
Temperature Monitoring Dev Board
tsokomalusi/Temperature-Dev-Board
PCB Skool Community PCB Design Challenge

Kicad design for Pixhawk 4 flight board to CAN network adapter
Ahrs can adapter is an open-source printed circuit board by gpgreen, from the gpgreen/ahrs-can-adapter repository on GitHub, published under the MIT licence. It is a 2-layer board of 61.3 × 77 mm with 44 parts on 74 nets, routed with 333 tracks and 79 vias.
It is built around the STM32F107RCT6 and UA78M33CDCYR. Its parts include 12 capacitors, 7 ICs, 5 resistors, 4 diodes and 4 connectors. It belongs with the interfaces and adapters boards and the STM32 boards of this library.
KiCad design for a CAN adapter to a Dronecad flight board. The MCU is a stm32f107rbt6.
I have put test points on the board, so that pogo pins can be used to program the MCU.
**** 20 Pin connector for JTAG
-------
VTref 1|* *|2 NC
nTRST 3|* *|4 GND
TDI 5|* *|6 GND
TMS 7|* *|8 GND
TCK 9|* *|10 GND
RTCK 11|* *|12 GND
TDO 13|* *|14 GND
RESET 15|* *|16 GND*
DBGRQ 17|* *|18 GND*
5V Supply 19|* *|20 GND*
-------From a 20pin JTAG connector, run wires to the following test pads to connect a debugger:
VTRef 1 <-> 3V3
SWDIO 7 <-> SWD
SWCLK 9 <-> SWC
RESET 15 <-> RST
GND 4 <-> GNDRun the JLink GDB server via the following:
JLinkGDBServer -if SWD -device STM32F103CBGDB can be connected via the following:
gdb-multiarch --command=jlink-stm32.gdb target/thumbv7m/debug/mainopenocd -f interface/stlink-v3.cfg -f target/stm32f1x.cfgas always, thanks for the good work
Licensed under
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 1uF | Capacitor_SMD:C_0603_1608Metric | C3, C4, C7, C8, C9, C10, C11 |
| 4 | MountingHole | MountingHole:MountingHole_2.5mm_Pad | H1, H2, H3, H4 |
| 3 | 1K | Resistor_SMD:R_0603_1608Metric | R2, R4, R5 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric | C5, C6 |
| 2 | LTC2875-S8 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3, U6 |
| 2 | VCAN26A2 | Package_TO_SOT_SMD:SOT-323_SC-70 | U5, U7 |
| 1 | 0.1uf | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 0.33uf | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_HandSolder | C13 |
| 1 | 1.5K | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 10K | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 10uf | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_HandSolder | C14 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D2.0mm | TP1 |
| 1 | 8MHz | Crystal:Crystal_SMD_TXC_7M-4Pin_3.2x2.5mm | Y1 |
| 1 | CAN IN | Connector_Dsub:DSUB-9_Socket_Horizontal_P2.77x2.84mm_EdgePinOffset14.56mm_Housed_MountingHolesOffset8.20mm | J3 |
| 1 | CAN OUT | Connector_Dsub:DSUB-9_Socket_Horizontal_P2.77x2.84mm_EdgePinOffset14.56mm_Housed_MountingHolesOffset8.20mm | J4 |
| 1 | Flight Power | Connector_JST:JST_GH_BM06B-GHS-TBT_1x06-1MP_P1.25mm_Vertical | J1 |
| 1 | Flight Telem | Connector_JST:JST_GH_BM04B-GHS-TBT_1x04-1MP_P1.25mm_Vertical | J2 |
| 1 | GND | TestPoint:TestPoint_Pad_D2.0mm | TP2 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | LED1 | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | LED2 | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | LED3 | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | MPM3610-adafruit 5V | custom_footprint:Adafruit_MPM3610 | U1 |
| 1 | Polyfuse | Fuse:Fuse_Bourns_MF-SM_7.98x5.44mm | F1 |
| 1 | RST | TestPoint:TestPoint_Pad_D2.0mm | TP5 |
| 1 | Reset | custom_footprint:OnShine KPT-1187B | SW1 |
| 1 | STM32F107RCT6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U4 |
| 1 | SWC | TestPoint:TestPoint_Pad_D2.0mm | TP4 |
| 1 | SWD | TestPoint:TestPoint_Pad_D2.0mm | TP3 |
| 1 | UA78M33CDCYR | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |

tsokomalusi/Temperature-Dev-Board
PCB Skool Community PCB Design Challenge



Prosthetics-Exoskeleton/Grip_Exo_PCB_V1
KiCAD design files for first iteration of grip exoskeleton PCB. Contains 10 sensor ports and space for 5 sets of solenoid valves


sundr007/HotBox
A benchtop thermal Chamber used to test electronics at elevated ambient temperature. Kicad PCB, STM32 firmware, OpenScad Mechanical


It measures 61.3 × 77 mm and has 2 copper layers, 1.6 mm thick.
44 parts, built around the STM32F107RCT6 and UA78M33CDCYR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the gpgreen/ahrs-can-adapter repository on GitHub, at the commit this page was made from: the board is ahrs-can-adapter.kicad_pcb and its schematic ahrs-can-adapter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).