

Sacci
Sistema Automatizado de Corrosão de Circuito Impresso
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 165
- Nets
- 43
- Pads
- 543
- Tracks, vias
- 1,509, 30
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 8 Jun 2016
- Updated
- 8 Jun 2016
Overview
Sacci is an open-source printed circuit board by fmakara, from the fmakara/sacci repository on GitHub. It is a 2-layer board with 165 parts on 43 nets, routed with 1,509 tracks and 30 vias.
It is built around the ATMEGA328-PU, MOC3021M and BC328, with the BC338 among its other parts. Its parts include 30 capacitors, 30 resistors, 27 diodes, 27 connectors and 21 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
4ATMEGA328-PU
PDIP-28-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH PDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MOC3021M
DIP-6-40℃~+85℃ 0.1mA 1 1.15V 100mA 330mW 4.17kV 400V 6 60mA No TRIAC DIP-6 Triac, SCR Output Optoisolators ROHSonsemiTriac, SCR Output OptoisolatorsBC328
TO-921 PNP 100MHz 25V 5V 625mW 630 700mV 800mA PNP TO-92 Bipolar (BJT) ROHSDDFBipolar (BJT)BC338
TO-921 NPN 100MHz 25V 5V 625mW 630 700mV 800mA NPN TO-92 Bipolar (BJT) ROHSDDFBipolar (BJT)
README
README.mdsacci
Sistema Automatizado de Corrosão de Circuito Impresso
Feito com KiCAD versão 4.0.2 e Atmel Studio
Quase concluido, faltando apenas implementar o circuito de acionamento da resistencia e o seletor de cuba (para a cuba de água)
Parts
165| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 100n | C2 | C1, C1, C1, C2, C2, C2, C3, C3, C3, C4, C4, C4, C6, C10, C10, C10 +8 |
| 12 | 1n4001 | D3 | D2, D2, D2, D7, D7, D7, D8, D8, D8, D9, D9, D9 |
| 12 | 1n4148 | SIL-2 | D3, D3, D3, D4, D4, D4, D5, D5, D5, D6, D6, D6 |
| 12 | 330 | R3-LARGE_PADS | R7, R7, R7, R8, R8, R8, R9, R9, R9, R10, R10, R10 |
| 12 | SW_PUSH | SW_PUSH_SMALL | SW1, SW1, SW1, SW2, SW2, SW2, SW3, SW3, SW3, SW4, SW4, SW4 |
| 9 | 10k | R3-LARGE_PADS | R2, R2, R2, R4, R4, R4, R5, R5, R5 |
| 6 | 100u | C1V8 | C5, C5, C5, C8, C8, C8 |
| 6 | BC328 | TO92DGS | Q1, Q1, Q1, Q3, Q3, Q3 |
| 6 | BC338 | TO92DGS | Q2, Q2, Q2, Q4, Q4, Q4 |
| 6 | Term 1 | PIN_ARRAY_2X1 | P2, P2, P2, P3, P3, P3 |
| 3 | 10k pot | PINHEAD1-3 | RV1, RV1, RV1 |
| 3 | 16MHz | HC-49V | X1, X1, X1 |
| 3 | 220 | R3-LARGE_PADS | R3, R3, R3 |
| 3 | 470r | R3-LARGE_PADS | R6, R6, R6 |
| 3 | 500 | R3-LARGE_PADS | R1, R1, R1 |
| 3 | 7805 | LM78XXV | U2, U2, U2 |
| 3 | ATMEGA328-P | DIP-28__300_ELL | IC1, IC1, IC1 |
| 3 | AVR-ISP-10 | PIN_ARRAY_5x2 | CON1, CON1, CON1 |
| 3 | Alim 110 | PIN_ARRAY_2X1 | P6, P6, P6 |
| 3 | DISPLAY | LCD_ALPHA | S1, S1, S1 |
| 3 | LED_DISPLAY | PIN_ARRAY_2X1 | P1, P1, P1 |
| 3 | LED_RES | LED-3MM | D1, D1, D1 |
| 3 | MOC3021M | DIP-6__300_ELL | IC2, IC2, IC2 |
| 3 | Resistencia | PIN_ARRAY_2X1 | P7, P7, P7 |
| 3 | SW_BOT | PIN_ARRAY_3X1 | K2, K2, K2 |
| 3 | SW_TOP | PIN_ARRAY_3X1 | K1, K1, K1 |
| 3 | TIC206 | PINHEAD1-3 | U1, U1, U1 |
| 3 | Trafo 110 | PIN_ARRAY_2X1 | P5, P5, P5 |
| 3 | Trafo 9V | PIN_ARRAY_2X1 | P4, P4, P4 |
| 3 | motor 1 | PIN_ARRAY_2X1 | P8, P8, P8 |
More from fmakara/sacci
1- 2 layers

Similar boards
- 2 layers46.4 × 60.3 mm

- 2 layers35 × 33 mm

- 2 layers99.9 × 99.9 mm

Maquina compostaje
dani0421/Compostaje
El SDA se conecta al pin 33 del ESP32 y el SCL al pin 36 de ESP32, cabe resaltar que en la placa no quedaran orificios para la pantalla, unicamente los pines para hacer la conexión.
103 parts - 2 layers165 × 254 mm

GSE14
stonedDiscord/Automatenplatinen
Reverse engineerte Hardware aus deutschen Spielautomaten.
164 parts5BSD-2-Clause - 2 layers99.7 × 69.9 mm

- 2 layers

- 2 layers101.6 × 101.6 mm

ARDUINO PLC
Reiken3099/ArduPLC
PCB designs made with the purpose of using both Arduino hardware and software in an industrialized way adapting said hardware for said purpose. These designs are made in KICAD free software
92 parts1CC0-1.0 - 2 layers100 × 64.7 mm

Questions
What parts does the Sacci use?
165 parts, built around the ATMEGA328-PU, MOC3021M, BC328 and BC338. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sacci KiCad files?
From the fmakara/sacci repository on GitHub, at the commit this page was made from: the board is placa1/sacci.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sacci design in my own project?
Its repository states no licence, so its author keeps all rights: ask fmakara before reusing the design.