

Kizami
FPGA side of Kizami — cycle-exact timecode + audio witness on iCE40
- Size
- 80 × 45 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 23
- Pads
- 170
- Tracks, vias
- 1,156, 83
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 6 Sep 2026
- Updated
- 21 Sep 2026
Overview
Kizami is an open-source printed circuit board by hasky00, from the hasky00/kizami-core repository on GitHub, published under the MIT licence. It is a 2-layer board of 80 × 45 mm with 36 parts on 23 nets, routed with 1,156 tracks and 83 vias.
It is built around the CH340C, ESP32-WROOM-32 and AMS1117-3.3, with the DS3231SN#T&R, S8050 and CR2032 among its other parts. Its parts include 11 resistors, 9 capacitors, 5 connectors, 4 ICs and 2 transistors. It belongs with the fPGA and programmable logic and audio and music boards and the ESP32 boards of this library.
Main components
6CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersESP32-WROOM-32
SMD,18x25.5mm-40℃~+85℃ -98dBm 2.4GHz 2.7V~3.6V 20dBm Bluetooth4.2 ESP32-DOWDQ6 UART、SDIO、SPI、I2C、GPIO、PWM、ADC、DAC SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsDS3231SN#T&R
SOIC-16-300mil-40℃~+85℃ 0.84uA 2.3V~5.5V 200uA Built-in I2C Temperature compensation、Programmable clock output、Alarm function Yes SOIC-16-300mil Real Time Clocks ROHSMaxim Integrated (Analog Devices)Real Time ClocksS8050
SOT-23-55℃~+150℃ 1 NPN 100MHz 100nA 120 25V 300mW 500mA 5V 600mV NPN SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)CR2032
-- Unclassified goods ROHSMaxellUncategorised
README
README.md
kizami-core
The FPGA side of Kizami — a Nostr-timestamped audio witness. Runs on the open-hardware Alhambra II (iCE40HX4K).
rtl/— Verilog.timecode.vis the HH:MM:SS:FF counter,top.vmaps it to LEDs.icestudio/—.icedesigns for Icestudio / FPGALab.labs/— FPGALab workbench configs.docs/— LTC frame layout and the roadmap.
Simulate (no hardware)
- Open
icestudio/design in Icestudio, build once soice-build/exists. fpga-lab --ice icestudio/<design>.ice --clock-hz 1200000(slow mode, readable LEDs).
Build & flash (Alhambra II)
pip install apio && apio install --all
apio build && apio uploadLED0–4 = frame count in binary, LED7 = blinks once per second.
License: MIT
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R4, R7, R8, R9, R11 |
| 4 | 10uF | Capacitor_SMD:C_0603_1608Metric | C2, C4, C5, C8 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C6, C9 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | S8050 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | BTN1 REC | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | BTN2 MENU | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U3 |
| 1 | CR2032 | Battery:BatteryHolder_Keystone_3034_1x20mm | BT1 |
| 1 | DS3231SN | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U2 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U1 |
| 1 | JACK TIP RING SLEEVE | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | OLED GND VCC SCL SDA | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | USB-C | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J6 |
Similar boards
- 2 layers85 × 56 mm

- 2 layers35 × 45 mm

LVGLDevKit
jppang/ESP32_MicroPython_LVGL_ST7789
Try to build an ESP32 firmware with LVGL and ST7789 drivers inside.
40 parts2 - 4 layers100 × 80 mm

Hackathon board v2
Brian-Nziza/ESP32-Hackathon-Board
KiCad 10 project. Board is 100 × 80 mm, four layers, fabricated by JLCPCB.
75 parts - 2 layers162.8 × 99.9 mm

PSU
Sakib-Ansari/Linear_Programmable_Power_Supply
This repository contains the complete KiCad project for a multi-board linear programmable bench power supply. The design is organized into separate PCBs, including the Power Board, Control Board, Front Panel, Output…
133 partsMIT - 4 layers72 × 53 mm

Unijoysticle2 xl800
ricardoquesada/unijoysticle2
Bluetooth gamepad support for the Commodore 64 / Atari / Amiga, etc.
58 parts62 - 2 layers63 × 60.8 mm

Esp32node wip
MadsRudolph/personal-projects
One passive crossover board per speaker, so build two. Single-sided, through-hole only, CNC isolation-milled with an 0.8 mm end mill (the DTU 62768 process).
32 parts - 4 layers100 × 100 mm

PCB Design
ConquerToFreedom/SwasthEdge
Low-cost self-diagnosing edge controller for industrial sensor reliability
89 parts2 - 2 layers49.4 × 95.7 mm

Questions
How big is the Kizami PCB?
It measures 80 × 45 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Kizami use?
36 parts, built around the CH340C, ESP32-WROOM-32, AMS1117-3.3 and DS3231SN#T&R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Kizami KiCad files?
From the hasky00/kizami-core repository on GitHub, at the commit this page was made from: the board is kizami/kizami.kicad_pcb and its schematic kizami/kizami.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Kizami design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).