Skip to the content
2 layers20 × 20 mmBjt amp, the printed circuit board in 3D

Cheap and simple setup for learning RF electronics

Size
20 × 20 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
11
Pads
50
Tracks, vias
44, 106
Pours
2
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
6 Mar 2022
Updated
19 Aug 2023

Overview

Bjt amp is an open-source printed circuit board by Halogenek, from the Halogenek/modular-rf-bench repository on GitHub. It is a 2-layer board of 20 × 20 mm with 27 parts on 11 nets, routed with 44 tracks and 106 vias.

Its parts include 10 resistors, 6 capacitors, 3 connectors, 2 inductors and 1 transistor. It belongs with the radio and wireless and audio and music boards of this library.

README

README.md

Modular RF Bench

I came across an awesome system for rapid prototyping RF and Microwave solutions by connecting individual components on small PCBs, just like LEGO. This Modular building block system for RF and microwave design of prototypes is in my opinion a very clever way of building RF circuits. On their website the sell almost every available modern RF IC or passive network in a form of a rectangle PCBs. X-Microwave component photo

The whole system is well polished and every part has some sort of improvement. For example the boards interconnection has a ground cutout, probably for better impedance matching. The connection is done (according to their patent) with a small piece with diamond particles that improve contact. That's why they claim that this system can be used up to ~67 GHz.

Of course this performance comes at a price.

My own design

I liked this idea so much that I wanted to check how bad will standard FR4 boards perform if someone would make a system like this one. But without all those whistles.

So I made ten different designs inspired by that system. Ordered it on PcbWay. And when will it arrive I will test it with my VNA. X-Microwave component photo


After some time the boards arrived in decent quality. I soldered SMA connectors to two boards designed for them and screwed them to the PCB base, together with a small interconnecting PCB.

I tried to follow X Microwave design but my idea had some problems. The small board with the number 011 that was designed to connect other boards didn't make good contact after mounted with screws. It just bulged up and the center signal trace didn't touched the traces on the other PCBs. But after adding a small amount of solder to the trace it started to work.

All ordered boards Coax to coax connection Transmission line measurement

Measurements

Measurements of two connected SMA adapters done on nanoVNA.

S11 50 Ohm termination S11 measurement S11 50 Ohm termination by Port 2 of nanoVNA S11 measurement

Measurements of two connected SMA adapters done on better VNA.

S11 50 Ohm termination S11 measurement S11 50 Ohm termination by Port 2 of VNA S11 measurement S21 S21 measurement

I wasn't excepting much after 0,8 mm FR4 PCB but it is usable up to 1,5 GHz. The board to board connection is working and everything is pretty durable.

Parts

27
QtyValueFootprintReferences
6ZResistor_SMD:R_0603_1608MetricR1, R2, R3, R8, R9, R10
4M2modular-rf-bench-footprints:M2-holeH1, H2, H3, H4
2100pCapacitor_SMD:C_0603_1608MetricC4, C6
2Conn_01x02modular-rf-bench-footprints:edge-connectorJ2, J3
1100nCapacitor_SMD:C_0603_1608MetricC3
11µCapacitor_SMD:C_0603_1608MetricC2
1CINCapacitor_SMD:C_0603_1608MetricC1
1COUTCapacitor_SMD:C_0603_1608MetricC5
1Conn_01x01Connector_Wire:SolderWire-0.25sqmm_1x01_D0.65mm_OD1.7mmJ1
1LBInductor_SMD:L_0603_1608MetricL2
1LOGOLOGOG***
1LPInductor_SMD:L_0603_1608MetricL1
1Q_NPN_BECPackage_TO_SOT_SMD:SOT-23Q1
1RB1Resistor_SMD:R_0603_1608MetricR5
1RB2Resistor_SMD:R_0603_1608MetricR4
1RCResistor_SMD:R_0603_1608MetricR6
1REResistor_SMD:R_0603_1608MetricR7

More from Halogenek/modular-rf-bench

11
  • 2 layers30 × 20 mmFilter, the printed circuit board in 3D

    Filter

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    21 parts3
  • 2 layers99 × 20 mm014-base power board, the printed circuit board in 3D

    014-base power board

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    17 parts3
  • 2 layers20 × 20 mm017-johnson counter, the printed circuit board in 3D

    017-johnson counter

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    14 parts3
  • 2 layers15 × 20 mmAmplifier, the printed circuit board in 3D

    Amplifier

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    12 parts3
  • 2 layers20 × 20 mm018-crystal oscillator, the printed circuit board in 3D

    018-crystal oscillator

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    11 parts3
  • 2 layers20 × 20 mmMixer, the printed circuit board in 3D

    Mixer

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    8 parts3
  • 2 layers15 × 20 mmSma connector, the printed circuit board in 3D

    Sma connector

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    7 parts3
  • 2 layers20 × 20 mmPcb turn-45, the printed circuit board in 3D

    Pcb turn-45

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    7 parts3
  • 2 layers10 × 20 mmLoad, the printed circuit board in 3D

    Load

    Halogenek/modular-rf-bench

    Cheap and simple setup for learning RF electronics

    7 parts3

Similar boards

  • 2 layers47.6 × 27.3 mmMmc usb 1, the printed circuit board in 3D

    Mmc usb 1

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    27 parts1.2k
  • 2 layers77.4 × 77.4 mmCORAZON LEDS CON FADE, the printed circuit board in 3D

    CORAZON LEDS CON FADE

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    27 parts915
  • 2 layers44.2 × 29.3 mmI2c tiny usb, the printed circuit board in 3D

    I2c tiny usb

    harbaum/I2C-Tiny-USB

    Cheap and simple I²C to USB interface

    27 parts454
  • 2 layers22 × 42 mmNvme bm to e, the printed circuit board in 3D

    Nvme bm to e

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    27 parts253GPL-3.0
  • 2 layers80 × 61 mmPicoProducer, the printed circuit board in 3D

    PicoProducer

    pjgpetecodes/pico-streamdeck

    This project is an OBS Controller using a Raspberry Pi Pico and CircuitPython.

    27 parts230MIT
  • 2 layers186 × 45 mmAddOnD, the printed circuit board in 3D

    AddOnD

    freeDSP/freeDSP-aurora

    freeDSP ADAU1452 with 8 analog input, 8 analog outputs, S/P-DIF I/O, ADAT I/O, USB Audio Class2, WiFi, Bluetooth

    27 parts226CC-BY-SA-4.0
  • 2 layers29.6 × 40.6 mmDbwifi revB, the printed circuit board in 3D

    Dbwifi revB

    ugcs/ddc

    Drone Show Software is software designed for drone shows, allowing flight path planning as well as control of dozens of drones simultaneously in a synchronized manner.

    27 parts223

Questions

How big is the Bjt amp PCB?

It measures 20 × 20 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Bjt amp use?

27 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bjt amp KiCad files?

From the Halogenek/modular-rf-bench repository on GitHub, at the commit this page was made from: the board is src/bjt-amp/bjt-amp.kicad_pcb and its schematic src/001-base/base.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bjt amp design in my own project?

Its repository states no licence, so its author keeps all rights: ask Halogenek before reusing the design.