Skip to the content
2 layers90.2 × 49.6 mmEsp32, the printed circuit board in 3D

Start by installing the ESP32 board in Arduino IDE https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-mac-and-linux-instructions/ (Mac/Linux)…

Size
90.2 × 49.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
72
Nets
87
Pads
228
Tracks, vias
463, 50
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
8 Oct 2019
Updated
20 Dec 2019

Overview

Esp32 is an open-source printed circuit board by Hackuarium, from the Hackuarium/esp-32wroom repository on GitHub. It is a 2-layer board of 90.2 × 49.6 mm with 72 parts on 87 nets, routed with 463 tracks and 50 vias.

It is built around the ESP32-WROOM-32U, ACT4088US-T and DS18B20, with the PCA9685PW, SI7020-A20-GM and TCS34001FN among its other parts. Its parts include 26 connectors, 16 transistors, 8 resistors, 7 capacitors and 7 ICs. It belongs with the ESP32 boards of this library.

Main components

8

README

README.md
#NameASPIHSI2CTouchUsedRTC
1GND
23V3
3EN
4SENSOR_VP/IO36A0RTC_GPIO0
5SENSOR_VN/IO39A3ChargingRTC_GPIO3
6IO34A6OneWire1RTC_GPIO4
7IO35A7OneWire2RTC_GPIO5
8IO32A4T9Ext3RTC_GPIO9
9IO33A5T8Ext4RTC_GPIO8
10IO25A18 *Ext1RTC_GPIO6
11IO26A19 *Ext2RTC_GPIO7
12IO27A17 *T7ADC batteryRTC_GPIO17
13IO14A16 *HSPICLKHS2_CLKT6BlueRTC_GPIO16
14IO12A15 *HSPIQHS2_DATA2T5RedRTC_GPIO15
15GND
16IO13A14 *HSPIDHS2_DATA3T4GreenRTC_GPIO14
17SHD/SD2SPIHDHS1
18SWP/SD3SPIWP
19SCS/CMDSPICS0
20SCK/CLKSPICLK
21SDO/SD0SPIQ
22SDI/SD1SPID
23IO15A13 *HSPICS0T3WhiteRTC_GPIO13
24IO2A12 *HSPIWPT2RESERVEDRTC_GPIO12
25IO0A11 *T1ProgRTC_GPIO11
26IO4A10 *HSPIHDHS2_DATA1T0OneWire1RTC_GPIO10
27IO16HS1_DATA4
28IO17HS1_DATA5
29IO5VSPICS0HS1_DATA6
30IO18VSPICLKHS1_DATA7Blink LED
31IO19VSPIQ
32NC
33IO21VSPIHDSDASDA
34RXD0RX
35TXD0TX
36IO22VSPIWPSCLSCL
37IO23VSPIDHS1_STROBE
38GND

*: not usable with WIFI

ESP32-Wroom32 datasheet

https://www.espressif.com/sites/default/files/documentation/esp32-wroom-32_datasheet_en.pdf

Official Espressif hardware design guidelines

https://www.espressif.com/sites/default/files/documentation/esp32_hardware_design_guidelines_en.pdf

Really DIY ESP32 board

https://www.instructables.com/id/DIY-ESP32-Development-Board-ESPer/

Programming an ESP32 from Arduino IDE

Start by installing the ESP32 board in Arduino IDE https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-mac-and-linux-instructions/ (Mac/Linux) https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-windows-instructions/ (Windows)

Getting started with ESP32 (including blink example) https://randomnerdtutorials.com/getting-started-with-esp32/

Some debug information https://github.com/espressif/esptool/wiki/ESP32-Boot-Mode-Selection

Flashing board

In Arduino IDE, select "ESP32 Wrover module" (>tools>boards), connect the UART programmer to the board (make sure it is in the right orientation), select the corresponding port (>tools>port). Write a simple sketch (for example blink using pin18 for the red light), and upload it to the board, after seeing the "Connecting..." message in the lower windows of Arduino IDE, press both buttons (PROG and RESET), release the "RESET" button first and then release the "BOOT" button, the upload should start. After this, press reset so that the latest code runs on the board (you should see the red light blinking).

To avoid worrying about pressing the button, connect 10 uF electrolytic capacitor between the EN pin and GND (may work or not depending on boards...) (https://randomnerdtutorials.com/solved-failed-to-connect-to-esp32-timed-out-waiting-for-packet-header/)

Resources

Many ESP32 tutorials/projects are available at Random Nerd Tutorials (web-based, sensor-based, data logging, deep sleep...): https://randomnerdtutorials.com/projects-esp32/

Schema for a dev kit: https://dl.espressif.com/dl/schematics/esp32_devkitc_v4-sch.pdf

Ultra low power tips for ESP32: http://iot-bits.com/ultra-low-power-design-esp32-10-tips/

FreeRTOS

Functions

  • RGBW
  • PCA9685 + 4 x BSP75
  • WS2812 : addressable led
  • Luminosity: TCS3400 or VEML6040 or VEML7700
  • Pressure: MS5637
  • Humidity / Temperature: ChipCAP2 or Si7021
  • Power monitoring

Parts

72
QtyValueFootprintReferences
16ZXMS6004Package_TO_SOT_SMD:SOT-23Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12, Q13, Q14, Q15, Q16
4+12VPAD:pad_0.1x0.3_holeJ2, J11, J17, J22
410kResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR1, R2, R5, R16
4holeMountingHole:MountingHole_3.2mm_M3J5, J6, J7, J8
310uFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC2, C3, C4
2LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD2, D4
2W1PAD:pad_0.1x0.3_holeJ10, J26
1100nFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC1
110µFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC9
116.23kResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR15
122nFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC8
122µFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC13
13.3VTestPoint:TestPoint_2Pads_Pitch2.54mm_Drill0.8mmTP4
14.7kResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR17
14.7µHInductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolderL2
149.9kResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR14
1499Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR4
15 / 12VConnector_BarrelJack:BarrelJack_HorizontalJ1
1ACT4088Package_TO_SOT_SMD:SOT-23-6_HandsolderingU5
1B1PAD:pad_0.1x0.3_holeJ9
1B2PAD:pad_0.1x0.3_holeJ14
1B240ADiode_SMD:D_SOD-123D8
1B3PAD:pad_0.1x0.3_holeJ20
1B4PAD:pad_0.1x0.3_holeJ25
1CONN FT232RLConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ15
1DS18B20Package_TO_SOT_THT:TO-92_InlineU6
1D_SchottkyDiode_SMD:D_SOD-123D3
1ESP32-WROOM-32URF_Module:ESP32-WROOM-32UU1
1G1PAD:pad_0.1x0.3_holeJ4
1G2PAD:pad_0.1x0.3_holeJ13
1G3PAD:pad_0.1x0.3_holeJ19
1G4PAD:pad_0.1x0.3_holeJ24
1MS5637hackuarium:MS5637U2
1PCA9685PWPackage_SO:TSSOP-28_4.4x9.7mm_P0.65mmU4
1PROGButton_Switch_SMD:SW_SPST_PTS645SW2
1R1PAD:pad_0.1x0.3_holeJ3
1R2PAD:pad_0.1x0.3_holeJ12
1R3PAD:pad_0.1x0.3_holeJ18
1R4PAD:pad_0.1x0.3_holeJ23
1RESETButton_Switch_SMD:SW_SPST_PTS645SW1
1Si7020-A20Package_DFN_QFN:DFN-6-1EP_3x3mm_P1mm_EP1.5x2.4mmU3
1TCS3400OptoDevice:Broadcom_DFN-6_2x2mm_P0.65mmU8
1W2PAD:pad_0.1x0.3_holeJ16
1W3PAD:pad_0.1x0.3_holeJ21

More from Hackuarium/esp-32wroom

1
  • 2 layers85 × 75 mmEsp32, the printed circuit board in 3D

    Esp32

    Hackuarium/esp-32wroom

    Start by installing the ESP32 board in Arduino IDE https://randomnerdtutorials.com/installing-the-esp32-board-in-arduino-ide-mac-and-linux-instructions/ (Mac/Linux)…

    74 parts

Similar boards

  • 2 layers100 × 87 mmBertha main, the printed circuit board in 3D

    Bertha main

    Hackuarium/bioreactor

    Please refer to the documentation for all useful information.

    159 parts7
  • 2 layersI2c slave, the printed circuit board in 3D

    I2c slave

    Hackuarium/i2c-slave

    29 parts
  • 2 layers99.9 × 99.9 mmIo base, the printed circuit board in 3D

    Io base

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    98 parts990GPL-3.0
  • 2 layers85 × 75 mmEsp8266, the printed circuit board in 3D

    Esp8266

    Hackuarium/esp-12e

    PWM on all the pins ! HSPI (screen or other): 12 13 14 15 PWM: R12 G15 B13 ADC: TOUT I2C: SCL14 SDA2

    62 parts
  • 2 layers127 × 76.2 mmCkt xing adv, the printed circuit board in 3D

    Ckt xing adv

    IowaScaledEngineering/ckt-xing

    Simple Model Railroad Grade Crossing Controller

    140 parts
  • 2 layers99.9 × 73.7 mmIncubator bottom, the printed circuit board in 3D

    Incubator bottom

    Hackuarium/simple-incubator

    The goal is to create a simple controller of temperature for an incubator.

    57 parts
  • 2 layers57.7 × 50 mmKiCAD Board, the printed circuit board in 3D

    KiCAD Board

    XasWorks/dragon-home

    A rework of our old SmartHome project, this time done cleanly and neatly~

    47 parts8GPL-3.0
  • 4 layers65 × 64 mmPiweather, the printed circuit board in 3D

    Piweather

    pluggee/piweather

    raspberry pi based system for weather monitoring and automation

    60 parts1MIT

Questions

How big is the Esp32 PCB?

It measures 90.2 × 49.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Esp32 use?

72 parts, built around the ESP32-WROOM-32U, ACT4088US-T, DS18B20 and PCA9685PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Esp32 KiCad files?

From the Hackuarium/esp-32wroom repository on GitHub, at the commit this page was made from: the board is rgb/kicad/esp32.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Esp32 design in my own project?

Its repository states no licence, so its author keeps all rights: ask Hackuarium before reusing the design.