
RH2288 PWM
alphaarea/RH2288V2_FAN_Controller
Limit the annoying fan speed, made it possible to be a quite homeserver.

A simple, yet versatile quadcopter controller and code. Based on the Arduino platform using the Atmega328p and MPU6050.
QMBTv1 is an open-source printed circuit board by glina126, from the glina126/QMBT_copter repository on GitHub, published under the MIT licence. It is a 2-layer board of 24.9 × 29.7 mm with 42 parts on 51 nets, routed with 386 tracks and 29 vias.
It is built around the ATMEGA328P-MMH. Its parts include 13 capacitors, 11 connectors, 8 ICs, 7 resistors and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
A simple, yet versatile quadcopter controller and code. Based on the Arduino platform using the Atmega328p and MPU6050.
##Final Update:
This project is changing direction. The atmega328p microcontroller is simply insufficient for being used as a quadcopter brain.
This is due to a few reasons mainly because - not enough interrupts and 8bit architecture.
The loop runs at a mere 33 miliseconds, which is not sufficient.
Also, due to the lack of interrupts, the precision at which we can sample the RC RX is very low causing noise in the system.
That being said, the project is changing gears and moving on to a much better microcontroller, LPC11U35 Cortex-m0 running at 48mhz.
###This project has a few milestones that are set on its path.
This is just the beginning of the project, though experimentation with the PCB have been conducted for a while now. At this point, the project is reset to a fresh start.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1uF | SMD_Packages:SMD-0402_c | C1, C2, C3, C4, C10, C11 |
| 6 | 1K | Resistors_SMD:R_0402 | R1, R3, R4, R5, R6, R17 |
| 2 | C | SMD_Packages:SMD-0402_c | C7, C8 |
| 2 | LED | footprints:SMD-0402_LED | D1, D5 |
| 2 | MCP1802_(Vreg) | footprints:Sot-23-5 | IC2, IC3 |
| 2 | conn_3x4 | footprints:conn_3x4 | U3, U4 |
| 1 | 10K | Resistors_SMD:R_0402 | R2 |
| 1 | 10nF | SMD_Packages:SMD-0402_c | C9 |
| 1 | 1uF | SMD_Packages:SMD-0402_c | C5 |
| 1 | 2.2nF | SMD_Packages:SMD-0402_c | C12 |
| 1 | 2.2uF | SMD_Packages:SMD-0402_c | C6 |
| 1 | 3V3 | footprints:1x0.5mm_Through_hole2 | P18 |
| 1 | 5V | footprints:1x0.5mm_Through_hole2 | P20 |
| 1 | 6pin_1.27mm | footprints:6pin_1.27mm | C13 |
| 1 | ATMEGA328P-MM | footprints:QFN-28-4x4mm_fixed_mask | IC1 |
| 1 | BSS138DW_array | footprints:BSS138DW_array | U2 |
| 1 | GND | footprints:1x0.5mm_Through_hole2 | P19 |
| 1 | MISO | footprints:1x0.5mm_Through_hole2 | P9 |
| 1 | MOSI | footprints:1x0.5mm_Through_hole2 | P10 |
| 1 | MPU6050 | footprints:MPU6050 | IC4 |
| 1 | RST | footprints:1x0.5mm_Through_hole2 | P12 |
| 1 | SCK | footprints:1x0.5mm_Through_hole2 | P11 |
| 1 | SCL | footprints:1x0.5mm_Through_hole2 | P15 |
| 1 | SDA | footprints:1x0.5mm_Through_hole2 | P14 |
| 1 | SS | footprints:1x0.5mm_Through_hole2 | P16 |
| 1 | SW_PUSH | footprints:switch_tactile_SM10 | SW1 |
| 1 | VCC | Socket_Strips:Socket_Strip_Straight_1x02 | P17 |
| 1 | ceramic_resonator | footprints:ceramic_resonator_smd | U1 |

alphaarea/RH2288V2_FAN_Controller
Limit the annoying fan speed, made it possible to be a quite homeserver.

BenSchZA/decawave-trilateration-hardware
Hardware (Kicad schematics and PCB) for a local vehicle tracking solution using trilateration and Decawave technology.


frankie-eight-days/mochiRadio
A 915MHz radio w/ temp sensor, pressure sensor, LED and ATMega328p




kitspace/component_tester
A keychain version of the Mikrontroller.net AVR component tester
It measures 24.9 × 29.7 mm and has 2 copper layers, 1.6 mm thick.
42 parts, built around the ATMEGA328P-MMH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the glina126/QMBT_copter repository on GitHub, at the commit this page was made from: the board is PCB/QMBTv1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).