2 layers271.8 × 114.3 mm
Ardumower mega shield svn
Ardumower/ardumower
Develop an open source robotic lawn mower (HW+SW reference platform)
426 parts282
2 layers
Illustrabot2 IF Motor Beagle v2
FablabLannion/IllustraBot222nd IllustraBot
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 79
- Nets
- 81
- Pads
- 353
- Tracks, vias
- 1,127, 0
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 9 Jan 2014
- Updated
- 13 Oct 2014
Overview
Illustrabot2 IF Motor Beagle v2 is an open-source printed circuit board by FablabLannion, from the FablabLannion/IllustraBot2 repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board with 79 parts on 81 nets, routed with 1,127 tracks and 0 vias.
It is built around the JUMPER3. Its parts include 24 resistors, 20 capacitors, 16 connectors, 6 ICs and 6 diodes. It belongs with the robots and motor control boards of this library.
Main components
1README
README.mdIllustraBot2
This is a Fablab Lannion project. Purpose is to control a robotic arm over 4G using movments from an android phone.
You can find more info on the wiki
List of directories :
- DOC : documentation (datasheets, ...)
- Kicad : electronic scheme
- android : well, android application
- beaglebone : soft running on the arm control platform
test
Parts
79| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | CONN_4 | bornier4 | P1, P2, P3, P4, P5, P6, P7, P10, P11, P12 |
| 8 | 10uF | C1 | C3, C4, C15, C16, C17, C18, C19, C20 |
| 6 | 100nF | C1 | C5, C6, C9, C10, C13, C14 |
| 6 | 100uF | CP4 | C1, C2, C7, C8, C11, C12 |
| 6 | 10kohm | R3 | R1, R2, R3, R4, R10, R12 |
| 6 | 150ohm | R3 | R5, R7, R9, R13, R15, R17 |
| 6 | 47k | R3 | R19, R20, R21, R22, R23, R24 |
| 6 | 82kohm | R3 | R6, R8, R11, R14, R16, R18 |
| 6 | LED | LED-3MM | D1, D2, D3, D4, D5, D6 |
| 6 | NPN | TO92 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 6 | STEPSTICK | Stepstick_footprint | U1, U2, U3, U4, U5, U6 |
| 4 | CONN_1 | 1pin | P13, P14, P15, P16 |
| 2 | CONN_23X2 | SIL-2x23-v1 | P8, P9 |
| 1 | JUMPER3 | SIL-3 | JP1 |
Questions
What parts does the Illustrabot2 IF Motor Beagle v2 use?
79 parts, built around the JUMPER3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Illustrabot2 IF Motor Beagle v2 KiCad files?
From the FablabLannion/IllustraBot2 repository on GitHub, at the commit this page was made from: the board is Kicad/V2/Illustrabot2_IF_Motor_Beagle_v2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Illustrabot2 IF Motor Beagle v2 design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers49 × 49 mm
OSBMS Balancer Rev 0.9
Teslafly/Dead-OpenBMS-dead
A scalable, open source battery management system
76 parts248 - 4 layers137 × 86 mm
- 2 layers100 × 90 mm
- 2 layers59.2 × 41 mm
- 2 layers86 × 54 mm
- 2 layers54.4 × 43.2 mm
- 2 layers146.1 × 53.3 mm
Watersens
whitebox-labs/tentacle
An arduino shield to host and individually isolate up to 4 Atlas Scientific sensor circuits. Measure pH, conductivity, dissolved oxygen, ORP, temperature
77 parts32