

Openmower Brushed
I have rebuilt a Bosch Indego800. It had no RPMSensor on the mowing motor, so i added magnet and hallsensor myself. It is easily possible, to convert any old mower with brushed motors, to openmower with RTK.
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 139
- Nets
- 208
- Pads
- 687
- Tracks, vias
- 10,047, 414
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 11 Sep 2025
- Updated
- 4 May 2026
Overview
Openmower Brushed is an open-source printed circuit board by gk977246, from the gk977246/Openmower_Brushed repository on GitHub. It is a 2-layer board of 100 × 100 mm with 139 parts on 208 nets, routed with 10,047 tracks and 414 vias.
It is built around the 74LVC2G17GW, ARDUINO UNO R3 and INA139NA, with the AMS1117-3.3, BSS138 and WS2812B among its other parts. Its parts include 51 resistors, 20 connectors, 17 capacitors, 16 ICs and 15 diodes. It belongs with the RP2040, STM32 and AVR (ATmega, ATtiny) boards of this library.
Main components
774LVC2G17GW
SOT-363-40℃~+125℃ 1 1.65V~5.5V 10uA 2 24mA 24mA 5.4ns@3.3V,50pF 74LVC Schmitt trigger Unidirectional SOT-363 Buffers, Drivers, Receivers, Transceivers ROHSTECH PUBLICBuffers, Drivers, Receivers, TransceiversARDUINO UNO R3
Arduino UNO R3 Printed Circuit Board ModuleArduinoUncategorisedINA139NA
SOT-23-5SOT-23-5 Battery Management ROHSTexas InstrumentsBattery ManagementAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsWS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedSS8050
SOT-323-55℃~+150℃ 1 NPN 1.5A 100MHz 100nA 200 25V 300mW 500mV 5V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)
README
README.mdThis is a modified PCB(0.13) from https://github.com/ClemensElflein/OpenMower
Openmower for brushed Motors (HallSensors required)
use at your own Risk!
May2026 : Update
I have rebuilt a Bosch Indego800. It had no RPMSensor on the mowing motor, so i added magnet and hallsensor myself. It is easily possible, to convert any old mower with brushed motors, to openmower with RTK.
Just solder the board, and follow the instructions on https://openmower.de/latest/docs/step-by-step/3-software-setup/
Instead of configure Xesc, you just need to flash the stm32g030 (brush_xesc-left and right-mos_xesc-middle).
With OpenmowerOSv2 you can now change all parameters in one config file(without bind-mount).
Openmower-gui also got an update to v2, but it is only working in openmowerOSv1.
Sep.2025:
I wanted to use openmower-gui, so I changed the version in /etc/systemd/system/openmower.service(maybe it will work again soon).
from Discord:
If you delete the prefix releases- before ${OM_VERSION}
in the ExecStartline in the service file you can set an arbitrary tag (e.g. sha-9f65b12)
in /boot/openmower/openmower_version.txt
but you have to prefix e.g. edge with releases- (so releases-edge) there if you want go back,
because you deleted the prefix in the service file.
And maybe you want to change /etc/systemd/system/openmower-debug.service as well to be consistant if you need logs.
Also add this line:
--volume /boot/openmower/yf2040v4rma.yaml:/opt/open_mower_ros/src/open_mower/params/hardware_specific/YardForceSA650/comms_xesc_2040_w_r4ma_params.yaml \
and copy the file to /boot/openmower (to be able to change Rpm,...)
Parts
139| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R5, R8, R27, R29, R31, R43, R44, R45, R46, R47, R48, R49, R50 |
| 10 | 4k7 | Resistor_SMD:R_0603_1608Metric | R13, R14, R15, R16, R17, R18, R35, R36, R37, R38 |
| 7 | 100 | Resistor_SMD:R_0603_1608Metric | R19, R20, R22, R23, R24, R25, R51 |
| 6 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP3, TP4, TP5, TP6 |
| 5 | DNP | Resistor_SMD:R_0603_1608Metric | R7, R30, R32, R39, R40 |
| 5 | D_Schottky | Diode_SMD:D_SMA | D1, D2, D3, D4, D5 |
| 4 | .1uF | Capacitor_SMD:C_0603_1608Metric | C4, C5, C6, C7 |
| 4 | 74LVC2G17 | Package_TO_SOT_SMD:SOT-23-6 | U9, U12, U14, U15 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_5mm_Pad_Via | H1, H2, H3, H4 |
| 3 | 3k3 | Resistor_SMD:R_0603_1608Metric | R10, R11, R12 |
| 3 | 47u | Capacitor_THT:CP_Radial_D10.0mm_P3.50mm | C8, C9, C10 |
| 3 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4, J6, J7 |
| 3 | Conn_01x03_Pin | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J11, J12, J13 |
| 3 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5, J8, J9 |
| 3 | LED GREEN | LED_SMD:LED_0603_1608Metric | D7, D9, D11 |
| 3 | LED RED | LED_SMD:LED_0603_1608Metric | D8, D10, D12 |
| 3 | STM32G031F8Px | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U4, U5, U6 |
| 2 | .2uF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C16, C17 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R1, R4 |
| 2 | 2.49k | Resistor_SMD:R_0603_1608Metric | R33, R34 |
| 2 | 20k | Resistor_SMD:R_0603_1608Metric | R41, R42 |
| 2 | 22n | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric | C2, C3 |
| 2 | 8874 | Package_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask3x3mm_ThermalVias | U10, U11 |
| 2 | Conn_01x04_Pin | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J17, J18 |
| 2 | Fuse | Fuse:Fuseholder_Clip-5x20mm_Eaton_1A5601-01_Inline_P20.80x6.76mm_D1.70mm_Horizontal | F1, F2 |
| 2 | INA139 | Package_TO_SOT_SMD:SOT-23-5 | U1, U8 |
| 1 | 0.003R | Resistor_SMD:R_2512_6332Metric | R3 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C15 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 20 | Resistor_SMD:R_0603_1608Metric | R26 |
| 1 | 20K | Resistor_SMD:R_0603_1608Metric | R21 |
| 1 | 27517 | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | 5/R/T/- | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J20 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Arduino_UNO_R3 | Module:Arduino_UNO_R3 | A1 |
| 1 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q4 |
| 1 | Batt | Connector_Molex:Molex_Mini-Fit_Jr_5566-02A_2x01_P4.20mm_Vertical | J1 |
| 1 | Charge | Connector_Molex:Molex_Mini-Fit_Jr_5566-02A_2x01_P4.20mm_Vertical | J2 |
| 1 | D_Schottky | Diode_SMD:D_SOD-123F | D15 |
| 1 | D_Schottky | Diode_SMD:D_SMB | D13 |
| 1 | Fan | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1 |
| 1 | Gps | 1meine:My_GPS_module | U13 |
| 1 | Jumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | LSM6DSOTR | Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4y | AC1 |
| 1 | M | Connector_Phoenix_MC_HighVoltage:PhoenixContact_MCV_1,5_2-G-5.08_1x02_P5.08mm_Vertical | J10 |
| 1 | Pico | Module_RaspberryPi_Pico:RaspberryPi_Pico_Common | U16 |
| 1 | Q_NMOS_GDS | Package_TO_SOT_SMD:TO-252-2 | Q3 |
| 1 | Q_PMOS_GDS | Package_TO_SOT_SMD:TO-252-2 | Q2 |
| 1 | R | Connector_Phoenix_MC_HighVoltage:PhoenixContact_MCV_1,5_2-G-5.08_1x02_P5.08mm_Vertical | J15 |
| 1 | R020 | Resistor_SMD:R_2512_6332Metric | R28 |
| 1 | Raspberry_Pi_2_3 | 1meine:raspberrypi_2_3 | J16 |
| 1 | Switch | Connector_Molex:Molex_Mini-Fit_Jr_5566-02A_2x01_P4.20mm_Vertical | J3 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D14 |
| 1 | Zener10V | Diode_SMD:D_SOD-123 | D6 |
| 1 | l | Connector_Phoenix_MC_HighVoltage:PhoenixContact_MCV_1,5_2-G-5.08_1x02_P5.08mm_Vertical | J14 |
| 1 | neop. | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J19 |
| 1 | ss8050 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | ~ | 1meine:4015Modul | U2 |
Similar boards
- 2 layers64 × 69.9 mm

- 4 layers90 × 110 mm
.kicad_pcb.jpg?size=s&soon)
- 2 layers

Esp32-module-3.0
sukeshraom/ESP32-WROOM-32E-development-board
ESP32-WROOM-32E development board in the Arduino UNO form factor with USB Type-C and CH340C USB-to-UART interface. Includes complete KiCad schematic, PCB layout, and manufacturing files.
33 parts1 - 2 layers61.7 × 108 mm

Panel pcb
knonyks/onyks-iot-zigbee-panel-sterujacy-z-wyswietlaczem
Panel sterujący z wyświetlaczem
40 parts - 2 layers68.2 × 52.2 mm

Forward Ignition PCB
aditgoyal5/Forward_Ignition_PCB
This repository is about a printed circuit board I built for Team Sammard.
135 parts - 4 layers136 × 95 mm

- 2 layers38 × 56 mm

- 2 layers50 × 50 mm

Rfid uhf wifi reader
OpenLaundry/wifi-rfid-uhf-reader
Portable long range RFID uhf reader with WIFI based on esp32
23 parts8
Questions
How big is the Openmower Brushed PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Openmower Brushed use?
139 parts, built around the 74LVC2G17GW, ARDUINO UNO R3, INA139NA and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Openmower Brushed KiCad files?
From the gk977246/Openmower_Brushed repository on GitHub, at the commit this page was made from: the board is openmower_brushed/OpenMower_brushed.kicad_pcb and its schematic openmower_brushed/Mot.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Openmower Brushed design in my own project?
Its repository states no licence, so its author keeps all rights: ask gk977246 before reusing the design.