
GNSS Firehose
pmonta/GNSS_Firehose
Wideband front-end digitizer for GPS, GLONASS, Galileo, BeiDou

1G Ethernet FPGA HAT for Raspberry PI
Figa pi is an open-source printed circuit board by genrnd, from the genrnd/figa-pi.hw repository on GitHub. It is a 4-layer board of 65 × 56 mm with 159 parts on 147 nets, routed with 1,705 tracks and 267 vias.
It is built around the KSZ9021GN, CDCLVC1102PW and 24LC32A/SN, with the ASEMB-25.000MHZ-LC-T, NUP4114UPXV6T1G-N and LQH3NPN1R0MJRL among its other parts. Its parts include 65 capacitors, 43 resistors, 16 inductors, 9 ICs and 9 connectors. It belongs with the fPGA and programmable logic and interfaces and adapters boards of this library.
figa-pi -- expansion board (HAT, hardware attached top) for Raspberry PI with FPGA and 1G ethernet port.
Open hardware poject, made with Kicad.
General RnD LLC, 2018, http://genrnd.com
| Qty | Value | Footprint | References |
|---|---|---|---|
| 41 | 0.1uF | Capacitors_SMD:C_0603 | C1, C2, C3, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C25 +25 |
| 14 | 10uF | Capacitors_SMD:C_0603 | C6, C22, C23, C24, C26, C27, C28, C29, C33, C34, C37, C40, C62, C64 |
| 10 | 10k | Resistors_SMD:R_0603 | R7, R9, R14, R15, R16, R17, R23, R25, R26, R27 |
| 10 | BLM18PG330SN1D | Inductors_SMD:L_0603 | L1, L2, L3, L4, L5, L6, L13, L14, L15, L16 |
| 7 | 0.01uF | Capacitors_SMD:C_0603 | C49, C50, C52, C53, C55, C57, C59 |
| 7 | 1k | Resistors_SMD:R_0603 | R8, R10, R13, R18, R19, R20, R42 |
| 6 | 33R | Resistors_SMD:R_0603 | R4, R36, R37, R38, R39, R40 |
| 6 | 390R | Resistors_SMD:R_0603 | R1, R2, R3, R5, R6, R43 |
| 6 | Fiducial_1mm_Dia_2.54mm_Outer_CopperTop | Fiducials:Fiducial_1mm_Dia_2.54mm_Outer_CopperTop | REF1, REF2, REF3, REF3, REF4, REF5 |
| 4 | 3mm_Mounting_Hole | project_footprints:NPTH_3mm_ID | H1, H2, H3, H4 |
| 3 | 22uF | Capacitors_SMD:C_0603 | C30, C31, C32 |
| 3 | 28k 1% | Resistors_SMD:R_0603 | R31, R33, R35 |
| 3 | 4.99k 1% | Resistors_SMD:R_0603 | R21, R22, R24 |
| 3 | BLM21PG300SN1D | Inductors_SMD:L_0805 | L10, L11, L12 |
| 3 | LQH3NPN1R0MJRL | project_footprints:LQH3NPN | L7, L8, L9 |
| 3 | PLS-1 | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | J7, J8, J9 |
| 3 | TLV62084DSGR | library:WSON-8_1EP_2x2mm_Pitch0.5mm | U9, U10, U11 |
| 2 | 220R | Resistors_SMD:R_0603 | R28, R29 |
| 2 | 3.92k | Resistors_SMD:R_0603 | R11, R12 |
| 2 | 7914J-1-000E | project_footprints:7914J-1-000E | SW1, SW2 |
| 1 | 10CL025ZE144 | library:EQFP-144_20x20mm_Pitch0.5mm | U5 |
| 1 | 127k 1% | Resistors_SMD:R_0603 | R30 |
| 1 | 178k 1% | Resistors_SMD:R_0603 | R32 |
| 1 | 24LC32A/SN | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U1 |
| 1 | 46.4k 1% | Resistors_SMD:R_0603 | R34 |
| 1 | AM23ESGC | project_footprints:AM23ESGC | VD2 |
| 1 | ASEMB-25.000MHZ-LC-T | Oscillators:Oscillator_SMD_Abracon_ASE-4pin_3.2x2.5mm | U2 |
| 1 | BH-10(IDC-10MS) | Connectors_IDC:IDC-Header_2x05_Pitch2.54mm_Straight | J1 |
| 1 | CDCLVC1102PW | Housings_SSOP:TSSOP-8_4.4x3mm_Pitch0.65mm | U7 |
| 1 | DNI_4.99k 1% | Resistors_SMD:R_0603 | R41 |
| 1 | DNI_PLS-2 | Pin_Headers:Pin_Header_Straight_1x02_Pitch2.54mm | J2 |
| 1 | DNI_POE | Socket_Strips:Socket_Strip_Straight_2x02_Pitch2.54mm | J6 |
| 1 | KAA-3528EMBSGCT | project_footprints:LED_RGB_3528 | VD8 |
| 1 | KP-1608SGC | LEDs:LED_0603 | VD6 |
| 1 | KP-1608SRC | LEDs:LED_0603 | VD1 |
| 1 | KSZ9021GN | library:QFN-64-1EP_8x8mm_Pitch0.4mm | U6 |
| 1 | L829-1J1T-43 | library:L829 | J5 |
| 1 | LOGO | project_footprints:Logo | G*** |
| 1 | NUP4114UPXV6T1G | library:SOT-563-6 | U3 |
| 1 | PBD-40(DS1023-2x20) | Socket_Strips:Socket_Strip_Straight_2x20_Pitch2.54mm | J3 |
| 1 | TestPoint_5000-5004 | Connectors_TestPoints:Test_Point_Keystone_5000-5004_Miniature | J10 |

pmonta/GNSS_Firehose
Wideband front-end digitizer for GPS, GLONASS, Galileo, BeiDou


daverowntree/SmartDesk
I open sourced a design I made a few years back for a non-paying client. Use it as you see fit!


gumulka/ble_door_sensor
A simple project to observe a window or door is open/closed. It works like most other sensors as well. A magnet has to get attached to the door and if it comes near the board, it is detected and the state of the window…


Prajwal-sahyadri-ECE/-Optimized-Powersupply-design-
A highly detailed PCB to maintain an power supply for a defined hardware architecture specifically for ICS system

It measures 65 × 56 mm and has 4 copper layers, 1.6 mm thick.
159 parts, built around the KSZ9021GN, CDCLVC1102PW, 24LC32A/SN and ASEMB-25.000MHZ-LC-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the genrnd/figa-pi.hw repository on GitHub, at the commit this page was made from: the board is kicad/figa-pi.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask genrnd before reusing the design.