

Voyager65
Fully versatile 65% keyboard PCB. Simplified variants available.
- Size
- 303.2 × 94.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 224
- Nets
- 164
- Pads
- 1,323
- Tracks, vias
- 3,473, 184
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 20 Aug 2018
- Updated
- 27 Jun 2018
Overview
Voyager65 is an open-source printed circuit board by foggyflute, from the foggyflute/Voyager65 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 303.2 × 94.5 mm with 224 parts on 164 nets, routed with 3,473 tracks and 184 vias.
It is built around the ATXMEGA32A4U-MH, 74LVC1G34Z and IS31FL3733-QFLS4-TR, with the MCP1700T-3002E/TT(MS), PRTR5V0U2X and WS2812B among its other parts. Its parts include 83 diodes, 26 capacitors, 8 resistors, 5 ICs and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATXMEGA32A4U-MH
VQFN-44-EP(7x7)-40℃~+85℃ 1.6V~3.6V 12bit 12bit 1KB 32KB 32MHz 34 4KB 8/16 Bit AVR Built-in FLASH VQFN-44-EP(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)74LVC1G34Z
SOT-553-5-40℃~+125℃ 1 1 1.65V~5.5V 1.6ns@5V,50pF 10uA 32mA 32mA 74LVC Power-off isolation Push-pull Unidirectional SOT-553-5 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, TransceiversIS31FL3733-QFLS4-TR
VQFN-48-EP(6x6)-40℃~+125℃ 1MHz 2.7V~5.5V 28 46mA Built-in PWM Short Circuit Protection、LED open-circuit protection QFN-48-EP(6x6) LED Drivers ROHSISSILED DriversMCP1700T-3002E/TT(MS)
SOT-23-40℃~+125℃@(Tj) 1 120uVrms 180mV@(300mA) 2uA 300mA 3V 5.5V 80dB@(100Hz) Fixed Over Current Protection、Over Temperature Protection Positive SOT-23 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorisedTC2030-IDC-NL
UncategorisedTag Connect
README
Plate/Tada68-Alps/README.md#WARNING
Alps switches are wide! This means a regular M2 screw WILL NOT FIT between two keys, i.e. between G and H!
To get around this, find M2 screws with head diameters smaller than 3.45mm.
Also, the screwdriver for securing the screw must be less than 1.7mm diameter.
Parts
224| Qty | Value | Footprint | References |
|---|---|---|---|
| 71 | D_Small | Diodes_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +55 |
| 57 | MX-1U | MX_Alps_Hybrid:MX-1U | K_-1, K_,1, K_;1, K_.1, K_'1, K_/1, K_#0_1, K_#1, K_#2, K_#3, K_#4, K_#5, K_#6, K_#7, K_#8, K_#9 +41 |
| 19 | 0.1u | Capacitors_SMD:C_0603 | C2, C3, C4, C5, C8, C9, C10, CRGB1, CRGB2, CRGB3, CRGB4, CRGB5, CRGB6, CRGB10, CRGB11, CRGB12 +3 |
| 12 | WS2812B | WS2812B:WS2812B | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9, LED10, LED11, LED12 |
| 6 | MX-1.5U | MX_Alps_Hybrid:MX-1.5U | K_\1, K_LM1, K_LM7, K_RM5, K_TAB1, SP8 |
| 4 | 0.47u | Capacitors_SMD:C_0603 | C11, C12, C13, C14 |
| 4 | MX-1.25U | MX_Alps_Hybrid:MX-1.25U-FLIPPED | K_CAPS2, K_LM2, K_LM4, SP4 |
| 3 | MX-1.25U | MX_Alps_Hybrid:MX-1.25U | K_LM5, K_LM6, K_RM3 |
| 2 | 1k | Resistors_SMD:R_0603 | R3, R4 |
| 2 | 5.1k | Resistors_SMD:R_0603 | R6, R7 |
| 2 | MX-1.5U | MX_Alps_Hybrid:MX-1.5U-FLIPPED | K_LM3, K_RM2 |
| 2 | MX-1.75U | MX_Alps_Hybrid:MX-1.75U | K_CAPS1, K_SHIFT2 |
| 2 | MX-1U | MX_Alps_Hybrid:MX-1U-FLIPPED | K_RM4, K_RM6 |
| 2 | MX-2.25U | MX_Alps_Hybrid:MX-2.25U | K_ENTER1, K_SHIFT1 |
| 2 | MX-2.25U | MX_Alps_Hybrid:MX-2.25U-ReversedStabilizers | SP1, SP7 |
| 2 | MX-2.75U | MX_Alps_Hybrid:MX-2.75U-ReversedStabilizers | SP5, SP9 |
| 1 | 100k | Resistors_SMD:R_0603 | R2 |
| 1 | 10k | Resistors_SMD:R_0603 | R1 |
| 1 | 10u | Capacitors_SMD:C_0603 | C6 |
| 1 | 1u | Capacitors_SMD:C_0603 | C1 |
| 1 | 20k | Resistors_SMD:R_0603 | R8 |
| 1 | 22u | Capacitors_SMD:C_0805 | C7 |
| 1 | 470 | Resistors_SMD:R_0603 | R5 |
| 1 | 500mA | Resistors_SMD:R_0805 | F1 |
| 1 | 74LVC1G34 | TO_SOT_Packages_SMD:SOT-353_SC-70-5 | U5 |
| 1 | ATXMEGA32A4U-MH | Housings_DFN_QFN:QFN-44-1EP_7x7mm_Pitch0.5mm | U1 |
| 1 | HRO-TYPE-C-31-M-12 | Type-C:HRO-TYPE-C-31-M-12 | USB1 |
| 1 | IS31FL3733-QFLS4-TR | Housings_DFN_QFN:QFN-48-1EP_6x6mm_Pitch0.4mm | U4 |
| 1 | LOGO | locallib:ai-7.6 | G*** |
| 1 | LOGO | locallib:icon-7.6 | G*** |
| 1 | MCP1700T-3002E/TT | TO_SOT_Packages_SMD:SOT-23 | U2 |
| 1 | MX-2U | MX_Alps_Hybrid:MX-2U | K_BACK1 |
| 1 | MX-6.25U | MX_Alps_Hybrid:MX-6.25U-ReversedStabilizers | SP3 |
| 1 | MX-6.5U | MX_Alps_Hybrid:MX-6.5U-FLIPPED-ReversedStabilizers | SP6 |
| 1 | MX-7U | MX_Alps_Hybrid:MX-7U-ReversedStabilizers | SP2 |
| 1 | PRTR5V0U2X | locallib:SOT143B | U3 |
| 1 | SW_PUSH | Molex-0548190589:SKQG-1155865 | SW1 |
| 1 | TC2030-IDC | Tag-Connect:TC2030-NL_SMALL_AND_IDC_PDI | P1 |
The 214 most common of 224 parts.
Similar boards
- 2 layers302.4 × 98.8 mm

- 2 layers109 × 71 mm

- 2 layers99.7 × 74.8 mm

- 2 layers285 × 94.6 mm

- 2 layers282.7 × 117.3 mm

- 4 layers171 × 124 mm

- 4 layers338.8 × 170.4 mm

- 2 layers395.3 × 138.1 mm

Custom keyboard (f303)
howardt12345/keyboard0
TKL + macro keys, 2 rotary encoders, and OLED
514 parts15
Questions
How big is the Voyager65 PCB?
It measures 303.2 × 94.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Voyager65 use?
224 parts, built around the ATXMEGA32A4U-MH, 74LVC1G34Z, IS31FL3733-QFLS4-TR and MCP1700T-3002E/TT(MS). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Voyager65 KiCad files?
From the foggyflute/Voyager65 repository on GitHub, at the commit this page was made from: the board is Voyager65.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Voyager65 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).