

ECP5 FPGA with 8MB PSRAM and extension header
- Size
- 54.6 × 54.6 mm
- Copper layers
- 4
- Thickness
- 1.58 mm
- Parts
- 115
- Nets
- 265
- Pads
- 753
- Tracks, vias
- 1,425, 290
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Jan 2024
- Updated
- 12 Oct 2024
Overview
ECP5 is an open-source printed circuit board by gildobjanschi, from the gildobjanschi/ECP5_BGA381_RISCV repository on GitHub, published under the MIT licence. It is a 4-layer board of 54.6 × 54.6 mm with 115 parts on 265 nets, routed with 1,425 tracks and 290 vias.
It is built around the LFE5U-85F-8BG381C, FT231XQ-R and IS25LP128-JKLE, with the IS66WVE4M16EBLL-70BLI, APTD1608LZGCK and APTD1608LSURCK among its other parts. Its parts include 39 capacitors, 38 resistors, 14 diodes, 7 ICs and 3 inductors. It belongs with the fPGA and programmable logic boards and the FPGA and CPLD boards of this library.
Main components
12LFE5U-85F-8BG381C
CABGA-3810℃~+85℃ 1.045V~1.155V 205 21000 3833856bit 84000 ECP5 Supports hot swap、Supports SEU error detection and correction CABGA-381 Programmable Logic Device (CPLDs/FPGAs) ROHSLatticeProgrammable Logic Device (CPLDs/FPGAs)FT231XQ-R
QFN-20-EP(4x4)-40℃~+85℃ 125uA 3.3V~5V 8mA USB 2.0 USB to UART QFN-20-EP(4x4) USB Converters ROHSFTDIUSB ConvertersIS25LP128-JKLE
WSON-8-EP(5x6)-40℃~+105℃ 100,000 cycles 10uA 128Mbit 133MHz 2.3V~3.6V 20 Years 800us Hardware write protection、Software write protection、Write enable latch SPI WSON-8-EP(5x6) NOR FLASH ROHSISSINOR FLASHIS66WVE4M16EBLL-70BLI
TFBGA-48(6x8)-40℃~+85℃ 2.7V~3.6V 200uA 64Mbit 70ns Built-in auto-refresh logic、Partial array refresh、Temperature compensated refresh、Built-in voltage sensor TFBGA-48(6x8) PSRAM ROHSISSISRAMAPTD1608LZGCK
0603-40℃~+85℃ 102.5mW 2.65V 2mA 420mcd 515nm 525nm 60° Discrete Diode Emerald Green Water Clear 0603 LED Indication - Discrete ROHSKingbrightLED Indication - DiscreteAPTD1608LSURCK
0603-40℃~+85℃ 110mcd 2.1V 2mA 60° 630nm 645nm 75mW Discrete Diode Red Water Clear 0603 LED Indication - Discrete ROHSKingbrightLED Indication - DiscreteCL10C101FB81PNC
0603100pF 50V C0G ±1% 0603 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSSamsung Electro-MechanicsMultilayer Ceramic Capacitors MLCC - SMD/SMTDFE322512F-2R2M=P2
12102.2uH 2.6A 3.4A 66mΩ ±20% 1210 Power Inductors ROHSMurataPower InductorsAPTD1608LVBC/D
SMD,1.6x0.8mm-40℃~+85℃ 120mW 2.65V 2mA 40° 465nm 470nm 65mcd Blue Discrete Diode Water Clear SMD,1.6x0.8mm LED Indication - Discrete ROHSKingbrightLED Indication - DiscreteAPTD1608LSYCK/J3-PF
SMD,1.6x0.8mm-40℃~+85℃ 1.85V 2mA 55mcd 590nm 590nm 60° 75mW Discrete Diode Water Clear Yellow SMD,1.6x0.8mm LED Indication - Discrete ROHSKingbrightLED Indication - DiscreteECS-7050MV-500-DM-TR
SMD7050-4PSMD7050-4P Crystal Oscillators ROHSECSCrystal OscillatorsFTS-120-02-L-DV
SMD,P=1.27mmPin HeadersSamtec
README
README.mdBlue Whale Hardware
ECP5 FPGA board for developing a RISCV processor.
Software
The ECP5 FPGA board was developed to enable the development of a RISCV processor and allow for for an extension connector. See the RISCV_PROCESSOR project for detailed explanation of the Verilog code developed for this board.
Project Status
The HW has been fully verified as part of the RISCV_PROCESSOR project. An extension board was developed to test the extension interface.

How To setup KiCAD
Checkout the KiCAD project and open it. In the Configure Paths dialog add: Name: ECP5_BGA381_RISCV and Path: "The full path to the GitHub directory"/GitHub/ECP5_BGA381_RISCV
In the Manage Symbol Libraries click the Project Specific Libraries tab and add: Name: ECP5_BGA381_RISCV and Library Path: ${ECP5_BGA381_RISCV}/symbols/Symbols.kicad_sym
In the Manage Footprint Libraries click the Project Specific Libraries tab and add: Name: ECP5_BGA381_RISCV and Library Path: ${ECP5_BGA381_RISCV}/footprints/Footprints.pretty
Parts
115| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C3, C4, C6, C7, C11, C12, C13, C14, C15, C22, C23, C24, C25, C37, C38 +1 |
| 9 | 22µF | Capacitor_SMD:C_0603_1608Metric | C17, C18, C20, C28, C29, C31, C33, C34, C36 |
| 7 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R2, R6, R7, R8, R13, R19 |
| 7 | 2.2µF | Capacitor_SMD:C_0603_1608Metric | C10, C19, C21, C26, C30, C35, C39 |
| 6 | 330 | Resistor_SMD:R_0603_1608Metric | R16, R24, R26, R28, R30, R32 |
| 4 | 4.7K | Resistor_SMD:R_0603_1608Metric | R3, R9, R10, R36 |
| 4 | 715 | Resistor_SMD:R_0603_1608Metric | R11, R12, R25, R29 |
| 4 | GREEN | LED_SMD:LED_0603_1608Metric | D1, D3, D10, D14 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 4 | RED | LED_SMD:LED_0603_1608Metric | D2, D5, D7, D11 |
| 3 | 100pF | Capacitor_SMD:C_0603_1608Metric | C16, C27, C32 |
| 3 | 15K | Resistor_SMD:R_0603_1608Metric | R33, R35, R37 |
| 3 | 2.2µH | Inductor_SMD:L_1210_3225Metric | L1, L2, L3 |
| 3 | 750 | Resistor_SMD:R_0603_1608Metric | R17, R27, R31 |
| 3 | BLUE | LED_SMD:LED_0603_1608Metric | D6, D8, D12 |
| 3 | TLV62569DBVT | Package_TO_SOT_SMD:SOT-23-5 | U5, U6, U7 |
| 3 | YLW | LED_SMD:LED_0603_1608Metric | D4, D9, D13 |
| 2 | 1.1K | Resistor_SMD:R_0603_1608Metric | R4, R5 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C5, C9 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric | R14, R15 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R22, R23 |
| 2 | GND | TestPoint:TestPoint_THTPad_D2.0mm_Drill1.0mm | TP1, TP2 |
| 1 | 1.6K | Resistor_SMD:R_0603_1608Metric | R18 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric | R21 |
| 1 | 130 | Resistor_SMD:R_0603_1608Metric | R20 |
| 1 | 18K | Resistor_SMD:R_0603_1608Metric | R34 |
| 1 | 3.3K | Resistor_SMD:R_0603_1608Metric | R38 |
| 1 | 4.7µF | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 50MHz | ECP5_BGA381_RISCV:Oscillator_SMD_Diodes_FN-4Pin_7.0x5.0mm | Y1 |
| 1 | 600Ohm 2A | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | EXT | ECP5_BGA381_RISCV:FTS-120-02-L-DV | J2 |
| 1 | FT231XQ | Package_DFN_QFN:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U3 |
| 1 | Hold 750mA | ECP5_BGA381_RISCV:Fuse_1812_4532Metric | F1 |
| 1 | IS25LP128F | ECP5_BGA381_RISCV:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U2 |
| 1 | IS66WVE4M16EBLL-70BLI | ECP5_BGA381_RISCV:BGA48C75P8X6_800X600X120N | U4 |
| 1 | LFE5U-85F-8BG381C | ECP5_BGA381_RISCV:BGA-381_pitch0.8mm_dia0.4mm | U1 |
| 1 | LOGO | LOGO | G*** |
| 1 | MMST2222A | Package_TO_SOT_SMD:SOT-323_SC-70 | Q1 |
| 1 | USB Type C | ECP5_BGA381_RISCV:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | User | Button_Switch_SMD:SW_SPST_PTS645 | SW1 |
Similar boards
- 4 layers64.4 × 54.6 mm

- 4 layers54.6 × 54.6 mm

- 4 layers166.6 × 94 mm

Panel
nrdsp/rvPhone
The goal of the this project is to develop a privacy enhanced, simple and fully featured mobile phone.
319 parts - 4 layers70 × 54.5 mm

Int debugger
TUDSSL/DIPS
This is the official public repository for DIPS: Debugger for Intermittently-Powered Systems. The repository consists of all components that make DIPS: - Hardware - Debugger Firmware - Emulator Firmware - Emulator Host…
224 parts - 6 layers100.2 × 63.5 mm

- 4 layers38 × 49 mm

NDS TV OUT V1I2
LNH-team/Lost-NDS-TV
The Lost Nintendo DS Television Output, brought back to life
48 parts488GPL-3.0 - 2 layers36.8 × 20.1 mm

Parallel port headphone dac
roybaer/parallel_port_headphone_dac
This is a reasonably accurate replica of the early 1990s SoundJr device by SiliconSoft.
37 parts4 - 2 layers115 × 70.6 mm

Questions
How big is the ECP5 PCB?
It measures 54.6 × 54.6 mm and has 4 copper layers, 1.58 mm thick.
What parts does the ECP5 use?
115 parts, built around the LFE5U-85F-8BG381C, FT231XQ-R, IS25LP128-JKLE and IS66WVE4M16EBLL-70BLI. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ECP5 KiCad files?
From the gildobjanschi/ECP5_BGA381_RISCV repository on GitHub, at the commit this page was made from: the board is ECP5.kicad_pcb and its schematic ECP5.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ECP5 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
