Skip to the content
4 layers78 × 36 mmNametag, the printed circuit board in 3D

A simle project to show my name on an e-Paper

Size
78 × 36 mm
Copper layers
4
Thickness
1.6 mm
Parts
71
Nets
78
Pads
240
Tracks, vias
424, 124
Pours
6
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
28 Aug 2024
Updated
29 Aug 2026

Overview

Nametag is an open-source printed circuit board by gumulka, from the gumulka/nametag repository on GitHub. It is a 4-layer board of 78 × 36 mm with 71 parts on 78 nets, routed with 424 tracks and 124 vias.

It is built around the NRF52832-QFAA-R, MBR0530 and AO3401A, with the MLZ1608E100MT000, LQW15AN15NH00D and LQG15HS3N3C02D among its other parts. Its parts include 23 capacitors, 18 resistors, 15 diodes, 4 inductors and 3 transistors. It belongs with the nRF52 and nRF5x boards of this library.

Main components

11

README

README.md

Bluetooth ePaper Nametag

A simle project to show my name on an e-Paper

How to build

If you are new to Zephyr, read the Getting Started Guide. Afterwards you can clone and build this project with:

bash
west init -m https://github.com/gumulka/nametag --mr main nametag
cd nametag
west update
cd epaper_nametag

Bootloader

The bootloader will load and verify the image that is executed. To make it easier to upgrade the device, two images are saved on the device and only one is being executed, while the other is a standby for updating. The bootloader cannot be upgraded via ble, but the image can be. Therefore making it possible to upgrade devices in the field.

If you have a unprogrammed device, use this to build and flash the bootloader:

bash
west build -p -b epaper_nametag -d build_mcuboot ../bootloader/mcuboot/boot/zephyr/ -- -DCONFIG_BOOT_SIGNATURE_TYPE_ECDSA_P256=y
west flash -d build_mcuboot

Application

The application is different from the bootloader and is what is in need of updates/upgrades.

bash
west build -p -b epaper_nametag app -- -DOVERLAY_CONFIG="output.conf"
west flash

Update via BLE

If you have an already running device and just want to upgrade to the latest firmware.

Either with the nRF Connect App, which can be quite handy, or in the commandline use these steps:

bash
sudo mcumgr --conntype ble --connstring ctlr_name=hci0,peer_name='Nametag' image upload build/zephyr/zephyr.signed.bin
sudo mcumgr --conntype ble --connstring ctlr_name=hci0,peer_name='Nametag' image list

Use the second hash provided from the second command to alter the following:

bash
sudo mcumgr --conntype ble --connstring ctlr_name=hci0,peer_name='Nametag' image test "HASH_FROM_OUTPUT"
sudo mcumgr --conntype ble --connstring ctlr_name=hci0,peer_name='Nametag' reset
# wait for the system to restart and if you are sure, that the update was successful then
sudo mcumgr  --conntype ble --connstring ctlr_name=hci0,peer_name='Nametag' image confirm "HASH_FROM_OUTPUT"

More information about the general procedure can be found here and here

[!TIP] I have seen a few errors when trying to upload the image and found that it works best, if I cancel the upload command after a few seconds and restart it a few seconds later, basically splitting the upload into 4-5 chunks instead of uploading it as a whole.

Parts

71
QtyValueFootprintReferences
11LEDg-LED_SMD:LTST-C230D4, D6, D7, D8, D9, D10, D12, D13, D14, D20, D25
11RResistor_SMD:R_0603_1608MetricR8, R9, R10, R11, R12, R13, R14, R16, R17, R18, R24
91uFCapacitor_SMD:C_0603_1608MetricC3, C4, C5, C6, C7, C8, C9, C10, C20
6100nFCapacitor_SMD:C_0402_1005MetricC2, C15, C16, C17, C18, C23
4100kResistor_SMD:R_0603_1608MetricR3, R4, R6, R7
3MBR0530Diode_SMD:D_SOD-123D1, D2, D3
2100pFCapacitor_SMD:C_0402_1005MetricC21, C22
212pFCapacitor_SMD:C_0402_1005MetricC24, C25
24.7uFCapacitor_SMD:C_0603_1608MetricC11, C19
2AO3401APackage_TO_SOT_SMD:SOT-23Q2, Q3
110kResistor_SMD:R_0603_1608MetricR2
110uFCapacitor_SMD:C_0603_1608MetricC1
110uHInductor_SMD:L_0603_1608MetricL4
115nHInductor_SMD:L_0402_1005MetricL3
11KResistor_SMD:R_0603_1608MetricR5
11pFCapacitor_SMD:C_0402_1005MetricC26
12.67RResistor_SMD:R_0603_1608MetricR1
13.3nHInductor_SMD:L_0402_1005MetricL5
13034Battery:BatteryHolder_Keystone_3034_1x20mmBT2
168uHInductor_SMD:L_1210_3225MetricL1
1Crystal_GND24Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY2
1FPC24 0.5mmg-Connector_FPC:AMPHENOL_SFV24R-4STBE1HLFJ2
1MountingHole_Pad_MPg-Misc:Safety-pinH1
1PCB-AntennaRF_Antenna:Texas_SWRA117D_2.4GHz_RightAE2
1Prog HeaderConnector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_VerticalJ3
1STATUS_LEDLED_SMD:LED_0603_1608MetricD5
1SW_PushButton_Switch_SMD:SW_SPST_TL3342SW2
1Si1308EDLPackage_TO_SOT_SMD:SOT-323_SC-70Q1
1nRF52832-QFxxPackage_DFN_QFN:QFN-48-1EP_6x6mm_P0.4mm_EP4.6x4.6mmU2

Similar boards

  • 4 layers20 × 61.5 mmBle door sensor, the printed circuit board in 3D

    Ble door sensor

    gumulka/ble_door_sensor

    A simple project to observe a window or door is open/closed. It works like most other sensors as well. A magnet has to get attached to the door and if it comes near the board, it is detected and the state of the window…

    41 parts2Apache-2.0
  • 2 layers69.4 × 113 mmEpaper reader hw, the printed circuit board in 3D

    Epaper reader hw

    mathias4833/epaper-reader-hw

    An open-source e-paper reader

    126 parts75CERN-OHL-W-2.0
  • 4 layers74.1 × 130 mmBadge secsea V1 1, the printed circuit board in 3D

    Badge secsea V1 1

    cchaloin/HIP_SecSea

    Hack In Provence badge for SecSea

    132 parts
  • 2 layers38.7 × 50.6 mmSmartWatch, the printed circuit board in 3D

    SmartWatch

    PierceMckinnon/SmartWatch

    PCB + SW to make a functional smartwatch

    89 parts1
  • 6 layers57 × 25.9 mmR7FS7MOD, the printed circuit board in 3D

    R7FS7MOD

    Brazil-L/Lumeward-OpenSource

    Open-source Lumeward firmware and development tools

    228 parts2Apache-2.0
  • 4 layers42 × 42 mmExa tim, the printed circuit board in 3D

    Exa tim

    hasenbanck/exa_tim

    EXA_tim is a wrist watch PCB with GNSS time synchronization and e-paper display

    53 parts6
  • 2 layers63.2 × 85 mmBadge blob, the printed circuit board in 3D

    Badge blob

    HeyPCB/badge-blob

    Blob, the social battery badge: The name badge that tells people whether to come say hi. KiCad 10, heypcb.ai merch.

    18 partsCERN-OHL-S-2.0

Questions

How big is the Nametag PCB?

It measures 78 × 36 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Nametag use?

71 parts, built around the NRF52832-QFAA-R, MBR0530, AO3401A and MLZ1608E100MT000. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Nametag KiCad files?

From the gumulka/nametag repository on GitHub, at the commit this page was made from: the board is kicad/nametag.kicad_pcb and its schematic kicad/nametag.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Nametag design in my own project?

Its repository states no licence, so its author keeps all rights: ask gumulka before reusing the design.