Skip to the content
2 layers54.3 × 41.9 mmRgbpong, the printed circuit board in 3D

RGB modification for AY-3-8500 based game consoles

Size
54.3 × 41.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
20
Nets
24
Pads
67
Tracks, vias
80, 10
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
9 May 2019
Updated
12 Oct 2025

Overview

Rgbpong is an open-source printed circuit board by exrom, from the exrom/rgbpong repository on GitHub. It is a 2-layer board of 54.3 × 41.9 mm with 20 parts on 24 nets, routed with 80 tracks and 10 vias.

It is built around the BC547. Its parts include 10 resistors, 1 capacitor and 1 diode.

Main components

1

README

README.md

RGB modification for AY-3-8500 based game consoles

Problems without an rgb output

The AY-3-8500 is an integrated circuit from the 1970's used in pong-like video gaming consoles. These consoles have an antenna output where the video signal is modulated onto a VHF channel. The video quality is very poor because of the nature of a composite video and the VHF back and forth conversion.

Some consoles have a colored output where the playing field, the ball and the left and right paddle have different colors. This is possible because the AY-3-8500 provides separate signals for them. A curcuit of logic gates generates different phased color carriers and combies each picture signal with one of them in order to get the colored output. The color generation is very simple and the resulting composite video signal might not be completely compatible with the standards. A wrong adjusted color carrier frequency might also lead to a TV not showing the colors at all and fall back to a b/w video.

Now there are modifications for having a composite video output for such consoles like this one. Though this already provides better video quality as the HF conversion is skipped, the quality and stability of the video is still not perfect.

Composite video signals have - in contrast to rgb - a systematic problem: luminance and color signals disturb each other. Aka dot crawl.

In my case, i got a UNIVERSUM Multi Color Spiel 4106 with PAL color output and wanted to connect it to a modern flat screen TV which did not show the colors correctly. You might also use this rgb mod to add colored output if your console is just black/white.

The RGB modification

AY-3 signals

The AY-3-8500 has this pinout:

pinout.

It works with 6...7V. In my case a voltage regulator will limit battery voltage to 6.1V.

We need to connect to these pins:

signalpin
Vss (ground)2
Sound output3
Vcc (6.1V)4
Ball output6
Right player output9
Left player output10
Sync output16
Score and Field output24

All signals are active high (high voltage == bright).

Color mapping

I decided to map the four signals to the red, green, blue inputs like this:

ballscore & fieldleftright
🔴 redxxx
🟢 greenxxx
🔵 bluexxx
--------------------------------------------------------
color⚪ white🟡 yellow🟣 purple😱 sky blue

(there is no unicode char for sky blue - sorry)

SCART signals

I decided to interface to a SCART connector which provides rgb input on a TV - at least in europe.

signalpinremark
red video150.7 Vpp, 75 ohms
green video110.7 Vpp, 75 ohms
blue video70.7 Vpp, 75 ohms
RGB video selection160..0.4V=composite, 1..3V=RGB
composite video201 Vpp, 75 ohms
audio input2+60.40 mVrms, > 47K ohms
GND signals 14, 7,18,5,9,13

Circuit

The AY-3-8500 signals are TTL (more precisely the supply voltage of AY - may be 6..9V). The 74HC4075 (3-input OR gates) does the color mapping and can work directly with the AY signals. Output current of 74HC is too weak to drive a 75Ohms video out so we need to amplify. A npn transistor is used as emitter follower to amplify the current (not the voltage). After T1-T3, we have VCC-0,7V. Video out has 1V max. After T4 we need 0...0.3V for sync levels.

The audio signal is actually not needed when the console itself has a built-in speaker. Anyway it is fun to hear how the picture processing delays audio on a modern flat TV. Note that lightguns work only on 50/60Hz crt TVs, not on modern ones. The circuit provies a jumper for audio on/off.

The composite video is needed on the SCART connector for sync even if it may be present in the rgb signals. A TV takes extracts sync information from the composite video pin. If pin 16 is 1..3V the rgb input is selected and any picture information on pin 19 is ignored. I originally tried to re-use the already present composite signal which is generated inside the game console. But this signal turned out to generate unstable picture on some TVs as it is very high resistive and grabbing it may influence internal signal leves too much. Anyhow, if the sync info is taken directly from AY, we do not use any other signal from the console which means, one can actually build up the whole game system just with the AY and some paddles/switches.

When only signals from the AY are taken, one can make such a intermediate socket which can be inserted into the console without soldering. socket

And here is the schematic

schematic

The 1kOhms R7 pull up is needed because the consoles internal circuitry loads the AY's ball pin too much the resulting level the 74HC did not recognize as low.

For T1,T2,T3 almost any bipolar npn type should do the job. Note: A BC547 has pin out C-B-E but on the board the C is in the middle. It just was easier to route. You need to cross the pins.

The schematic and the board are available for KiCAD 8.0 (thanks to just-some-tall-bloke) and EAGLE.

Photos

Original console's video signal quality with just the composite mod (quality of the antenna signal is even worse). One can see the dot crawl and some background noise.

before

After the rgb mod

after

board

board

Good luck

I like to know when you build this rgb mod, please drop me a mail. Also any other feedback is welcome.

Greetings go to my very good friend Sven.

Happy retro gaming!

other retro game projects

Siemens BILDMEISTER Turnier FZ 2001 video modification

Parts

20
QtyValueFootprintReferences
4BC547rgbpong:TO92-ECBT1, T2, T3, T4
3470rgbpong:0207_10R1, R2, R3
21k5rgbpong:0207_10R5, R10
10rgbpong:MA08-1SV3
10rgbpong:MA07-1SV1
10rgbpong:JP1JP1
11rgbpong:0207_15R8
1100µrgbpong:E2,5-5C1
1150rgbpong:0207_10R11
11krgbpong:0207_15R7
1330rgbpong:0207_10R4
15k6rgbpong:0207_10R9
1744075Nrgbpong:DIL14V1
1rotrgbpong:LED3MMLED1

Similar boards

  • 2 layers83.3 × 65.3 mmSimonShield, the printed circuit board in 3D

    SimonShield

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    46 parts14kMIT
  • 2 layers56 × 65 mmSeaTalk1, the printed circuit board in 3D

    SeaTalk1

    dotnet/iot

    This repo includes .NET Core implementations for various IoT boards, chips, displays and PCBs.

    24 parts2.4kMIT
  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342
  • 2 layers99.1 × 99.7 mmRC6502 General Video Adapter, the printed circuit board in 3D

    RC6502 General Video Adapter

    tebl/RC6502-Apple-1-Replica

    An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

    80 parts193GPL-3.0
  • 2 layers55.9 × 38.6 mmMega Amp, the printed circuit board in 3D

    Mega Amp

    theacodes/genesynth

    A Sega Genesis inspired synthesizer

    40 parts178Apache-2.0
  • 2 layers40 × 100 mmBack pcb, the printed circuit board in 3D

    Back pcb

    ZeroPhone/ZeroPhone-PCBs

    PCB files for ZeroPhone - for gerbers and schematics, go to "Releases" tab!

    118 parts148GPL-3.0
  • 2 layers100 × 100 mmCANBuster, the printed circuit board in 3D

    CANBuster

    GBert/misc

    miscellaneous stuff / unsorted

    182 parts99

Questions

How big is the Rgbpong PCB?

It measures 54.3 × 41.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rgbpong use?

20 parts, built around the BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rgbpong KiCad files?

From the exrom/rgbpong repository on GitHub, at the commit this page was made from: the board is kicad/rgbpong.kicad_pcb and its schematic kicad/rgbpong.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rgbpong design in my own project?

Its repository states no licence, so its author keeps all rights: ask exrom before reusing the design.