

STM32
Design files of our hall effect sensor analog keypads
- Size
- 9.3 × 66.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 71
- Nets
- 77
- Pads
- 263
- Tracks, vias
- 996, 380
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 19 Feb 2023
- Updated
- 7 May 2025
Overview
STM32 is an open-source printed circuit board by gamaPhy, from the gamaPhy/Freedom repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 4-layer board of 9.3 × 66.8 mm with 71 parts on 77 nets, routed with 996 tracks and 380 vias.
It is built around the SLSS49E-3, ME6208A44M3G and ME6212C25M5G, with the PRTR5V0U2X, WS2812B and TS-1187A-B-A-B among its other parts. Its parts include 30 capacitors, 10 diodes, 7 resistors, 7 ICs and 5 switches. It belongs with the STM32 boards of this library.
Main components
10SLSS49E-3
SOT-23-40℃~+150℃ 1.5mA 3V~12V 5mA Built-in Schmitt trigger Omnipolar SOT-23 Linear Hall Sensors ROHSSlkorHall SwitchesME6208A44M3G
SOT-23-45℃~+150℃ 1 150mA 18V 1V@(200mA) 3uA 4.4V Fixed Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsME6212C25M5G
SOT-23-5-40℃~+85℃@(Ta) 1 2.5V 220mV@(200mA) 300mA 50uA 50uVrms 57dB@(10kHz) 6V Enable Fixed Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedTS-1187A-B-A-B
SMD-4P,5.1x5.1mm-30℃~+85℃ 1.5mm 1.6N 100,000 cycles 12V 5.1mm 5.1mm 50mA Gold No Round Button SPST Surface Mount,Vertical Without Bracket SMD-4P,5.1x5.1mm Tactile Switches ROHSXKB ConnectionTactile SwitchesBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsGZ2012D601TF
0805-55℃~+125℃ 1 300mΩ 500mA 600Ω@100MHz ±25% 0805 Ferrite Beads ROHSSunlordFerrite BeadsUSB-TYPE-C-016
SMD-25℃~+85℃ 1 16P 3A 5,000 cycles 5V 6.5mm Female Laminated board Type-C SMD USB Connectors ROHSDEALONUSB ConnectorsNSMD050-24V
12061.4mm 1.8mm 100A 100ms 150mΩ 1A 24V 3.5mm 500mA 600mW 700mΩ 1206 Resettable Fuses ROHS台湾陆海Resettable Fuses
README
README.mdFreedom series Analog Keypads
Tech Stack
KFC (Kicad, Freecad, C)
Firmware
https://github.com/gamaPhy/qmk-keyboards/tree/main/firmware/freedom
Images
How To
Create an PCB outline in FreeCAD and import to Kicad
- Create sketch in FreeCAD
- Mirror sketch
- Merge original sketch and mirrored sketch together
- Export the merged sketch as
filename.dxf(An Autodesk DXF 2D file) - In Kicad, import graphics as an
Edge.Cutslayer
Parts
71| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C3, C11, C15, C16, C17, C21, C22, C23, C24, C25, C26, C27, C28, C29, C30 +3 |
| 10 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10 |
| 4 | 10k | Resistor_SMD:R_0402_1005Metric | R4, R5, R6, R7 |
| 4 | 10u | Capacitor_SMD:C_1206_3216Metric | C7, C8, C9, C10 |
| 3 | SLSS49E | Package_TO_SOT_SMD:SOT-23 | U4, U5, U6 |
| 2 | 1u | Capacitor_SMD:C_0402_1005Metric | C12, C13 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric | C18, C19 |
| 2 | 5.1k | Capacitor_SMD:C_0402_1005Metric | R1, R2 |
| 2 | MountingHole_6.4mm_M6_DIN965 | MountingHole:MountingHole_6.4mm_M6_DIN965 | H1, H2 |
| 2 | TS-1187A-B-A-B | Button_Switch_SMD:TS-1187A | SW1, SW2 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C14 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 47 | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 4u7 | Capacitor_SMD:C_0805_2012Metric | C20 |
| 1 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | BUTT1 | Button_Switch_SMD:PTS647_4.5x4.5mm | SW3 |
| 1 | BUTT2 | Button_Switch_SMD:PTS647_4.5x4.5mm | SW5 |
| 1 | BUTT3 | Button_Switch_SMD:PTS647_4.5x4.5mm | SW4 |
| 1 | Conn_01x04_Socket | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | GZ2012D601TF | Capacitor_SMD:C_0805_2012Metric | FB1 |
| 1 | ME6208A44M3G | Package_TO_SOT_SMD:SOT-23 | U1 |
| 1 | ME6212C25M5G | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | MountingHole_4.3mm_M4_DIN965 | MountingHole:MountingHole_4.3mm_M4_DIN965 | H3 |
| 1 | PRTR5V0U2X | Keebio-Parts:SOT-143B | U3 |
| 1 | STM32F401RCTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U7 |
| 1 | USB-TYPE-C-016 | Connector_USB:USB-TYPE-C-016_Receptacle_DEALON_16P_MidMnt | P1 |
| 1 | nSMD050-24V | Fuse:Fuse_1206_3216Metric | F1 |
The 68 most common of 71 parts.
More from gamaPhy/Freedom
2- 4 layers64.2 × 66.2 mm

- 2 layers62.1 × 65.9 mm

RP2040 minimal
gamaPhy/Freedom
Design files of our hall effect sensor analog keypads
40 parts3CERN-OHL-S-2.0
Similar boards
- 2 layers353.1 × 124.9 mm

- 2 layers70 × 100 mm

- 6 layers150 × 100 mm

- 2 layers242.9 × 95.3 mm

- 4 layers44.5 × 40.6 mm

- 4 layers315 × 147.2 mm

- 2 layers339.1 × 143.2 mm

- 2 layers475 × 139.9 mm

Skogaslider main pcb
skogaby/skogaslider
Firmware, CAD, and PCB files for the skogaslider, an RP2040-based controller to simulate Chunithm's gameplay experience
175 parts18MIT
Questions
How big is the STM32 PCB?
It measures 9.3 × 66.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the STM32 use?
71 parts, built around the SLSS49E-3, ME6208A44M3G, ME6212C25M5G and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STM32 KiCad files?
From the gamaPhy/Freedom repository on GitHub, at the commit this page was made from: the board is Electrical/keypad/3k/stm32/STM32.kicad_pcb and its schematic Electrical/future_development/proto_oled/RP2040_minimal.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the STM32 design in my own project?
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).