

HagiwoDualVCARev2
using decoupling caps specified in this verified build: https://github.com/Testbild-synth/HAGIWO055dualvca Hagiwo uses 47uF and 1uF decoupling caps plus extra 1uF on TL074 rails Verified build uses 10uF and 100n
- Size
- 40.3 × 106 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 45
- Pads
- 168
- Tracks, vias
- 336, 29
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 27 Jul 2024
- Updated
- 1 Dec 2024
Overview
HagiwoDualVCARev2 is an open-source printed circuit board by fablabnk, from the fablabnk/HagiwoDualVCA repository on GitHub. It is a 2-layer board of 40.3 × 106 mm with 50 parts on 45 nets, routed with 336 tracks and 29 vias.
It is built around the V2164M. Its parts include 19 resistors, 12 capacitors, 6 connectors and 2 ICs.
Main components
1README
README.mdToDo
-
Add branding/info
-
Double check schematic one more time
-
DONE: Drill out holes under jacks and don't route traces through them
-
power stripe check
-
pass DRC fully
-
Double check VCA chip pinout is correct
-
Does it matter than the sleeve in pin 2 not 3?
-
Chose to simplify decoupling cap choices to one set of 1uF caps - if I don't have specified caps then go with verified caps below
-
100pF = 101 disc cap - have it
-
1uF = 105 disc cap - have it
-
470pF = 471 disc cap - have it
Key points
- Both designs are 8HP
- V2164 can be replaced with SSI2164, SSM2164, or AS2164. (I think, unverified)
- Needs calibration
Decoupling caps
using decoupling caps specified in this verified build: https://github.com/Testbild-synth/HAGIWO_055_dual_vca Hagiwo uses 47uF and 1uF decoupling caps plus extra 1uF on TL074 rails Verified build uses 10uF and 100n
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R5, R6, R15, R16 |
| 4 | 100pF | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P7.50mm_Horizontal | C1, C2, C5, C6 |
| 4 | 10k LIN | Library:Pot_9mm_DShaft_RemovedPins4_5 | RV1, RV5, RV9, RV10 |
| 4 | 1uF | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P7.50mm_Horizontal | C9, C10, C11, C12 |
| 4 | 470 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R13, R14, R17, R18 |
| 2 | 150k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R11, R12 |
| 2 | 2.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9, R10 |
| 2 | 22k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R8 |
| 2 | 33k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R7 |
| 2 | 470pF | Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P7.50mm_Horizontal | C3, C4 |
| 2 | 47uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C7, C8 |
| 2 | 50k LIN | Library:Pot_9mm_DShaft_RemovedPins4_5 | RV2, RV6 |
| 1 | 100k LIN 1 | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV3 |
| 1 | 100k LIN 2 | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV7 |
| 1 | 10K LIN 1 | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV4 |
| 1 | 10K LIN 2 | Potentiometer_THT:Potentiometer_Bourns_3296W_Vertical | RV8 |
| 1 | 7.5k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R19 |
| 1 | CV 1 | Library:EighthInch_PJ398SM_3mmNPTH | J1 |
| 1 | CV 2 | Library:EighthInch_PJ398SM_3mmNPTH | J2 |
| 1 | Eurorack_Power_10pin_Unshrouded | Library:IDC-Header_2x05_P2.54mm_Vertical_Euro_Power_Striped_ThickerText | PWR1 |
| 1 | IN 1 | Library:EighthInch_PJ398SM_3mmNPTH | J3 |
| 1 | IN 2 | Library:EighthInch_PJ398SM_3mmNPTH | J4 |
| 1 | OUT 1 | Library:EighthInch_PJ398SM_3mmNPTH | J5 |
| 1 | OUT 2 | Library:EighthInch_PJ398SM_3mmNPTH | J6 |
| 1 | TL074 | Package_DIP:DIP-14_W7.62mm_Socket | U2 |
| 1 | V2164M | Package_DIP:DIP-16_W7.62mm_Socket | U1 |
Similar boards
- 2 layers80.8 × 110 mm

- 2 layers187.2 × 26.6 mm

- 2 layers45.7 × 25.9 mm

- 2 layers21 × 31.5 mm

- 2 layers42 × 32.5 mm

Lipoboard
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
50 parts915 - 2 layers80 × 109.5 mm

NucDeck Right Controller PCB - Rev 1.2
dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!
50 parts561CERN-OHL-S-2.0 - 2 layers101 × 31.5 mm

- 2 layers123.9 × 94.4 mm

Questions
How big is the HagiwoDualVCARev2 PCB?
It measures 40.3 × 106 mm and has 2 copper layers, 1.6 mm thick.
What parts does the HagiwoDualVCARev2 use?
50 parts, built around the V2164M. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the HagiwoDualVCARev2 KiCad files?
From the fablabnk/HagiwoDualVCA repository on GitHub, at the commit this page was made from: the board is HagiwoDualVCARev2.kicad_pcb and its schematic HagiwoDualVCARev2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the HagiwoDualVCARev2 design in my own project?
Its repository states no licence, so its author keeps all rights: ask fablabnk before reusing the design.