DS3231MZ | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | OPT3001 | Package_DFN_QFN_:DNP-6-1EP_2.1x2.1mm_P0.65mm_EP0.65x1.35mm | U5 |
| 1 | PI40HAT | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J2 |
| 1 | PI4HAT | Connector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_Vertical | DNP_J1 |
| 1 | SSM2518 | Package_CSP_:LFCSP-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U6 |
| 1 | SST25VF016B-50-4x-S2Ax | Package_SO:SOIC-8_5.275x5.275mm_P1.27mm | U8 |
| 1 | Si4688-A10-GM | Package_DFN_QFN_:QFN-48-1EP_7x7mm_P0.5mm_EP5.3x5.3mm_ThermalVias | U7 |
| 1 | TSOP43xx | OptoDevice:Vishay_MOLD-3Pin | U4 |
Similar boards
- 2 layers64.5 × 41.9 mm

- 4 layers36 × 40 mm

- 2 layers165.8 × 130.8 mm

YAEMK
KarlK90/yaemk-split-kb
5x8 Split keyboard with thumb-clusters, rotary encoders and oleds.
218 parts128GPL-3.0 - 13 layers38.5 × 38.5 mm

Xbox Charge
Redherring32/100W-Charging-PCB
100W USB C PD Lithium Ion charging PCB based on the TPS25750D and BQ25713
90 parts43 - 2 layers100 × 100 mm

JukeBox
FriendTeamInc/JukeBox
An affordable, adorable, powerful hotkey device to run macros, play funny sounds, managing your audio settings, change paint brush settings, configuring items in OBS, and so much more!
102 parts1 - 4 layers150.6 × 89.9 mm

AdvDash 5 inch
ADVecu/ADV.dash
ADV.dash is a dashboard project built with LVGL and ESP32-S3. It is prepared to receive CAN bus data from rusEFI and, in the future, other programmable ECUs.
190 parts - 4 layers85.4 × 47.2 mm

- 2 layers57.4 × 12 mm

Questions
How big is the RpiReceiverV7 1 PCB?
It measures 65 × 56.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the RpiReceiverV7 1 use?
80 parts, built around the SI4688-A10-GM, SSM2518CPZ, 74AHC1G66GV and CAT24C512WI-. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the RpiReceiverV7 1 KiCad files?
From the hitech95/si468x_dab_receiver repository on GitHub, at the commit this page was made from: the board is KiCad/rpiReceiverV7_1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the RpiReceiverV7 1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask hitech95 before reusing the design.