Skip to the content
2 layers77.5 × 15.7 mmBuck converter, the printed circuit board in 3D

12 V to 5 V asynchronous buck converter, 3 A at 150 kHz. 91.3% efficiency in LTspice.

Size
77.5 × 15.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
7
Nets
6
Pads
29
Tracks, vias
30, 6
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
15 Sep 2026
Updated
15 Sep 2026

Overview

Buck converter is an open-source printed circuit board by EthanGreenhouse, from the EthanGreenhouse/buck-converter repository on GitHub. It is a 2-layer board of 77.5 × 15.7 mm with 7 parts on 6 nets, routed with 30 tracks and 6 vias.

It is built around the LM2596S-5.0. Its parts include 2 capacitors, 2 connectors, 1 IC, 1 diode and 1 inductor. It belongs with the power boards of this library.

Main components

1

README

README.md

12 V to 5 V Buck Converter

A switching regulator board: 12 V in on a barrel jack, 5 V out on a USB-A socket, 3 A load target. KiCad, two layers, 78 × 16 mm.

Status: Schematic and layout complete. Not fabricated, not brought up — every figure below is a design value, not a measurement.


Why a switcher

A linear regulator doing 12 V → 5 V at 3 A dissipates (12 − 5) × 3 = 21 W in the package, which is uncoolable on a board this size and caps efficiency around 42%. A buck converter stores that energy in an inductor and delivers it to the load instead, running in the region of 80% efficient.

The trade is that a switcher is a layout problem as much as a schematic problem — every choice below is either about keeping inductor current continuous or keeping the high-current loops short.

Design

RefPartNotes
U1LM2596S-5, TO-263-5Fixed 5 V step-down, 150 kHz, 3 A rated
L133 µH radialSized from the LM2596 selection curves for 12 V in at 3 A
C1680 µFInput bulk — a buck draws input current in pulses, supplied locally
C2220 µFOutput — absorbs inductor ripple, sets load-step transient response
D1SS54, 40 V 5 A SchottkyCatch diode; carries inductor current during switch-off
J1Barrel jack12 V in
J2USB-A5 V out

The passives are sized to hold continuous conduction at the full 3 A load. Discontinuous operation isn't dangerous, but it makes output voltage load-dependent and worsens ripple.

Schottky rather than silicon for D1: lower forward drop and fast recovery, with 40 V / 5 A leaving headroom above the 12 V input and 3 A load for switching transients.

Layout

  • Input, switch node, and output traces widened to 0.8 mm for 3 A.
  • The switch node — the junction of U1's output pin, L1, and D1 — swings the full input voltage at 150 kHz. Kept short it's a trace; let it sprawl and it's an antenna.
  • The 78 × 16 mm outline is deliberately long and narrow so J1 and J2 sit at opposite ends, giving a straight-through power path with the switching section in the middle.

To verify at bring-up

  1. Switch node waveform on a scope — clean edges, no excessive ringing.
  2. Output ripple at full 3 A load.
  3. Efficiency across the load range against the ~80% the datasheet implies.
  4. U1 case temperature at sustained 3 A.

Tools

KiCad.

Parts

7
QtyValueFootprintReferences
1220uFCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC2
133uHInductor_THT:L_Radial_D12.0mm_P6.00mm_Murata_1900RL1
1680uFCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC1
1Barrel_JackConnector_BarrelJack:BarrelJack_HorizontalJ1
1DDiode_SMD:D_0805_2012MetricD1
1LM2596S-5Package_TO_SOT_SMD:TO-263-5_TabPin3U1
1USB_AConnector_USB:USB_A_Molex_48037-2200_HorizontalJ2

Similar boards

  • 4 layers95 × 95 mmCube motherboard, the printed circuit board in 3D

    Cube motherboard

    willem-pennings/balancing-cube

    A cube that balances itself in a corner or edge using reaction wheels

    52 parts1.1kGPL-3.0
  • 2 layers100 × 100 mmHydromisc, the printed circuit board in 3D

    Hydromisc

    hydromisc/hydromisc

    Open hardware to measure EC and pH, drive pumps, and otherwise manage a mid-size hydroponic grow over Wi-Fi.

    179 parts526
  • 2 layers100 × 68 mmSI4684 SMD, the printed circuit board in 3D

    SI4684 SMD

    PE5PVB/SI4684-DAB-Receiver

    SI4684 ESP32 DAB Receiver

    91 parts135GPL-3.0
  • 2 layers76.1 × 85 mmFlypi, the printed circuit board in 3D

    Flypi

    amchagas/Flypi

    This is the repository for the flypi project

    45 parts88GPL-2.0
  • 2 layers156.8 × 67.3 mmYM2151 STM32 VGM, the printed circuit board in 3D

    YM2151 STM32 VGM

    AidanHockey5/YM2151_VGM_STM32

    A hardware arcade video game music player based on the STM32 platform driving a YM2151

    52 parts81AGPL-3.0
  • 6 layers249.4 × 111.5 mmMxm immobilizer, the printed circuit board in 3D

    Mxm immobilizer

    a-little-wifi/mxm-immobilizer

    MXM to PCIe adapter

    419 parts75
  • 4 layers100 × 49.8 mmExpansion board, the printed circuit board in 3D

    Expansion board

    reubenstr/zuko

    A quadruped robot dog!

    75 parts51MIT
  • 2 layers89.2 × 103.5 mmOas, the printed circuit board in 3D

    Oas

    hubertciebiada/open-ambient-sensor

    OAS — Open Ambient Sensor: DIY multi-sensor indoor environmental monitor (CO2, PM, VOC/NOx, temperature/humidity, mmWave presence) on ESP32-C6 with ESPHome / Home Assistant integration

    64 parts44GPL-3.0

Questions

How big is the Buck converter PCB?

It measures 77.5 × 15.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Buck converter use?

7 parts, built around the LM2596S-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Buck converter KiCad files?

From the EthanGreenhouse/buck-converter repository on GitHub, at the commit this page was made from: the board is buckConverter.kicad_pcb and its schematic buckConverter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Buck converter design in my own project?

Its repository states no licence, so its author keeps all rights: ask EthanGreenhouse before reusing the design.