Skip to the content
4 layers50 × 73 mmBio robots, the printed circuit board in 3D

Biorobitics for team E: smart ant swarm robots inspired from Formica

Size
50 × 73 mm
Copper layers
4
Thickness
1.6 mm
Parts
107
Nets
89
Pads
343
Tracks, vias
526, 277
Pours
12
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
20 Feb 2025
Updated
17 May 2025

Overview

Bio robots is an open-source printed circuit board by Fayeinstainy, from the Fayeinstainy/BIR25_TEAM_E repository on GitHub. It is a 4-layer board of 50 × 73 mm with 107 parts on 89 nets, routed with 526 tracks and 277 vias.

It is built around the TSOP38238, BQ25173DSG and ICM-20948, with the TS360ILS_R1_00001, TPH11006NL,LQ and IR333C among its other parts. Its parts include 33 resistors, 16 capacitors, 13 ICs, 8 diodes and 7 transistors. It belongs with the robots and motor control boards and the RP2040 boards of this library.

Main components

7

README

README.md

Smart Swarmica - A Swarm Ant Robots Project

Overview

This project is part of a biologically-inspired swarm robot system, where multiple robots cooperate to perform tasks such as locating a wireless charger and coordinating actions using IR signals. All circuities were initially developed and tested on a Raspberry Pi Pico, and later finalized on a custom PCB using RP2035 microcontroller chip for integration into the final robot design. The video for the whole development process and final demonstration can be found via this link: https://www.youtube.com/watch?v=agExd-AKbOk

Hardware Component

  • IR LED: IR333

  • IR Receiver: TSOP38238

  • Microcontroller: RP2350-based Raspberry Pi Pico 2W

  • Other: Resistors, Transistors (for LED driving), 38kHz signal source (via PWM)

System Architecture

final_robot_sys_architecture

Power System Architecture (Normal Operation Mode)

new_robot_power_architecture

Software Architecture

Software_algorithm drawio-2

Motor Control

Navigation

Infrared Communication

  • Uses modulated IR signals at 38kHz for one-way signaling between robots.
  • Encodes simple messages (e.g. "Relative location is (4, 12)", "Stop Moving").
  • Receiver uses TSOP382 to detect incoming signals reliably even in ambient light.

How it works:

  1. IR LED emits 38kHz modulated pulses.
  2. TSOP382 detects signal and triggers logic in firmware.
  3. Signal interpreted as communication or wall proximity.

PCB Design

Designed using kiCAD 9.0, project files, schematic and PCB pdfs under bio_robots/ folder, featuring the following features:

  • Populated: Common anode RGB LED, 3-pairs of IR transmitters and receivers, full bridge rectifier, parallel chargers for the supercapacitors, OR controller.
  • Unpopulated: ICM-20948, 1.8V regulator, level shifters, bypass strategy (U12, D10-D13)

Obstacle Avoidance

  • Based on detecting reflection of IR signal from nearby obstacles.
  • If TSOP382 receives the robot’s own IR pulses reflected from a wall, it triggers a "wall detected" event.

WI-FI Programming Mode

Parts

107
QtyValueFootprintReferences
6110Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR1, R2, R3, R13, R14, R15
4100nCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC1, C2, C4, C9
41uCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC3, C8, C15, C16
4DNP SM5817PL-TPfootprints:CR_5817PL-TP_MCC-MD10, D11, D12, D13
4TPH11006NL,LQfootprints:TPH11006NLLQQ9, Q10, Q11, Q12
30RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR18, R29, R30
3100nCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC10, C11, C12
310kResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR17, R31, R32
3330Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR8, R11, R12
3470Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR5, R6, R7
3IR333CLED_THT:LED_D5.0mm_IRGreyD1, D2, D3
3MMBT3906Package_TO_SOT_SMD:SOT-23Q1, Q2, Q3
3TSOP38238OptoDevice:TSOP38238U2, U3, U7
20Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR33, R34
2100FCapacitor_THT:100f_CPhorizontal_Radial_D10.0mm_P5.00mmC6, C7
2150kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR22, R24
2390Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR19, R20
2420kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR25, R28
2560kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR21, R23
268kResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR26, R27
274LVC1T45DW-7footprints:SOT65P210X110-6NU10, U11
2BQ25173DSGPackage_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mmU5, U6
2DNPCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC13, C14
2Motor_DCMotors:mod_motor_v2_VZ6SC0B0060081M1, M2
2MountingHole_2.7mm_M2.5_DIN965MountingHole:MountingHole_2.7mm_M2.5_DIN965MH1, MH2
2RResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR9, R10
110k DNPResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR4
122u 10V GRM21BZ71A226ME15LCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC5
13V3TestPoint:TestPoint_Pad_D1.0mmTP17
1ADC0TestPoint:TestPoint_Pad_D1.0mmTP22
1ADC1TestPoint:TestPoint_Pad_D1.0mmTP23
1ADC2TestPoint:TestPoint_Pad_D1.0mmTP21
1DCTestPoint:TestPoint_Pad_D1.0mmTP7
1GNDTestPoint:TestPoint_Pad_D1.0mmTP8
1ICM-20948Sensor_Motion:InvenSense_QFN-24_3x3mm_P0.4mmU8
1LED_GBARLED_THT:LED_D5.0mm-4_RGB_Wide_PinsD9
1LM66200DRLRfootprints:SOTFL50P160X60-8NU4
1LOGOfootprints:uos_logo_11x11G***
1LOGOfootprints:uos_logo_long32x7G***
1LOGOfootprints:qr_code14G***
1LOGOfootprints:uos_logo_long18G***
1M1+TestPoint:TestPoint_Pad_D1.0mmTP13
1M1-TestPoint:TestPoint_Pad_D1.0mmTP15
1M2+TestPoint:TestPoint_Pad_D1.0mmTP14
1M2-TestPoint:TestPoint_Pad_D1.0mmTP16
1N_PG1TestPoint:TestPoint_Pad_D1.0mmTP24
1N_PG2TestPoint:TestPoint_Pad_D1.0mmTP25
1PICO_INTestPoint:TestPoint_Pad_D1.0mmTP18
1POWER IN +TestPoint:TestPoint_Bridge_Pitch5.08mm_Drill1.3mmTP4
1POWER IN -TestPoint:TestPoint_Bridge_Pitch5.08mm_Drill1.3mmTP5
1PWM1TestPoint:TestPoint_Pad_D1.0mmTP19
1PWM2TestPoint:TestPoint_Pad_D1.0mmTP20
1RaspberryPi_PicoModule:mod_RaspberryPi_Pico_Common_THTU13
1STAT1TestPoint:TestPoint_Pad_D1.0mmTP11
1STAT2TestPoint:TestPoint_Pad_D1.0mmTP12
1SUPERCAP1TestPoint:TestPoint_Pad_D1.0mmTP9
1SUPERCAP2TestPoint:TestPoint_Pad_D1.0mmTP10
1TB6612FNGPackage_SO:SSOP-24_5.3x8.2mm_P0.65mmU1
1TLV73318PDBVRfootprints:DBV0005A_NU9
1TS360ILS_R1_00001footprints:SOP400P650X145-4NU12
1TestPointTestPoint:TestPoint_Pad_D1.0mmTP6

Similar boards

  • 2 layers400 × 40 mmPTL RAIL, the printed circuit board in 3D

    PTL RAIL

    mayoogh-flexli/Meesho-Put-To-Light

    Modular, daisy-chained 5-node IR emitter/receiver rail for the Meesho put-to-light system. Each 400 mm board has five bin positions on an 84 mm pitch.

    147 parts
  • 4 layers65 × 52.5 mmTemperatureSensor, the printed circuit board in 3D

    TemperatureSensor

    PolygonHJ/xihe

    Xihe is a self-sustaining, ultra-low-power sensing platform designed for long-lifetime deployments with zero maintenance.

    79 parts2
  • 2 layers162.3 × 64.3 mmWingnote, the printed circuit board in 3D

    Wingnote

    TinyTinfoil/wingnote-pcb

    82 parts
  • 2 layers40 × 60 mmAmulet, the printed circuit board in 3D

    Amulet

    aykevl/things

    Collection of microcontroller projects

    17 parts81
  • 2 layers35.4 × 35.4 mmDCDC, the printed circuit board in 3D

    DCDC

    Tomoshibi-technology/MovingDisplay3-Circuit

    145 parts
  • 2 layers95 × 72 mmMotordriver, the printed circuit board in 3D

    Motordriver

    Tomoshibi-technology/Tomoshibi_Circuit

    燈のプロダクト達を動かしている基板開発用リポジトリ

    151 partsMIT

Questions

How big is the Bio robots PCB?

It measures 50 × 73 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Bio robots use?

107 parts, built around the TSOP38238, BQ25173DSG, ICM-20948 and TS360ILS_R1_00001. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Bio robots KiCad files?

From the Fayeinstainy/BIR25_TEAM_E repository on GitHub, at the commit this page was made from: the board is bio_robots/bio_robots.kicad_pcb and its schematic bio_robots/bio_robots.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Bio robots design in my own project?

Its repository states no licence, so its author keeps all rights: ask Fayeinstainy before reusing the design.