
MCU PROTO 100x68mm
galopago/misistemote
Misistemote is an Open Source, modular ecosystem that uses pre-made PCB to mix and match your choice of processor board.

Misistemote is an Open Source, modular ecosystem that uses pre-made PCB to mix and match your choice of processor board. Is oriented to make small, mobile, battery powered electronic projects work in real conditions in a very short time.
Mcu proto-115x70mm is an open-source printed circuit board by galopago, from the galopago/misistemote repository on GitHub, published under the MIT licence. It is a 2-layer board of 115 × 70 mm with 2,786 parts on 2 nets, routed with 1,673 tracks and 0 vias.
It belongs with the ESP32 and RISC-V boards of this library.
The board is designed to fit inside a generic 83x58mm waterproof enclosure.

Read this in other languages: Español , Portugues
The PCB was developed in KiCad V5.1,
The module could be placed vertically to maximize square shaped free area, for additional modules, LiPo batteries, etc.

The board also could be placed horizontally to make room for a cylindrical battery cell.

Image sensor sees through the transparent enclosure

Female headers used to raise the image sensor as close to the case as possible. There is now some free space for additional electronics.

Panelized PCB version


galopago/misistemote
Misistemote is an Open Source, modular ecosystem that uses pre-made PCB to mix and match your choice of processor board.

galopago/misistemote
Misistemote is an Open Source, modular ecosystem that uses pre-made PCB to mix and match your choice of processor board.

galopago/misistemote
Misistemote is an Open Source, modular ecosystem that uses pre-made PCB to mix and match your choice of processor board.

galopago/misistemote
Misistemote is an Open Source, modular ecosystem that uses pre-made PCB to mix and match your choice of processor board.

SolderedElectronics/IO-expander-MCP23017-breakout-hardware-design
Hardware design, BOM, gerbers and 3D files for IO-expander-MCP23017-breakout designed by Soldered Electronics.

Tessavana/Soft-interfaces-files
Sharing all circuit, PCB, code and design files to be able to replicate EOP soft interfaces

FrankBuss/mesh
This project implements a 30x30 node resistor mesh for testing it approximately. The mesh contains 1,740 resistors (870 horizontal + 870 vertical connections), each a 1kΩ 0805 SMD resistor with 0.1% precision.


SolderedElectronics/I2C-multiplexer-TCA9548A-breakout-hardware-design
Hardware design, BOM, gerbers and 3D files for I2C-multiplexer-TCA9548A-breakout designed by Soldered Electronics.


embeddedos-org/eCAD-Hardware-Products
Hardware designs + EE docs + Board datasheets of Multiple products

idlehandsdev/black_rabbit
A low poly LED mask made completely out of circuit boards. Second version of a series of high tech face changing masks.
It measures 115 × 70 mm and has 2 copper layers, 1.6 mm thick.
2,786 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the galopago/misistemote repository on GitHub, at the commit this page was made from: the board is mcu-proto-115x70mm/mcu-proto-115x70mm.kicad_pcb and its schematic mcu-proto-100x68mm/MCU_PROTO_100x68mm.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).