Skip to the content
2 layers80 × 60 mmEink weather station, the printed circuit board in 3D

Battery powered ESP32 e-paper weather station. KiCad, 2-layer, two board revisions.

Size
80 × 60 mm
Copper layers
2
Thickness
1.6 mm
Parts
35
Nets
52
Pads
177
Tracks, vias
237, 49
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
15 Sep 2026
Updated
15 Sep 2026

Overview

Eink weather station is an open-source printed circuit board by EthanGreenhouse, from the EthanGreenhouse/eink-weather-station repository on GitHub. It is a 2-layer board of 80 × 60 mm with 35 parts on 52 nets, routed with 237 tracks and 49 vias.

It is built around the ESP32-WROOM-32E-N8, AP2112K-3.3 and TP4056-42-ESOP8. Its parts include 9 capacitors, 9 resistors, 4 connectors, 3 ICs and 2 diodes. It belongs with the lEDs and displays and home automation and IoT boards and the ESP32 boards of this library.

Main components

3

README

README.md

E-Ink Weather Station

A battery-powered ESP32-WROOM-32 board that pulls weather data over WiFi and renders it on a Waveshare 4.2" four-colour e-paper panel. KiCad 10, two layers, 80 × 60 mm.

Status: Rev B.2 design frozen 2026-08-21, cleared for fabrication. Not yet built.


Design

MCUESP32-WROOM-32
DisplayWaveshare 4.2" e-Paper (G), 400 × 300, 4-colour, SPI
Power inUSB-C → TP4056 single-cell LiPo charger, 500 mA
RegulatorAP2112K-3.3 LDO
Battery2000 mAh LiPo with integrated protection, JST PH 2.0
Board80 × 60 mm, 2-layer, 35 components, 52 nets, 49 vias
Assembly27 SMD (all front side) + 2 THT connectors

Power tree:

text
USB-C (J1) → VIN 5 V → TP4056 (U2) → VSYS 3.0-4.2 V → AP2112K (U3) → +3V3 → ESP32 (U1)
                                          │
                                          └── 1M/1M divider → IO34 (ADC1_CH6) battery sense

Revision history

Rev A — 48.5 × 57.5 mm, 23 components, fully routed, and would not have run on a battery. Two blocking problems:

  1. AMS1117-3.3 regulator. ~1.1 V typical dropout (1.3 V max) and ~5 mA quiescent. On a cell spanning 4.2 V down to 3.0 V the 3.3 V rail would have sat at ~2.9 V best case and ~2.0 V worst, against the ESP32's 3.0 V minimum. The 5 mA Iq alone flattens 2000 mAh in about two weeks.
  2. Antenna keep-out routed through. The ESP32 module sat mid-board, so its keep-out carved a 48 × 21 mm bare strip (~37% of board area) and six SPI signals plus two ground stitching traces ran straight through it.

Rev B.1 — regulator swapped to AP2112K-3.3 (250 mV typ dropout at 600 mA, 55 µA Iq), module moved to the board edge so the keep-out falls off-board, board re-laid out.

Rev B.2 — final. Changes from B.1:

  • Added the LDO output capacitor (10 µF). B.1's nearest +3V3 cap was 28.94 mm from VOUT, leaving the regulator driving ~55 mm of unbypassed trace — a loop-stability risk. Now 2.34 mm.
  • Added 3 fiducials (scalene triangle, so the placement machine resolves rotation as well as position) and 3 × M3 mounting holes.
  • Load-share FET dropped after re-analysis: at ~0.7% duty cycle and ~100 µA baseline the load is ~500× below the TP4056's 50 mA termination threshold, so charge termination works as-is.

Power budget

Estimated, not measured:

  • Active: 24 wakes/day × ~0.45 mAh (5 s WiFi + 21 s panel refresh) ≈ 11 mAh/day
  • Sleep: ≈ 2.4 mAh/day
  • Total ≈ 13 mAh/day → ~4 months on 2000 mAh with ~85% usable before LDO dropout

The AP2112K's 55 µA quiescent is the largest sleep contributor — larger than the ESP32's own ~10 µA deep sleep. That's the lever if runtime ever needs extending.

Known trade-offs

  • Ground-plane slotting. 25 track segments route on B.Cu, cutting the board's only pour; six nets change layers without a stitching via within 3 mm. Worst case is 28.6% reference coverage on the display chip-select net over 50.8 mm. This is a radiated-emissions concern, not a functional one, and is accepted because the board isn't seeking certification.
  • No VBUS TVS. VIN carries 10 µF at the connector and the USB data lines are unconnected. Candidate if revisited: SMF5.0A (LCSC C19077497).
  • No reverse-polarity protection on the battery connector. See the bring-up checklist.
  • LDO dropout (~3.55 V) is above the pack's protection cutoff (~2.4–3.0 V). The ESP32 browns out before protection engages; the PCM is a last-resort net, not part of normal operation.

Firmware constraint

Disable WiFi before starting a panel refresh. ESP32 TX peaks near 500 mA against the LDO's 600 mA rating; serialising the two removes any headroom question.

Bring-up checklist

  1. Meter J2 polarity before connecting a battery. JST PH pigtails are not consistently wired and there is no reverse-polarity protection — reversed, the cell feeds −3.7 V into both the charger's BAT pin and the LDO input.
  2. Power from USB only (no battery, no display) and confirm 3.3 V at the display header.
  3. Measure sleep current against the ~13 mAh/day estimate.
  4. Isolate the display module's level translator draw — it's permanently powered from the header with no way to shut it off. If it costs tens of µA, a Rev C load switch pays for itself.
  5. Confirm charge terminates (CHRG LED extinguishes) under a normal deep-sleep duty cycle.

Repository layout

text
rev-b2/           current design — schematic, PCB, gerbers, BOM, CPL
  fab/            gerbers
  datasheets/     TP4056, AP2112, ESP32-WROOM-32E
  design-review-rev-B.2-FROZEN.md

Tools

KiCad 10.0. Fabrication targeted at JLCPCB standard tier — 0 DFM violations (min track 0.25 mm, min spacing 0.416 mm, min drill 0.3 mm, min annular ring 0.15 mm).

Parts

35
QtyValueFootprintReferences
510uFCapacitor_SMD:C_0805_2012MetricC2, C4, C7, C8, C9
3100nFCapacitor_SMD:C_0603_1608MetricC1, C5, C6
3FiducialFiducial:Fiducial_1mm_Mask2mmFID1, FID2, FID3
3MountingHoleMountingHole:MountingHole_3.2mm_M3H1, H2, H3
210kResistor_SMD:R_0603_1608MetricR3, R6
21MResistor_SMD:R_0603_1608MetricR7, R8
21kResistor_SMD:R_0603_1608MetricR4, R5
25.1kResistor_SMD:R_0603_1608MetricR1, R2
2RED LEDLED_SMD:LED_0805_2012MetricD1, D2
12.4kResistor_SMD:R_0603_1608MetricR9
147uFCapacitor_SMD:C_0805_2012MetricC3
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U3
1BOOTLibrary:SW_TS-1187ASW2
1Conn_01x02Connector_JST:JST_PH_B2B-PH-SM4-TB_1x02-1MP_P2.00mm_VerticalJ2
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ4
1ESP32-WROOM-32E-N8RF_Module:ESP32-WROOM-32U1
1RESETLibrary:SW_TS-1187ASW1
1TP4056-42-ESOP8Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalViasU2
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J1

Similar boards

  • 2 layers0.5 × 31.1 mmEnvinode, the printed circuit board in 3D

    Envinode

    aneeshlingala/FirstResponderSystem

    reverie hacks submission

    14 parts
  • 2 layers51.1 × 95 mmTalk e, the printed circuit board in 3D

    Talk e

    milovanpms/talk-e

    📻 — A simple LoRa-based talkie-walkie built on ESP32, operating on the 433 MHz frequency band for long-range, low-power wireless communication.

    75 parts4
  • 4 layers75 × 56.4 mmEsp32-c6-wroom1 board, the printed circuit board in 3D

    Esp32-c6-wroom1 board

    pushtiujeniya/esp32-c6-environmental-logger

    This repository contains an Environmental Sensor Station and Data Logger powered by the ESP32-C6-WROOM-1 microcontroller.

    59 parts4
  • 2 layers100 × 64.5 mmPCB mc, the printed circuit board in 3D

    PCB mc

    KLIMUG/Media-controller

    Компактный портативный медиаконтроллер на ESP32-S3 с механическими кнопками и Bluetooth.

    33 parts3
  • 2 layers84 × 98 mmFalloutbadge, the printed circuit board in 3D

    Falloutbadge

    sophiayduan/badges

    hackathon pcb badges

    93 parts3Unlicense
  • 2 layers500 × 137.8 mmKeyboard, the printed circuit board in 3D

    Keyboard

    ImNoahDev/MacPad-Keyboard

    The MacPad is a full sized keyboard designed for use with a Mac. The keyboard has 2 rotary encoders and a single fader for custom controls. The keyboard is designed to be used with QMK,

    354 parts2
  • 2 layers80.4 × 120 mmNext Gen MacroPad, the printed circuit board in 3D

    Next Gen MacroPad

    DevX-Dragon/Next-Gen-MacroPad

    This is a integrated macropad with all an programmable SoC

    85 parts1
  • 2 layers186 × 132 mmEvereader, the printed circuit board in 3D

    Evereader

    Ezekiel0108/Evereader

    A small and portable dual screen e-reader

    74 parts1MIT

Questions

How big is the Eink weather station PCB?

It measures 80 × 60 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Eink weather station use?

35 parts, built around the ESP32-WROOM-32E-N8, AP2112K-3.3 and TP4056-42-ESOP8. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Eink weather station KiCad files?

From the EthanGreenhouse/eink-weather-station repository on GitHub, at the commit this page was made from: the board is einkWeatherStation.kicad_pcb and its schematic einkWeatherStation.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Eink weather station design in my own project?

Its repository states no licence, so its author keeps all rights: ask EthanGreenhouse before reusing the design.