

Nrfmicro
The best keyboard!
- Size
- 305.8 × 120.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 279
- Nets
- 221
- Pads
- 1,228
- Tracks, vias
- 2,256, 273
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 20 Jul 2026
- Updated
- 26 Sep 2026
Overview
Nrfmicro is an open-source printed circuit board by hashim-cpro, from the hashim-cpro/ultimate-keyboard repository on GitHub. It is a 2-layer board of 305.8 × 120.2 mm with 279 parts on 221 nets, routed with 2,256 tracks and 273 vias.
It is built around the 74AHCT125D, E73-2G4M08S1C and AP2112K-3.3, with the TP4054, 1N4148WT and SK6812MINI-E among its other parts. Its parts include 170 diodes, 85 switches, 8 resistors, 4 ICs and 3 connectors. It belongs with the keyboards and input boards and the nRF52 and nRF5x boards of this library.
Main components
774AHCT125D
SOP-14-40℃~+125℃ 1 4 4.3ns@5V,50pF 4.5V~5.5V 40uA 74AHCT 8mA 8mA Schmitt trigger Tri-State Unidirectional SOP-14 Buffers, Drivers, Receivers, Transceivers ROHSNexperiaBuffer/Driver/TransceiverE73-2G4M08S1C
SMD,18x13mm-103dBm、-95dBm -40℃~+85℃ 120m 17.05mA 3.3V 8.27mA 8dBm Bluetooth 5.0、Bluetooth 4.2 PWM、SPI、ADC、USB、I2C、ISP、JTAG、DMA nRF52840 Chip SMD,18x13mm Bluetooth Modules ROHSChengdu Ebyte Elec TechBluetooth ModulesAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorisedTP4054
SOT-23-5L-40℃~+85℃ 1 25uA 4.2V 4.2V~6.5V 500mA Charging IC Lithium Battery Not supported 恒流充电、恒压充电、涓流充电、自动再充电、充电终止、可编程充电电流、软启动、欠压锁定 SOT-23-5L Battery Management ROHSUMWBattery Management1N4148WT
SOD-523-55℃~+150℃ 1.25V@150mA 100V 150mA 150mW 1uA@75V 2A 4ns Independent SOD-523 Switching Diodes ROHShongjiachengSwitching DiodesSK6812MINI-E
SMD-40℃~+85℃ 0.6mA 1.78mm 120mcd~240mcd 120° 160mcd~320mcd 1kHz 2.8mm 2000V 3.2mm 3.7V~5.5V 460nm~470nm 515nm~525nm 620nm~625nm 800Kbit/s 815mcd~1275mcd Semi-transparent lens SMD RGB LEDs(Built-in IC) ROHSOPSCO OptoelectronicsRGB LEDs(Built-In IC)AO3407
SOT-23-55℃~+150℃ 1 P-Channel 1.4W 1V 260pF 30V 37pF 4.1A 75mΩ@4.5V P-Channel ±20V SOT-23 MOSFETs ROHSBORNMOSFETs
README
README.mdUltimate-keyboard
A custom 75% (84-key) mechanical keyboard built from the ground up with Bluetooth 5.0 wireless & wired USB-C connectivity, individually addressable per-key RGB backlighting, Kailh MX hot-swap sockets, and integrated LiPo battery charging.
It uses the nrfmicro microcontroller architecture as inspiration. Basically, instead of soldering a separate development board onto the keyboard, I copied the microcontroller schematics, put the Nordic nRF52840 SoC (via Ebyte E73 module) directly onto the keyboard's PCB, added battery charging and power management circuitry, and routed the entire PCB myself! At the end of the day, the IC lives right on the keyboard PCB with ample room to route everything cleanly.
3D Renders & Showcase
| Top View | Isometric Side View | Bottom View |
|---|---|---|
![]() | ![]() | ![]() |
| PCB Top Layer | PCB Bottom Layer |
|---|---|
![]() | ![]() |
Project Directory Map
ultimate-keyboard/
├── .github/
│ └── workflows/
│ └── build.yml # Automated ZMK CI build workflow
├── boards/hashim/ultimate_keyboard/ # Zephyr HWMv2 board definition
│ ├── board.yml # Board metadata (SoC: nrf52840, variant: zmk)
│ ├── Kconfig.ultimate_keyboard # Board selection & ZMK_BOARD_COMPAT
│ ├── Kconfig.defconfig # Name & bootloader retention settings
│ ├── ultimate_keyboard.zmk.yml # ZMK hardware metadata catalog
│ ├── ultimate_keyboard_nrf52840_zmk.dts # Devicetree definition (matrix, ADC, SPI RGB)
│ └── ultimate_keyboard_nrf52840_zmk_defconfig # Base Kconfig drivers
├── config/
│ ├── ultimate_keyboard.keymap # 84-key QWERTY + Function layers
│ ├── ultimate_keyboard.conf # Bluetooth TX power, sleep, RGB underglow
│ └── west.yml # Manifest
├── firmware/
│ ├── boards/hashim/ultimate_keyboard/ # Board definition mirror
│ ├── config/ # Keymap and config mirror
│ ├── build.yaml # Firmware build matrix
│ └── ultimate_keyboard.uf2 # Compiled functional flash file (ready to flash)
├── hardware/
│ ├── nrfmicro.kicad_sch
│ ├── nrfmicro.kicad_pcb
│ ├── nrfmicro.kicad_proBill of Materials (BOM)
1. Integrated Circuits & Semiconductors
| Designator | Value / Part | Package / Footprint | Qty | Description |
|---|---|---|---|---|
| U1 | E73-2G4M08S1C | E73-2G4M08S1C-52840 | 1 | Nordic nRF52840 Bluetooth 5.0 & USB 2.0 SoC Module with PCB Antenna |
| U2 | AP2112K-3.3 | SOT-23-5 | 1 | 3.3V 600mA Ultra-Low Dropout (LDO) Linear Voltage Regulator |
| U3 | TP4054 | SOT-23-5 | 1 | Standalone Linear Li-Ion Battery Charger IC |
| U4 | 74AHCT125 | SOIC-14 (3.9x8.7mm, P1.27mm) | 1 | Quad Buffer / 3.3V to 5V Logic Level Shifter for RGB LEDs |
| Q1, Q2 | AO3407 | SOT-23 | 2 | P-Channel 30V MOSFET (Power path switching & battery reverse protection) |
| D100 | 1N5819 | D_SOD-323F | 1 | Schottky Barrier Rectifier Diode (Power OR-ing) |
| D200 | RED LED | LED_0603_1608Metric | 1 | Red 0603 SMD LED (Battery charge indicator) |
2. Key Matrix Diodes & Addressable RGB LEDs
| Designator | Value / Part | Package / Footprint | Qty | Description |
|---|---|---|---|---|
| D1 – D84 | 1N4148WT | D_SOD-123 | 84 | High-Speed Switching Diodes (Anti-Ghosting / NKRO Matrix) |
| LED1 – LED84 | SK6812MINI-E | MX_SK6812MINI-E_REV | 84 | Reverse-Mount Individually Addressable RGB LEDs |
3. Kailh MX Hot-Swap Sockets
| Designator | Key Size | Footprint | Qty | Target Keys |
|---|---|---|---|---|
| SW2, SW29, ... | 1.00u Socket | SW_Hotswap_Kailh_MX_1.00u | 73 | Standard 1u Alpha, Number, Function & Navigation keys |
| SW75, SW76, SW77 | 1.25u Socket | SW_Hotswap_Kailh_MX_1.25u | 3 | Left Ctrl, Left Win, Left Alt |
| SW45, SW32 | 1.50u Socket | SW_Hotswap_Kailh_MX_1.50u | 2 | Tab, Backslash (|) |
| SW47, SW72 | 1.75u Socket | SW_Hotswap_Kailh_MX_1.75u | 2 | Caps Lock, Right Shift |
| SW30 | 2.00u Socket | SW_Hotswap_Kailh_MX_2.00u | 1 | Backspace |
| SW59, SW61 | 2.25u Socket | SW_Hotswap_Kailh_MX_2.25u | 2 | Left Shift, Enter |
| SW78 | 6.25u Socket | SW_Hotswap_Kailh_MX_6.25u | 1 | Spacebar |
| Total Sockets | 84 | Full 75% layout coverage |
4. Connectors, Switches & Crystal
| Designator | Value / Part | Package / Footprint | Qty | Description |
|---|---|---|---|---|
| J1 | USB-C Receptacle 16-pin | USB-C_C168688 | 1 | USB Type-C Receptacle (16-Pin) |
| J2 | Conn_01x04 | connector_swd | 1 | 4-Pin SWD Header (VDD, SWDIO, SWCLK, GND) |
| J3 | Conn_01x02 | PinSocket_1x02_P1.27mm_Vertical | 1 | 2-Pin Battery Header (for LiPo battery) |
| SW85 | Tactile Switch | SW_Push_SPST_NO_Alps_SKRK | 1 | Tactile Push Button (Reset / Bootloader mode) |
| RESET | TestPoint | TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | 1 | Hardware Reset Test Point |
| X1 | 32.768kHz Crystal | CM9V-T1A-2Pin_1.6x1.0mm | 1 | MicroCrystal CM9V-T1A low-frequency crystal for BLE sleep mode |
5. Resistors (SMD 0603)
| Designator | Value | Footprint | Qty | Function / Notes |
|---|---|---|---|---|
| R1 | 100kΩ | R_0603_1608Metric | 1 | Pull-up / Gate bias resistor |
| R2, R3 | 5.1kΩ | R_0603_1608Metric | 2 | USB Type-C CC1 / CC2 pull-down resistors (5V host negotiation) |
| R5 | RPROG | R_0603_1608Metric | 1 | Charge current setting resistor for TP4054 |
| R6 | 820kΩ | R_0603_1608Metric | 1 | Voltage divider bias resistor |
| R7, R9 | 2MΩ | R_0603_1608Metric | 2 | High-impedance battery voltage monitoring divider |
| R8 | 1kΩ | R_0603_1608Metric | 1 | Current limiting resistor for indicator LED |
Wiring Diagram
see in pdf
Schematics

Firmware (ZMK)
The keyboard runs native ZMK Firmware built on the Zephyr RTOS with full support for Bluetooth Low Energy 5.0, USB HID, low-power deep sleep, battery level telemetry, and individually addressable RGB backlighting.
A pre-compiled, tested, ready-to-flash binary is available at: firmware/ultimate_keyboard.uf2
How to Build the Firmware
GitHub Actions (Recommended & Automated)
This repository includes a GitHub Actions workflow in .github/workflows/build.yml configured with ZMK's official build matrix. Every push to main automatically triggers a build in the cloud.
- Edit your keymap in
config/ultimate_keyboard.keymapor settings inconfig/ultimate_keyboard.conf. - Commit and push your changes:
- Once the workflow run completes, click into the run, scroll to Artifacts, and download
ultimate_keyboard.zip. - Extract the
.uf2file and flash it!(enter bootloader mode by holding the dedicated button beneath space bar)
Assembly
After getting the PCB and the components, you can assemble the keyboard by following these steps:
- first of all solder the MCU and the ICs surrounding it on the top side of the PCB with a heat gun.
- then solder the usbc port and the boot button and the battery connections header(you can solder the wires directly to the pads if you want).
- then solder the diodes, rgb leds and switch sockets along with everything remaining on the bottom side of the PCB.
- connect the battery, flash the firmware, put the switches in and then you can test the keyboard and make sure everything is working properly.
AI Usage Declaration
I used AI for research, general queries and for asking question like using it instead of google, and formatting the markdown documentation and BOM tables. and fixing firmware as well.
Parts
279| Qty | Value | Footprint | References |
|---|---|---|---|
| 84 | 1N4148WT | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +68 |
| 84 | SK6812MINI-E | keyboard-parts:MX_SK6812MINI-E_REV | LED1, LED2, LED10, LED11, LED12, LED13, LED14, LED15, LED16, LED17, LED18, LED19, LED20, LED21, LED22, LED23 +68 |
| 73 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_1.00u | SW1, SW2, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW20, SW21, SW22, SW23 +57 |
| 3 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_1.25u | SW75, SW76, SW77 |
| 2 | 2M | Resistor_SMD:R_0603_1608Metric | R7, R9 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | AO3407 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_1.50u | SW32, SW45 |
| 2 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_2.25u | SW59, SW61 |
| 2 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_1.75u | SW47, SW72 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 1N5819 | Diode_SMD:D_SOD-323F | D100 |
| 1 | 32768kHz | Crystal:Crystal_SMD_MicroCrystal_CM9V-T1A-2Pin_1.6x1.0mm_HandSoldering | X1 |
| 1 | 74AHCT125 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U4 |
| 1 | 820K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | Conn_01x02 | Connector_PinSocket_1.27mm:PinSocket_1x02_P1.27mm_Vertical | J3 |
| 1 | Conn_01x04 | nrfmicro:connector_swd | J2 |
| 1 | E73-2G4M08S1C | nrfmicro:E73-2G4M08S1C-52840 | U1 |
| 1 | LOGO | LOGO | G*** |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D200 |
| 1 | RPROG | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW85 |
| 1 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_6.25u | SW78 |
| 1 | SW_Push_45deg | kalih-hotswap:SW_Hotswap_Kailh_MX_2.00u | SW30 |
| 1 | TP4054 | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | TestPoint | TestPoint:TestPoint_THTPad_1.0x1.0mm_Drill0.5mm | RESET |
| 1 | USB-C USB 2.0 MC-372 | nrfmicro:USB-C_C168688 | J1 |
The 275 most common of 279 parts.
Similar boards
- 2 layers18.1 × 33.3 mm

- 2 layers76.3 × 125 mm

- 2 layers133 × 114.7 mm

- 2 layers226 × 94.2 mm

Calcite60
siderakb/calcite
60/52 keys Kailh Choc V1 low profile switches ortho keyboard
196 parts12CERN-OHL-P-2.0 - 2 layers215.1 × 85 mm

Le oeuf
eggsworks/le-oeuf-v2
An ultra-low profile (Kailh PG1316S) keyboard inspired by Le Chiffre.
110 parts8CERN-OHL-S-2.0 - 2 layers225 × 74.8 mm

- 2 layers219.4 × 78 mm

- 2 layers53.3 × 24.1 mm

NumDisciplineBLE
ericrlau/NumDisciplineBLE
BLE Breakout Board To Replace ATMega Used In NumDiscipline
20 partsGPL-3.0
Questions
How big is the Nrfmicro PCB?
It measures 305.8 × 120.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Nrfmicro use?
279 parts, built around the 74AHCT125D, E73-2G4M08S1C, AP2112K-3.3 and TP4054. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Nrfmicro KiCad files?
From the hashim-cpro/ultimate-keyboard repository on GitHub, at the commit this page was made from: the board is hardware/nrfmicro.kicad_pcb and its schematic hardware/MicroNano.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Nrfmicro design in my own project?
Its repository states no licence, so its author keeps all rights: ask hashim-cpro before reusing the design.




