

BoostCore Module
1.5V–28V DC-DC Step-Up Boost Converter Module
- Size
- 19.7 × 46.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 27
- Nets
- 15
- Pads
- 61
- Tracks, vias
- 115, 11
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 May 2026
- Updated
- 31 May 2026
Overview
BoostCore Module is an open-source printed circuit board by hamzadenizyilmaz, from the hamzadenizyilmaz/BoostCore-Module repository on GitHub, published under the AGPL-3.0 licence. It is a 2-layer board of 19.7 × 46.3 mm with 27 parts on 15 nets, routed with 115 tracks and 11 vias.
It is built around the MT3608, SS36 and FSMD185-2920-R, with the P4SMAJ5.0_R1_00001 among its other parts. Its parts include 6 resistors, 5 capacitors, 5 diodes, 2 fuses and 1 IC. It belongs with the power boards of this library.
Main components
4MT3608
SOT-23-6-40℃~+85℃ 1 1.2MHz 100uA、1.6mA 2A 2V~24V Adjustable Boost Boost Built-in No SOT-23-6 DC-DC Converters ROHS西安航天民芯DC-DC ConvertersSS36
SMA(DO-214AC)-55℃~+125℃ 3A 500uA@60V 60V 700mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky DiodesFSMD185-2920-R
2920-40℃~+85℃ 0.9mm 1.5W 1.85A 100A 150mΩ 2.5s 3.7A 33V 40mΩ 5.44mm 7.98mm 2920 Resettable Fuses ROHSFuzetec TechResettable FusesP4SMAJ5.0_R1_00001
SMA(DO-214AC)-55℃~+150℃ 400W@10/1000us 43.5A@10/1000us 5V 6.4V 800uA 9.6V IEC 61000-4-2 TVS SMA(DO-214AC) ESD and Surge Protection (TVS/ESD) ROHSPANJIT InternationalESD And Surge Protection (TVS/ESD)
README
README.mdBoostCore-Module
BoostCore-Module is a compact adjustable DC-DC step-up boost converter module built around the MT3608 regulator.
It supports USB-C 5V input, an optional external VIN input, Schottky OR-ing input selection, resettable fuse protection, TVS protection on USB VBUS, and a trimpot-adjustable output feedback network.
PCB manufacturing sponsor: This project is sponsored by PCBWay.
PCBWay support is mentioned in the documentation because the PCB is intended to be published as an open hardware project and manufactured as a compact prototype board.
Project Highlights
- MT3608 based boost converter
- USB-C power-only input
- External VIN input
- Input OR-ing with SS36 Schottky diodes
- USB-C VBUS protection with 5V TVS diode
- USB-C PTC fuse protection
- Optional VIN_EXT PTC fuse protection
- Adjustable output voltage using trimpot
- 0805 resistor/LED-friendly design choices
- Test points for VIN, VOUT, FB, EN and GND
- KiCad-ready hardware folder structure
- GitHub documentation package with BOM, assembly, layout and testing guides
Sponsorship
This project is sponsored by PCBWay.
PCBWay is mentioned here as the PCB manufacturing sponsor for the open hardware release of BoostCore-Module. The board was designed with prototype manufacturing in mind, including compact routing, silkscreen labels, test points, and an export-ready project structure.
Electrical Overview
| Parameter | Value |
|---|---|
| Controller IC | MT3608 |
| Topology | Boost / step-up |
| USB-C input | 5V only |
| External VIN input | 2V-24V target range |
| Output voltage | Adjustable by RV1 trimpot |
| Switching frequency | MT3608 typical 1.2MHz |
| Inductor | 4.7uH recommended |
| Main boost diode | SS36, 3A, 60V |
| Output adjustment | R1 + R2 + RV1 feedback network |
| Output capacitor caution | Use 50V capacitors for high output voltage |
Current Feedback Network
The adjustable output stage is:
VOUT -> R2 10k -> RV1 100k trimpot -> FB -> R1 2.2k -> GNDRecommended trimpot wiring:
RV1 pin 3 -> R2 side
RV1 pin 1 + pin 2 -> FB nodeFormula:
VOUT = 0.6 x (1 + R_UPPER / R1)Where:
R_UPPER = R2 + active RV1 resistance
R1 = 2.2kImportant:
- Start with the trimpot at the lowest output setting.
- Always adjust output using a multimeter.
- Do not connect a sensitive load before confirming VOUT.
- High output voltages require output capacitors rated above the selected voltage.
Images
Layout preview

Important Hardware Notes
USB-C input
The USB-C connector is used as a 5V power-only input.
Required CC resistors:
CC1 -> 5.1k -> GND
CC2 -> 5.1k -> GNDUSB-PD negotiation is not implemented. The USB-C input is therefore 5V only.
F1 USB fuse
Current selected part:
F1 = KLM3S300RY
PTC resettable fuse
1206 / 3A / 6V
USB-C 5V input onlyDo not use this part on the 24V external input path.
F2 external VIN fuse
Compact option:
F2 = MF-MSMF110/24X-2
1812 / 1.1A / 24VHigher-current but larger option:
F2_ALT = FSMD185-2920-R
2920 / 1.85A / 33VD2 USB TVS
D2 must be a 5V TVS diode, not a Schottky diode.
Recommended:
D2 = P4SMAJ5.0_R1_00001D1 / D3 / D4
The board uses SS36 diodes:
D1 = SS36
D3 = SS36
D4 = SS36D3 and D4 are used for input OR-ing.
C4 polarity
If using the compact electrolytic output capacitor:
C4 (+) -> VOUT
C4 (-) -> GNDMark polarity clearly on silkscreen.
PCB Layout Rules
Boost converters are layout-sensitive. Follow these rules:
- Keep the SW node as short and small as possible.
- The SW node is:
text U1 pin 1 SW + L1 right side + D1 anode - Do not place copper pour under the SW node area.
- Keep FB trace away from SW node, diode switching node and inductor.
- Place C1 close to U1 IN and GND.
- Place output capacitors close to D1 cathode and GND.
- Use a solid GND plane on the bottom layer.
- Add via stitching near high-current GND return paths.
- Do not route feedback under the inductor.
- Make VIN_SYS and VOUT traces wide.
Assembly Order
Recommended assembly sequence:
- Inspect PCB visually.
- Solder USB-C connector.
- Solder protection parts: F1, D2, D3, D4.
- Solder MT3608.
- Solder inductor L1 and diode D1.
- Solder resistors and small capacitors.
- Solder RV1 trimpot.
- Solder output capacitors.
- Solder connectors.
- Inspect polarity of C4.
- Check shorts between VIN, VOUT and GND.
- Power on without load.
- Adjust output voltage with a multimeter.
- Test with a dummy load.
First Power-Up Checklist
Before applying power:
- Check USB-C VBUS is not shorted to GND.
- Check VIN_SYS is not shorted to GND.
- Check VOUT is not shorted to GND.
- Confirm D1 cathode points to VOUT.
- Confirm C4 polarity.
- Confirm RV1 pin 1+2 go to FB.
- Confirm RV1 pin 3 goes to R2.
- Confirm EN is pulled to VIN_SYS through R6.
Initial test:
1. Apply input power.
2. Measure VIN_SYS.
3. Measure VOUT.
4. Adjust RV1 slowly.
5. Verify output under light load.
6. Check temperature of MT3608, L1 and D1.License
Released as open hardware documentation. See LICENSE.
Disclaimer
This is an open hardware project. Use at your own risk. Verify all footprints, ratings, clearances, capacitor voltage ratings and component stock before fabrication or ordering.
Parts
27| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | SS36 | Diode_SMD:D_SMA | D1, D3, D4 |
| 2 | 22µF/50V/X7R | Capacitor_SMD:C_1210_3225Metric | C2, C3 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R4 |
| 2 | VIN_IN | TestPoint:TestPoint_THTPad_3.0x3.0mm_Drill1.5mm | VIN-, VIN+ |
| 1 | (GND) | TestPoint:TestPoint_THTPad_3.0x3.0mm_Drill1.5mm | VOUT- |
| 1 | (VOUT) | TestPoint:TestPoint_THTPad_3.0x3.0mm_Drill1.5mm | TP_VOUT2 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6 |
| 1 | 100k | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV1 |
| 1 | 100nF/50V/X7R | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | 2.2k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | 4.7 µH | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L1 |
| 1 | 47pF/50V/X7R | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | FSMD185-2920-R | Fuse:Fuse_2920_7451Metric | F2 |
| 1 | KLM3S300RY FUSE | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | MRS-050V100ME054-T/R | Capacitor_SMD:CP_Elec_6.3x5.4 | C4 |
| 1 | MT3608 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | P4SMAJ5.0_R1_00001 | Diode_SMD:D_SMA | D2 |
| 1 | PWR_LED | LED_SMD:LED_0805_2012Metric | D5 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_Horizontal | J1 |
The 26 most common of 27 parts.
Similar boards
- 4 layers160.7 × 51.7 mm

- 2 layers50.5 × 47.5 mm

Diy led spot step3
FaisalHussain95/esp32-espnow-led-spots
DIY 220VAC LED spot controller — ESP32-C3 + COB LED + PT4115 PWM dimming, NTC thermal protection, active fan cooling, ESP-NOW mesh. WiFi bridge for Home Assistant (MQTT).
37 parts - 2 layers46.4 × 46.4 mm

- 2 layers168.9 × 123.3 mm

OEM ECU
aeonSolutions/AeonLabs-AI-Volvo-MKII-Open-Hardware
Volvo MKII Open Hardware
296 parts161CC0-1.0 - 2 layers76.8 × 23.5 mm

SommerESP
exico91/SommerESP
A plug and play ESP32-C3 board to control Sommer garage doors
41 parts29MIT - 4 layers159 × 130 mm

- 2 layers

- 2 layers44 × 44 mm

Questions
How big is the BoostCore Module PCB?
It measures 19.7 × 46.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the BoostCore Module use?
27 parts, built around the MT3608, SS36, FSMD185-2920-R and P4SMAJ5.0_R1_00001. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BoostCore Module KiCad files?
From the hamzadenizyilmaz/BoostCore-Module repository on GitHub, at the commit this page was made from: the board is hardware/kicad/BoostCore Module.kicad_pcb and its schematic hardware/kicad/BoostCore Module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BoostCore Module design in my own project?
Its repository publishes it under the AGPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).