Skip to the content
4 layers80.7 × 78.7 mmOstentus hw, the printed circuit board in 3D

A PCB front panel for Golioth's Aludel hardware platform

Size
80.7 × 78.7 mm
Copper layers
4
Thickness
1.6 mm
Parts
77
Nets
77
Pads
241
Tracks, vias
426, 124
Pours
5
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
4 Jan 2023
Updated
19 Jul 2024

Overview

Ostentus hw is an open-source printed circuit board by golioth, from the golioth/ostentus-hw repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 4-layer board of 80.7 × 78.7 mm with 77 parts on 77 nets, routed with 426 tracks and 124 vias.

It is built around the CAP1203-1-SN, LIS2DH12 and BAV99, with the XZMDKCBDDG45S-9, B340LA and BSS138 among its other parts. Its parts include 30 resistors, 14 capacitors, 8 diodes, 6 connectors and 3 ICs. It belongs with the lEDs and displays boards and the RP2040 boards of this library.

Main components

7

README

README.md

Ostentus

The Ostentus is part of Golioth's "Aludel" platform, a family of devices that makes it easier to connect hardware to the internet using Golioth's Firmware SDK and cloud platform. The Aludel family of devices are widely used in Golioth's Reference Designs, which are end-to-end demonstrations of IoT devices targeted at different vertical applications.

This board acts as a display and input device for Reference Designs. Using a series of simple calls from a Zephyr platform, it's possible to offload readings from the underlying device and push them up to the display without consuming processing cycles on the main processor (such as the nRF9160 on the Elixir). We chose ePaper in order to have a high visibility display that would continue showing a reading when in a low power or off state. Since the QWIIC connector powers the Ostentus as well as sending data, it's possible to power down the entire subsystem of the Ostentus while still operating the underlying Elixir.

This is released as Revision C of the Ostentus.

On the board

  • Raspberry Pi Pico - Originally chosen during the part shortages of 2022-23, the Pico provides a low cost solution including a programming interface over the USB port + micropython ease-of-use
  • ePaper interface
  • Accelerometer (LIS2DH12) -- Currently unimplemented but targeting "double tap" behaviors in the future
  • 3 button capacitive touch controller (CAP-1203-1)
  • QWIIC header for incoming power and i2c
  • Downward firing LEDs

Programming

There are two companion repositories which enable the Ostentus to work:

The Aludel form factor

The Aludel form factor (Originally the "Aludel Mini" form factor) is based around the Bud Boxes CU-1937-MB. This board is designed to affix to the top of this case without the original plastic lid from Bud. The QWIIC connector on backside of the Ostentus is meant to be wired to the Elixir, which has a matching connector.

Rev C Photos

Ostentus_Front_Lit_RevC Ostentus_Back_RevC Ostentus_Front_RevC

Purchase

The Ostentus board is not available to purchase. Please contact devrel@golioth.io if you would like to arrange help with your manufacturing.

Hardware Lineage and License

This design was derived from the Pimoroni Badger 2040

This board is released under the CERN OHL-P (v2) license. See LICENSE for more info.

Any replication or modification of this design must remove references to Golioth and The Golioth Logo, which is a trademark of Golioth, Inc.

Parts

77
QtyValueFootprintReferences
170Resistor_SMD:R_0603_1608MetricR3, R10, R11, R12, R14, R15, R16, R17, R18, R19, R20, R21, R26, R27, R28, R29 +1
61KResistor_SMD:R_0603_1608MetricR8, R9, R22, R23, R24, R25
51UCapacitor_SMD:C_0603_1608MetricC7, C9, C10, C11, C12
40.1UCapacitor_SMD:C_0603_1608MetricC3, C4, C13, C14
4MHMountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4
31K8Resistor_SMD:R_0603_1608MetricR4, R5, R13
34U7Capacitor_SMD:C_0805_2012MetricC5, C6, C8
3cap1203-PADostentus:CAP1203-Pad-OstentusJ4, J5, J6
2500Resistor_SMD:R_0603_1608MetricR6, R7
2BAV99Package_TO_SOT_SMD:SOT-23D7, D8
2LOGOostentus:internet-5mm-1000dpiG***, G***
2TL3342 PushButton_Switch_SMD:SW_SPST_TL3342SW1, SW2
2Test PointTestPoint:TestPoint_Pad_1.5x1.5mmTP2, TP3
2XZMDKCBDDG45S-9ostentus:LED_XZMDKCBDDG45S-9D9, D10
10R47Resistor_SMD:R_0603_1608MetricR2
110KResistor_SMD:R_0603_1608MetricR1
110UCapacitor_SMD:C_0805_2012MetricC1
11UCapacitor_SMD:C_0805_2012MetricC2
1B340LADiode_SMD:D_SMAD6
1BSS138Package_TO_SOT_SMD:SOT-23Q1
1CAP1203-1-SNostentus:SOIC127P600X175-8NU1
1Conn_01x24_FemaleConnector_FFC-FPC:Hirose_FH12-24S-0.5SH_1x24-1MP_P0.50mm_HorizontalJ1
1Conn_ARM_JTAG_SWD_10Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMDJ3
1Greenostentus:XZFBB45S-9D2
1LIS2DH12ostentus:SENSOR_LIS2DH12U3
1LOGOostentus:TheGolioth-7mm-1000dpiG***
1LOGOostentus:battery-5mm-1000dpiG***
1LOGOostentus:power-5mm-1000dpiG***
1LOGOostentus:lightbulb-5mm-1000dpiG***
1NR4018T100MInductor_SMD:L_Taiyo-Yuden_NR-40xxL1
1Picoostentus:RPi_Pico_SMD_TH_PasteU2
1QWIICConnector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_VerticalJ2
1Redostentus:XZFBB45S-9D1
1Yellowostentus:XZFBB45S-9D3

Similar boards

  • 2 layers133 × 114.7 mmBlade right, the printed circuit board in 3D

    Blade right

    ufan/mykeyboard

    A collection of pcb boards designed by me

    106 parts23
  • 2 layers90 × 90 mmSensor bed, the printed circuit board in 3D

    Sensor bed

    ufan/sensor_bed

    A PCB with various kinds of sensors like optical mouse sensor, joystick, encoder, capacitive sliders etc.

    70 parts4
  • 2 layers221 × 221 mmWordclockPCB, the printed circuit board in 3D

    WordclockPCB

    maelgui/wordclock

    This repository contains every files needed to build the clock

    159 parts
  • 2 layers120 × 85 mmLaunch it, the printed circuit board in 3D

    Launch it

    nathaniel-fargo/presentinator

    A fun Christmas PCB game

    100 partsMIT
  • 2 layers61.5 × 126.8 mmBadge eda, the printed circuit board in 3D

    Badge eda

    theparanoids/keyhole-badge

    The Paranoids have designed a sound-reactive LED electronic conference badge for DEFCON 2022. This repository contains the PCB design files for the badge and the source code to the firmware that runs on the…

    88 parts7
  • 4 layers43 × 95 mmOe commutator controller, the printed circuit board in 3D

    Oe commutator controller

    open-ephys/commutators

    Active coaxial commutator for electrophysiology

    92 parts5
  • 4 layers43 × 95 mmOe commutator controller, the printed circuit board in 3D

    Oe commutator controller

    open-ephys/commutator-controller

    Open Ephys commutator PCB and firmware

    107 parts2

Questions

How big is the Ostentus hw PCB?

It measures 80.7 × 78.7 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Ostentus hw use?

77 parts, built around the CAP1203-1-SN, LIS2DH12, BAV99 and XZMDKCBDDG45S-9. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ostentus hw KiCad files?

From the golioth/ostentus-hw repository on GitHub, at the commit this page was made from: the board is ostentus-hw.kicad_pcb and its schematic ostentus-hw.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ostentus hw design in my own project?

Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).