

Beetletriple
Some bits for robots or other control applications
- Size
- 82 × 61 mm
- Copper layers
- 4
- Thickness
- 1.79 mm
- Parts
- 76
- Nets
- 76
- Pads
- 295
- Tracks, vias
- 709, 156
- Pours
- 14
- Routed
- Yes
- KiCad
- KiCad 5 (file 20210126)
- Created
- 18 Mar 2022
- Updated
- 25 Feb 2022
Overview
Beetletriple is an open-source printed circuit board by goktugh, from the goktugh/robotbits repository on GitHub. It is a 4-layer board of 82 × 61 mm with 76 parts on 76 nets, routed with 709 tracks and 156 vias.
It is built around the ATTINY1617-MN, FAN7388MX and TPS54331DR-JSM, with the HT7550-1, 1N4148W and IRF8313PBF among its other parts. Its parts include 20 capacitors, 19 resistors, 10 diodes, 10 connectors and 6 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
8ATTINY1617-MN
QFN-24-EP(4x4)-40℃~+105℃ 1.8V~5.5V 10bit 16KB 20MHz 22 256Byte 2KB 8 Bit 8bit AVR Built-in FLASH VQFN-24-EP(4x4) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)FAN7388MX
SOIC-20-300mil-40℃~+125℃ 10V~20V 160uA 30ns 350mA 50ns 6 650mA IGBT、MOSFET Three Phase Under Voltage Protection SOIC-20-300mil Gate Drivers ROHSonsemiGate DriversTPS54331DR-JSM
SOP-8-40℃~+125℃ 1 2mA 3A 4.5V~40V 400kHz Adjustable Buck Built-in No Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting Step-down type SOP-8 DC-DC Converters ROHSJSMSEMIDC-DC ConvertersHT7550-1
SOT-89-3-40℃~+85℃@(Ta) 1 150mA 2.5uA 25mV@(1mA) 30V 5V Fixed Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSHOLTEKVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching DiodesIRF8313PBF
SO-8-55℃~+175℃ 15.5mΩ@10V 2 N-Channel 2.35V 2W 30V 6nC 760pF 87pF 9.7A SO-8 MOSFETs ROHSInfineon TechnologiesMOSFETsYSPI1040-101M
SMD,11.0x10.1mm-40℃~+125℃ 1.5A 100uH 2A 300mΩ Molded inductor ±20% SMD,11.0x10.1mm Molding Power Inductors ROHSYJYCOINPower InductorsB340A
SMA(DO-214AC)-55℃~+150℃ 1 Independent 3A 40V 500mV@3A 500uA@40V 80A SMA(DO-214AC) Schottky Diodes ROHSDiodes IncorporatedSchottky Diodes
Parts
76| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 2.2uF 50V | Capacitor_SMD:C_1206_3216Metric | C8, C9, C10, C11, C12, C13, C14, C15, C16 |
| 8 | 1.5k | Resistor_SMD:R_0805_2012Metric | R2, R10, R11, R12, R13, R14, R15, R18 |
| 6 | 1N4148W | Diode_SMD:D_SOD-123 | D2, D3, D4, D5, D6, D7 |
| 6 | 4.7R | Resistor_SMD:R_0805_2012Metric | R4, R5, R6, R7, R8, R9 |
| 6 | IRF8313PBF | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q1, Q2, Q3, Q4, Q5, Q6 |
| 4 | 10uF 50V | Capacitor_SMD:C_1206_3216Metric | C1, C2, C6, C7 |
| 3 | 220uF | Capacitor_SMD:C_Elec_10x10.2 | C3, C4, C5 |
| 3 | motor_out | beetletriple:TerminalBlock_motor | J2, J3, J4 |
| 2 | 0.01R shunt | Resistor_SMD:R_2512_6332Metric_Pad1.40x3.35mm_HandSolder | R16, R17 |
| 2 | DNP | Capacitor_SMD:C_1206_3216Metric | C21, C22 |
| 2 | FAN7388MX | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U11, U12 |
| 2 | Green | LED_SMD:LED_0805_2012Metric | D8, D9 |
| 1 | 0.1uF | Capacitor_SMD:C_1206_3216Metric | C18 |
| 1 | 100R | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 10nF | Capacitor_SMD:C_1206_3216Metric | C17 |
| 1 | 10uH | Inductor_SMD:L_12x12mm_H4.5mm | L1 |
| 1 | 20mmx5 fuse holder | beetletriple:fuseholder_flexible | F1 |
| 1 | ATtiny1617-M | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U3 |
| 1 | B340A-13-F | Diode_SMD:D_SMA_Handsoldering | D1 |
| 1 | DNP | Resistor_SMD:R_0805_2012Metric | R23 |
| 1 | HT7550-1 | Package_TO_SOT_SMD:SOT-89-3 | U2 |
| 1 | Orange | LED_SMD:LED_0805_2012Metric | D10 |
| 1 | Power IN | beetletriple:beetlepower | J1 |
| 1 | TPS54331DR | Package_SO:TI_SO-PowerPAD-8_ThermalVias | U1 |
| 1 | input_c1 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | input_c2 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | input_c3 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J7 |
| 1 | output_c4 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8 |
| 1 | output_c5 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J9 |
| 1 | soicbite programming connector | beetletriple:SOIC_clipProgSmall | J10 |
The 72 most common of 76 parts.
More from goktugh/robotbits
12- 2 layers124 × 67 mm

- 2 layers124 × 67 mm

- 4 layers83.5 × 61 mm

- 4 layers82 × 56.5 mm

- 2 layers110 × 48 mm

- 4 layers32 × 58 mm

- 2 layers52 × 52 mm

- 2 layers77 × 39 mm

- 2 layers41 × 39 mm

- 4 layers19 × 32 mm

- 2 layers43.5 × 15 mm

- 2 layers49.6 × 41.3 mm

Similar boards
- 2 layers80 × 35 mm

VORON V2.0-Expander
thebrakshow/VORON-V2.0-Expander
Expansion PCB to add 3 additional stepper drivers and 2 external PWM fans to a standard RAMPS 1.4 shield
37 parts6 - 2 layers29 × 22 mm

5way cv switch
cycfi/5way_cv_switch
KiCad PCB project — part of the Cycfi Connect series (umbrella repo: cycfi/connect)
20 parts - 2 layers30 × 8 mm

Cv buffer
cycfi/cv_buffer
KiCad PCB project — part of the Cycfi Connect series (umbrella repo: cycfi/connect)
11 parts - 2 layers102.8 × 94 mm

Cv pot big panel
cycfi/cv_pot_big
KiCad PCB project — part of the Cycfi Connect series (umbrella repo: cycfi/connect)
721 parts - 2 layers70 × 14 mm

Touch pad
cycfi/touch_pad
KiCad PCB project — part of the Cycfi Connect series (umbrella repo: cycfi/connect)
18 parts - 4 layers120 × 108 mm

- 2 layers65 × 56 mm

Ras pi supercap ups
akuker/SuperUPS
This is a fork of the original Supercapacitor UPS board for a Raspberry Pi by Scott Baker, http://www.smbaker.com/
88 parts7 - 2 layers67 × 45 mm

Questions
How big is the Beetletriple PCB?
It measures 82 × 61 mm and has 4 copper layers, 1.79 mm thick.
What parts does the Beetletriple use?
76 parts, built around the ATTINY1617-MN, FAN7388MX, TPS54331DR-JSM and HT7550-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Beetletriple KiCad files?
From the goktugh/robotbits repository on GitHub, at the commit this page was made from: the board is beetletriple/beetletriple.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Beetletriple design in my own project?
Its repository states no licence, so its author keeps all rights: ask goktugh before reusing the design.