Skip to the content
2 layers36 × 23 mmZx81 composite mod, the printed circuit board in 3D

PCB that implements the ZX81 composite mod including the backporch signal for older versions

Size
36 × 23 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
12
Pads
38
Tracks, vias
60, 3
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
21 Nov 2021
Updated
21 Nov 2021

Overview

Zx81 composite mod is an open-source printed circuit board by gpimblott, from the gpimblott/ZX81-Composite-mod-PCB repository on GitHub, published under the MIT licence. It is a 2-layer board of 36 × 23 mm with 17 parts on 12 nets, routed with 60 tracks and 3 vias.

It is built around the NE555P and PN2222A. Its parts include 4 capacitors, 4 resistors, 4 connectors, 2 diodes and 2 transistors.

Main components

2

README

README.md

ZX81-Composite-mod-PCB

PCB that implements the ZX81 composite mod including the backporch signal for older versions

The PCB KiKad files in this repo implement a composite mod board for the ZX81 as described here. More details can also be found on the excellent joulespercoulomb YouTube video.

If the backporch signal is not required then the 555 timer chip can be omitted. I have used this on two ZX81's without the 555 and it results in a much better picture than the frequently described transistor mod alone.

NOTE : This is V2 of the board. V1 had a small error requiring a patch wire and track to be cut. I have not yet had v2 manufactured and tested.

Parts list

The following components are needed to complete the PCB

  • R1,R2 - 10K Resistor
  • R3 - 68 Resistor
  • R4 - 56 Resistor
  • C1 - 22uF electrolytic capacitor
  • C2 - 10nF ceramic disc capacitor
  • C3 - 820pF ceramic disc capacitor
  • C4 - 82pF ceramic disc capacitor
  • Q1,Q2 - 2N2222 transistor
  • D1,D2 - 1N4148 signal diodes
  • U1 - NE555 Timer (Optional)

Fitting the board

The board is redesigned to fit inside the existing housing once the original modulator has been removed. This is done by desoldering the 5v and video signal wires entering the metal casing from the mother board then desoldering the large casing anchors. Once this is done you should be able to remove the modulator. The bottom can then be removed. Once this is done the ground bridges will need to be desoldered anchoring the PCB into the case. The signal wire from the PCB to the composite output jack will also need to be desoldered.

Getting it free can be pain and worse if you want to keep the original modulator in one piece. Once removed the new PCB can be inserted and connected to the necessary locations

  • 5v to the motherboard (same as the original)
  • Video in to the motherboard (same as the original)
  • Video out to the centre of the jack
  • Ground to the modulator casing (don't forget to use the underside pads to anchor the PCB into the casing (and earth the PCB)

Parts

17
QtyValueFootprintReferences
210KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R2
21N4148Diode_THT:D_T-1_P5.08mm_HorizontalD1, D2
2PN2222APackage_TO_SOT_THT:TO-92_InlineQ1, Q2
1 Video_outConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mmJ3
1+5vConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mmJ1
110nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC2
122uFCapacitor_THT:CP_Radial_D4.0mm_P2.00mmC1
156Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR4
168Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3
1820pFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC3
182pFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC4
1GNDConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mmJ4
1NE555PPackage_DIP:DIP-8_W7.62mmU1
1Video_inConnector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mmJ2

Similar boards

  • 2 layers152.9 × 74.9 mmClock, the printed circuit board in 3D

    Clock

    erikvanzijst/clock

    24H digital quartz clock from scratch

    82 parts21
  • 2 layers101.6 × 101.6 mmSurelythiswillbefixed, the printed circuit board in 3D

    Surelythiswillbefixed

    elamrobert443/alternating-led-heart-pcb

    Custom KiCad PCB featuring alternating red and white LED arrays driven by a 555 timer and transistor switching circuits.

    67 parts
  • 2 layers101.6 × 71.1 mmPhase xVer5.0, the printed circuit board in 3D

    Phase xVer5.0

    f5vmr/QRM_Eliminator

    A mistake in the downloaded zip file!! The PCB is not designed with Diptrace but with KiCad and the version it was made with can be down loaded free from here -…

    68 parts
  • 2 layersSimple Curve Tracer, the printed circuit board in 3D

    Simple Curve Tracer

    jakeson21/Small-KiCAD-Projects

    Collection of one-off KiCAD projects

    36 partsGPL-3.0
  • 2 layers117.2 × 115.1 mmExED, the printed circuit board in 3D

    ExED

    lucaci32u4/ExED

    Extended Digital Electronics Laboratory

    136 partsGPL-3.0
  • 2 layers152.4 × 101.6 mm8088-FE2010A SBC, the printed circuit board in 3D

    8088-FE2010A SBC

    skiselev/micro_8088

    Micro 8088 - IBM XT Compatible Processor Board based on Faraday FE2010 chipset

    72 parts412GPL-3.0
  • 2 layers33.7 × 66 mmSmartbell, the printed circuit board in 3D

    Smartbell

    Staacks/there.oughta.be

    Projects featured on my blog at https://there.oughta.be

    27 parts108GPL-3.0

Questions

How big is the Zx81 composite mod PCB?

It measures 36 × 23 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Zx81 composite mod use?

17 parts, built around the NE555P and PN2222A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Zx81 composite mod KiCad files?

From the gpimblott/ZX81-Composite-mod-PCB repository on GitHub, at the commit this page was made from: the board is zx81_composite_mod.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Zx81 composite mod design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).