

Rpi cpld
- Size
- 65 × 56.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 93
- Nets
- 107
- Pads
- 391
- Tracks, vias
- 820, 54
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Jan 2019
- Updated
- 25 Oct 2019
Overview
Rpi cpld is an open-source printed circuit board by fedor2018, from the fedor2018/RPi-CNC-HAT repository on GitHub. It is a 2-layer board of 65 × 56.5 mm with 93 parts on 107 nets, routed with 820 tracks and 54 vias.
It is built around the EPM570T100C3, LM1117-3.3 and BC817. Its parts include 44 resistors, 10 capacitors, 10 transistors, 9 connectors and 7 ICs. It belongs with the fPGA and programmable logic boards and the FPGA and CPLD boards of this library.
Main components
3EPM570T100C3
TQFP-100(14x14)0℃~+85℃ 2.5V、3.3V 440 5.4ns 570 570 76 In-system programming MAX II Supports hot swap TQFP-100(14x14) Programmable Logic Device (CPLDs/FPGAs)Intel/AlteraProgrammable Logic Device (CPLDs/FPGAs)LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedBC817
SOT-231 NPN 100nA 150MHz 300mW 40 45V 500mA 5V 700mV NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
README
README.mdRPi CNC HAT
PCB
- schematic
- fabrication
- soldering
- jtag over network
- external clk
CPLD
- verilog modules
- quartus compile
- debug
Linuxcnc driver
- spi
- rpi clk
- compile
- debug
Linuxcnc GUI
- hal
- ini
- schematic
- pyvcp panel
Parts
93| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 1k | Capacitors_SMD:C_0603_HandSoldering | R9, R10, R11, R12, R13, R14, R20, R21, R22, R23, R38, R39, R40, R41, R42, R43 |
| 10 | BC817 | TO_SOT_Packages_SMD:SOT-23 | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10 |
| 8 | 0.1 | Capacitors_SMD:C_0603_HandSoldering | C2, C4, C5, C6, C7, C8, C9, C10 |
| 8 | 200 | Capacitors_SMD:C_0603_HandSoldering | R24, R25, R26, R27, R28, R29, R30, R31 |
| 7 | 1k | Resistors_SMD:R_0603_HandSoldering | R18, R19, R33, R34, R35, R36, R37 |
| 5 | 1k | Resistors_SMD:R_0805_HandSoldering | R5, R6, R7, R8, R15 |
| 5 | PC817 | Housings_DIP:DIP-4_W7.62mm | U3, U4, U5, U6, U7 |
| 4 | MountingHole:MountingHole_2.7mm_Pad | MK1, MK2, MK3, MK4 | |
| 4 | 10k | Capacitors_SMD:C_0603_HandSoldering | R1, R2, R3, R4 |
| 2 | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J6, J9 | |
| 2 | 0 | Resistors_SMD:R_0603_HandSoldering | R16, R17 |
| 2 | 0 | Capacitors_SMD:C_0603_HandSoldering | R32, R44 |
| 2 | LED-RED0603 | LEDs:LED_0603_HandSoldering | D1, D2 |
| 2 | PinHeader_1x08_P2.54mm_Vertical | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | REF01, REF02 |
| 1 | Connectors_JST:JST_EH_B08B-EH-A_08x2.50mm_Straight | J3 | |
| 1 | 10.0 | Capacitors_SMD:C_0805_HandSoldering | C3 |
| 1 | 10u | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | CLK ext | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | CONN_02 | Connectors_Molex:Molex_KK-6410-02_02x2.54mm_Straight | J1 |
| 1 | Conn_01x10 | Connectors_JST:JST_EH_B06B-EH-A_06x2.50mm_Straight | J8 |
| 1 | Conn_01x10 | Connectors_JST:JST_EH_B08B-EH-A_08x2.50mm_Straight | J4 |
| 1 | EPM570T100 | Housings_QFP:LQFP-100_14x14mm_Pitch0.5mm | U2 |
| 1 | I2C | Connectors:1X04 | J7 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | LOGO | schematic:logo_rpi | G*** |
| 1 | LOGO | schematic:logo_emc2 | G*** |
| 1 | OSCILLATORSMD-7X5-4PAD | Clocks:OSCILLATOR-SMD-7X5-4PAD | Y1 |
| 1 | PinHeader_2x04_P2.54mm_Vertical | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | REF00 |
| 1 | RPi_Hat-rescue_RPi_GPIO | hat-design-lib:hat-PIN_ARRAY_20X2 | J2 |
| 1 | UART | Connectors:1X04 | J5 |
Similar boards
- 2 layers100 × 100 mm

- 2 layers37.3 × 59.2 mm

MCN003R3
RWeick/NDS-Codebreaker
The full schematic, gerbers, and flash rom dump of the Nintendo DS Codebreaker
19 parts3GPL-3.0 - 2 layers87 × 47 mm

- 2 layers100.2 × 116.5 mm

- 2 layers82 × 82 mm

- 2 layers37 × 90 mm

- 2 layers28 × 48 mm

E meter hardware
www-ShapeLabs-de/sgm4_to_mqtt
ESP8266 electricity meter reading head for SGM-C4 meter with homeassistant mqtt-discovery
34 parts3MIT - 2 layers100 × 40 mm

Wled controller
embediver/atx-wled-controller
A ESP-07 based controller to use with WLED and ATX power supplies.
45 parts1
Questions
How big is the Rpi cpld PCB?
It measures 65 × 56.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rpi cpld use?
93 parts, built around the EPM570T100C3, LM1117-3.3 and BC817. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rpi cpld KiCad files?
From the fedor2018/RPi-CNC-HAT repository on GitHub, at the commit this page was made from: the board is CPLD/schematic3/rpi_cpld.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rpi cpld design in my own project?
Its repository states no licence, so its author keeps all rights: ask fedor2018 before reusing the design.