Skip to the content
2 layers119 × 92 mmBlink A, the printed circuit board in 3D

Blinking lights to tell time

Size
119 × 92 mm
Copper layers
2
Thickness
1.6 mm
Parts
164
Nets
180
Pads
596
Tracks, vias
2,362, 207
Pours
13
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
13 Mar 2023
Updated
15 Jun 2025

Overview

Blink A is an open-source printed circuit board by fluffy, from the fluffy/blinky repository on GitHub. It is a 2-layer board of 119 × 92 mm with 164 parts on 180 nets, routed with 2,362 tracks and 207 vias.

It is built around the CH340C, AD8397AR and TMP112AIDRLR(UMW), with the SN74LVC1G14DBV, AMS1117-3.3 and MAX40200AUK among its other parts. Its parts include 57 resistors, 39 capacitors, 15 ICs, 14 connectors and 4 switches. It belongs with the STM32 boards of this library.

Main components

12

README

README.md

blinky

Blinking lights to tell time. And it beeps.

Build and flash

Build with:

text
mkdir build ; cd build ; cmake .. ; make

Note when programming the GPS board, the GPS must be unplugged while programming.

Program flash using stlink with:

text
st-flash --reset --format ihex write build/blinky.hex

Can program using Stm32CubeProgrammer with RTS=1, DTR=0, baud at 115200, Parity Even, data bits 8, stop bits 1, flow control off.

Program flash using USB serial with:

text
stm32flash -w build/blinky.hex -v -b 115200 -m 8e1 -i "-dtr," /dev/cu.usbserial-31110

If this fails, try the following reset then try to flash again. This will not work on a brand new uninitialized board, the board needs to be programmed for the first time with st-flash.

Can reset the board with:

text
stty -f /dev/cu.usbserial-31110 hup

Monitor output connect with Serial program. Use 115200 baud with 8 bits, no parity, 1 stop bit. Set the RTS and DTR both low. Screen fails to do this. It sets RTS and DTR both high it will not work.

To use python miniterm (replace usbserial-31110 with number on your machine):

text
pyserial-miniterm -e --parity N --rts 0 --dtr 0 /dev/cu.usbserial-31110 115200

Can exit the miniterm with CTRL+]. This will cause board reset when it starts.

Tools and Dependencies

Set up a mac to be able to build by installing:

  • TODO
  • pip3 install pyserial

Features

Blink Timing Board

On the Rev A hardware 1.0 software have:

  • Timing board with TXCO, LTC Sync in, LTC Sync out, LED grid, battery power, USB debug, audio in/out

  • Display 120 fps tick on 10x4 grid

  • 3.3V LTC Sync Out

  • PPS out is hold sync button while booting

  • Jitter of less than 1 ms

  • Jam sync to 3.3V Sync input

  • Time drift of < 5 ms in 1 hour

  • USB port for serial data

  • read calibration from EEPROM

  • audio out of beep

  • headset monitor of audio out

  • usb upgrade of firmware

  • Status LEDs: error(red), external synced (green), not sync ( blue ), have sync (teal)

  • audio input to detect beep

  • battery with 2h life and USB charger

Clock and GPS Board

On the Rev A hardware 0.2 software have:

  • GPS board with GPS, OCXO
  • LTC sync out, LTC sync in
  • Does not have audio or led display grid
  • 10 MHz sine wave output 1V p2p into 50 ohm, 3 channels
  • Sync to GPS PPS
  • Show current PPS offset from GPS PPS
  • Compare PPS accuracy to GPS over 24 hours
  • read calibration from EEPROM
  • USB serial display of: Time, GPS Error, SyncIn Error
  • Aux input of 10 MHz signal to compare
  • PPS jitter of about +/- 20 ns and error less than 10 ns
  • USB upgrade of firmware
  • USB 3A power for gps board
  • USB output serial data for computer time sync

Light GPS Board

On the Rev A hardware 0.2 software have:

  • GPS board with GPS
  • LTC sync out
  • Does not have audio or led display grid
  • Sync to GPS PPS
  • USB upgrade of firmware
  • USB power
  • USB output serial data for computer time sync

Wishlist

  • time into browser measure computer time offset
  • software upgrade from browser

Parts

164
QtyValueFootprintReferences
211K0Resistor_SMD:R_0603_1608MetricR10, R11, R17, R20, R23, R25, R27, R28, R29, R35, R36, R42, R43, R44, R45, R49 +5
13100nCapacitor_SMD:C_0402_1005MetricC1, C2, C12, C15, C18, C20, C21, C22, C23, C24, C30, C31, C32
10~TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP5, TP9, TP10, TP11, TP14, TP15, TP16, TP17, TP18, TP20
910uCapacitor_SMD:C_0603_1608MetricC3, C5, C7, C8, C13, C26, C33, C34, C35
847KResistor_SMD:R_0603_1608MetricR3, R4, R9, R39, R51, R52, R53, R59
7100nCapacitor_SMD:C_0603_1608MetricC4, C6, C9, C10, C17, C27, C36
64K7Resistor_SMD:R_0603_1608MetricR26, R31, R32, R33, R40, R41
6~TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mmTP1, TP2, TP3, TP4, TP12, TP13
5560RResistor_SMD:R_0603_1608MetricR1, R2, R13, R16, R19
4KH-BNC50-3511blinky_footprints:BNC_Amphenol_B6252HB-NPP3G-50_Horizontal-CJJ4, J11, J12, J13
4M2MountingHole:MountingHole_2.2mm_M2H1, H3, H4, H5
4SolderJumper_2_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mmJP1, JP2, JP3, JP4
30R1Resistor_SMD:R_1206_3216MetricR37, R38, R62
322uFCapacitor_SMD:C_0805_2012MetricC38, C39, C40
32N7002Package_TO_SOT_SMD:SOT-23Q3, Q4, Q5
3SN74LVC1G14DBVPackage_TO_SOT_SMD:SOT-23-5U5, U6, U14
3SW_Push_4PDTblinky_footprints:PBH4UOANAGXSW2, SW3, SW4
21K5Resistor_SMD:R_0603_1608MetricR12, R15
22u2Capacitor_SMD:C_0603_1608MetricC16, C19
233pCapacitor_SMD:C_0603_1608MetricC11, C14
247RResistor_SMD:R_0603_1608MetricR47, R48
24u7Capacitor_SMD:C_0603_1608MetricC28, C29
25K1Resistor_SMD:R_0603_1608MetricR21, R22
2AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U1, U13
2Conn_01x01Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_VerticalJ15, J16
2Conn_01x06_PinConnector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalJ5, J7
2MAX40200AUKPackage_TO_SOT_SMD:SOT-23-5U11, U12
2PJ-320Dblinky_footprints:Jack_3.5mm_PJ320D_Horizontal-CJJ2, J3
2SolderJumper_2_BridgedJumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mmJP5, JP6
11.5uHInductor_SMD:L_Coilcraft_XAL4020-XXXL1
1100KResistor_SMD:R_0603_1608MetricR8
110KResistor_SMD:R_0603_1608MetricR6
1150RResistor_SMD:R_0603_1608MetricR46
116MHz Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
11R0Resistor_SMD:R_0603_1608MetricR7
1200RResistor_SMD:R_0603_1608MetricR24
12K0Resistor_SMD:R_0603_1608MetricR30
133R0Resistor_SMD:R_0603_1608MetricR60
147pCapacitor_SMD:C_0603_1608MetricC25
15.6KResistor_SMD:R_0603_1608MetricR58
1AD8397Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU2
1CH340CPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU7
1Conn_01x02Connector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_HorizontalJ1
1Conn_01x03Connector_JST:JST_PH_S3B-PH-SM4-TB_1x03-1MP_P2.00mm_HorizontalJ6
1Conn_02x16_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x16_P2.54mm_VerticalJ14
1GTXO-14V (2.048MHz)blinky_footprints:OSC_DIP-14X1
1LEDLED_SMD:LED_0805_2012MetricD1
1LED_ABGRblinky_footprints:LED_RGB_MHS110FRGBCTD4
1M24C02-RMNPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU3
1MCP73832-2-OTPackage_TO_SOT_SMD:SOT-23-5U9
1STM32F405RGTxPackage_QFP:LQFP-64_10x10mm_P0.5mmU4
1SW_SPDTButton_Switch_THT:SW_E-Switch_EG1224_SPDT_AngledSW1
1TMP112AIDRLRPackage_TO_SOT_SMD:SOT-563U10
1TPS63060Package_SON:Texas_S-PWSON-N10_ThermalViasU16
1USBLC6-2P6Package_TO_SOT_SMD:SOT-666U8
1USB_C_Receptacleblinky_footprints:USB_C_Receptacle_HRO_TYPE-C-31-M-12J9
1~blinky_footprints:BatteryFlat1B1

More from fluffy/blinky

3
  • 2 layers119 × 92 mmClock A, the printed circuit board in 3D

    Clock A

    fluffy/blinky

    Blinking lights to tell time

    225 parts
  • 2 layers82 × 52 mmDisp A, the printed circuit board in 3D

    Disp A

    fluffy/blinky

    Blinking lights to tell time

    115 parts
  • 2 layers119 × 92 mmGps A, the printed circuit board in 3D

    Gps A

    fluffy/blinky

    Blinking lights to tell time

    90 parts

Similar boards

  • 2 layers475 × 139.9 mmSkogaslider main pcb, the printed circuit board in 3D

    Skogaslider main pcb

    skogaby/skogaslider

    Firmware, CAD, and PCB files for the skogaslider, an RP2040-based controller to simulate Chunithm's gameplay experience

    175 parts18MIT
  • 2 layers83.8 × 91.4 mmTangnano20k vectrex, the printed circuit board in 3D

    Tangnano20k vectrex

    ryomuk/tangnano20k-vectrex

    Tang Nano 20K top level module for Dar's Vectrex

    109 parts11
  • 4 layers100 × 80 mmBuilt, the printed circuit board in 3D

    Built

    devbisme/ai-circuit-design-tests

    Tests of KiCad-related AI tools.

    243 parts10
  • 2 layers78 × 61 mmMicromouse, the printed circuit board in 3D

    Micromouse

    F-Sakashita/Micromouse

    85 parts1
  • 2 layers200 × 100 mmPCB Transmission Line, the printed circuit board in 3D

    PCB Transmission Line

    marqueztronics/PCB-Transmission-Line

    A simple board with a 50-ohm transmission line for observing waves and reflections under the oscilloscope.

    7 parts1CERN-OHL-P-2.0
  • 2 layers51.5 × 41.5 mmDac module, the printed circuit board in 3D

    Dac module

    visgence/dac_module

    33 parts1
  • 4 layers114.3 × 108 mmPellet, the printed circuit board in 3D

    Pellet

    Mouse-GYM/auto-trainer-hardware

    Repository for hardware, firmware, and software related to the Mouse-GYM modules

    202 parts
  • 2 layers90.5 × 104.4 mmRP spectroscopy, the printed circuit board in 3D

    RP spectroscopy

    SimoneDamian/RP_Spectroscopy_kicad

    Circuits for the hardware part of the project

    96 parts

Questions

How big is the Blink A PCB?

It measures 119 × 92 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Blink A use?

164 parts, built around the CH340C, AD8397AR, TMP112AIDRLR(UMW) and SN74LVC1G14DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Blink A KiCad files?

From the fluffy/blinky repository on GitHub, at the commit this page was made from: the board is hardware/blink_A/blink_A.kicad_pcb and its schematic hardware/blink_A/blink_A.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Blink A design in my own project?

Its repository states no licence, so its author keeps all rights: ask fluffy before reusing the design.