
Worst keyboard ever
xunker/worst_keyboard_ever
It's a mechanical keyboard made from limit switches. It has QMK firmware, it's worse than you think, but better than you expect.

Mouse hardware is an open-source printed circuit board by ertjy, from the ertjy/PMW3360-mouse-hardware repository on GitHub. It is a 4-layer board of 51 × 82 mm with 50 parts on 69 nets, routed with 472 tracks and 95 vias.
It is built around the PMW3360DM-T2QU, ADP150AUJZ-2.0-R7 and AP2112K-3.3TRG1, with the D2F-FL among its other parts. Its parts include 21 capacitors, 12 resistors, 5 switches, 4 ICs and 2 diodes. It belongs with the STM32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3, C4, C7, C8, C9, C12, C13, C14, C15, C16, C21 |
| 7 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R2, R3, R4, R5, R9, R11 |
| 5 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C5, C6, C19 |
| 3 | D2F-FL | D2F-FL:D2FFL | S1, S2, S3 |
| 3 | MountingHole_Pad | Hole:Hole_1.8mm_1.2mm | H1, H2, H3 |
| 2 | 20pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C11 |
| 2 | 4.7uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C17, C20 |
| 2 | 70R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7 |
| 2 | Conn_01x04_Pin | PinHeader:PinHeader_1x04_P2.54mm_Horizontal | J1, J2 |
| 2 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 2 | SW_Push | 147873-1:1478731 | SW1, SW2 |
| 1 | 1.5K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C18 |
| 1 | 39R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10 |
| 1 | 8MHz | Crystal:Crystal_SMD_HC49-SD_HandSoldering | Y1 |
| 1 | ADP150AUJZ-2.0-R7 | SOT95P280X100-5N:SOT95P280X100-5N | IC1 |
| 1 | AP2112K-3.3TRG1 | SOT95P282X130-5N:SOT95P282X130-5N | IC2 |
| 1 | PMW3360DM-T2QU | PMW3360DM:PMW3360 | U2 |
| 1 | STM32F103RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |

xunker/worst_keyboard_ever
It's a mechanical keyboard made from limit switches. It has QMK firmware, it's worse than you think, but better than you expect.

ntindle/trackball
Ultimate Mouse: fully custom trackball with a free-spinning active ball (capacitive touch ring, nRF52810, inductive charging) and a dual-PMW3360 base (nRF52840, USB-C, HID + custom driver). No mechanical wheel.

ndxw/RemmyMouse
Remmy uses PJRC's USB mouse library found here, modified to support five mouse buttons.


Bastardkb/charybdis-pmw-3360-sensor-pcb
A PCB for the PMW3360 sensor. Designed for the Charybdis keyboard, can be used in other projects.

great-houk/mouse-project
Contains all the relevant folders for the entire custom mouse project


It measures 51 × 82 mm and has 4 copper layers, 1.5 mm thick.
50 parts, built around the PMW3360DM-T2QU, ADP150AUJZ-2.0-R7, AP2112K-3.3TRG1 and D2F-FL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ertjy/PMW3360-mouse-hardware repository on GitHub, at the commit this page was made from: the board is mouse_hardware.kicad_pcb and its schematic mouse_hardware.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ertjy before reusing the design.