

Bramble
Bramble: Precision Agriculture Mesh
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 74
- Nets
- 103
- Pads
- 329
- Tracks, vias
- 1,250, 61
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 18 Jun 2025
- Updated
- 2 Aug 2026
Overview
Bramble is an open-source printed circuit board by erikbeerepoot, from the erikbeerepoot/bramble repository on GitHub. It is a 2-layer board with 74 parts on 103 nets, routed with 1,250 tracks and 61 vias.
It is built around the MT25QL01GBBB8ESF-0SIT, W25Q16JVSSIQ and RFM95W-915S2, with the 1N4148W and DMN3300U among its other parts. Its parts include 24 capacitors, 23 resistors, 8 ICs, 6 connectors and 3 diodes. It belongs with the RP2040 and STM32 boards of this library.
Main components
5MT25QL01GBBB8ESF-0SIT
SOIC-16-300mil-40℃~+85℃ 1.8ms 100,000 cycles 133MHz 1Gbit 2.7V~3.6V 20 Years Hardware write protection、Software write protection、Write enable latch SPI SO-16-300mil NOR FLASH ROHSMicron TechNOR FLASHW25Q16JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 10uA 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHRFM95W-915S2
LCC-16_16X16mmLCC-16_16X16mm New Arrivals ROHSHopeRF Micro-electronicsUncategorised1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching DiodesDMN3300U
SOT-23-55℃~+150℃ 1 N-channel 150mΩ@4.5V 193pF 1V 2A 30V 700mW SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETs
README
README.mdBramble
LoRa sensor and actuator network for farm monitoring, built on RP2040.
Hub-and-spoke architecture: a central hub manages the network while nodes collect sensor data (temperature, humidity) and control actuators (irrigation valves). LoRa provides long-range wireless with reliable delivery guarantees.
Hardware
- Adafruit Feather RP2040 LoRa (SX1276, 915 MHz)
- MT25QL01GBBB 128MB external flash for sensor data storage
- STM32L010 PMU for power management and sleep
Building
Requires the Pico SDK. CMake is bundled at ~/.pico-sdk/cmake/v3.31.5/bin/cmake.
# Build a specific variant
cmake -B build -DHARDWARE_VARIANT=SENSOR
cmake --build build -j8
# Variants: SENSOR, IRRIGATION, CONTROLLER, HUB, GENERIC, ALLEach variant produces a named executable (e.g. bramble_sensor.uf2).
# Run tests
cmake -B build -DBUILD_TESTS=ON
cmake --build build -j8Flashing
Hold BOOTSEL and connect via USB, then copy the .uf2 file. Or use OpenOCD with a debug probe:
~/.pico-sdk/openocd/0.12.0+dev/openocd \
-s ~/.pico-sdk/openocd/0.12.0+dev/scripts \
-f interface/cmsis-dap.cfg -f target/rp2040.cfg \
-c "adapter speed 5000" \
-c "program build/bramble_sensor.elf verify reset exit"Architecture
[Sensor Nodes] --LoRa--> [Hub/Pico] --Serial--> [Raspberry Pi] --REST--> [Dashboard]
| |
128MB Flash DuckDB
(local buffer) (long-term storage)Firmware (src/)
modes/- Application modes per hardware variant (sensor, irrigation, hub, etc.)lora/- SX1276 driver, message protocol, reliable delivery, routinghal/- Hardware abstraction (flash, NeoPixel, valves, SPI)storage/- 128MB circular flash buffer for sensor recordsconfig/- Persistent node/hub configuration
API (api/)
Flask REST API on the Raspberry Pi. Receives sensor data from the hub over serial, stores in DuckDB.
cd api && uv sync && uv run app.pyDashboard (dashboard/)
React SPA for viewing sensor data, managing nodes, and organizing zones.
cd dashboard && npm install && npm run devSetup
After cloning:
./setup.sh # configures git hooksSee CLAUDE.md for development guidelines and PLAN.md for the roadmap.
Parts
74| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C7, C11, C12, C15, C17, C18, C19 |
| 7 | 1uF | Capacitor_SMD:C_0805_2012Metric | C10, C13, C14, C16, C20, C23, C24 |
| 4 | 10K | Resistor_SMD:R_0805_2012Metric | R12, R15, R16, R21 |
| 4 | 1k | Resistor_SMD:R_0805_2012Metric | R3, R5, R8, R13 |
| 4 | MOUNTINGHOLE2.5 | MountingHole:MountingHole_2.5mm_Pad | U$1, U$2, U$3, U$4 |
| 3 | 100nF | Capacitor_SMD:C_0805_2012Metric | C4, C5, C6 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R2, R7, R11 |
| 2 | 100 | Resistor_SMD:R_0805_2012Metric | R1, R4 |
| 2 | 10pF | Capacitor_SMD:C_0805_2012Metric | C21, C22 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 150 | Resistor_SMD:R_0805_2012Metric | R22, R23 |
| 2 | 22 ohm | Resistor_SMD:R_0805_2012Metric | R17, R18 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric | C8, C9 |
| 2 | 5.1K | Resistor_SMD:R_0805_2012Metric | R19, R20 |
| 1 | 0.1 | Resistor_THT:R_Axial_DIN0414_L11.9mm_D4.5mm_P15.24mm_Horizontal | R6 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R14 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D3 |
| 1 | 20k | Resistor_SMD:R_0805_2012Metric | R9 |
| 1 | 4.7uF | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 8.2k | Resistor_SMD:R_0805_2012Metric | R10 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_EVQP2_MiddlePushTravel_H2.5mm | SW2 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | Conn_01x03_Pin | Connector_JST:JST_XH_B3B-XH-AM_1x03_P2.50mm_Vertical | J6 |
| 1 | Conn_01x05_Pin | Connector_JST:JST_EH_B5B-EH-A_1x05_P2.50mm_Vertical | J1 |
| 1 | Conn_02x06_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J7 |
| 1 | Crystal | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | Crystal | Crystal:Crystal_SMD_Abracon_ABM3-2Pin_5.0x3.2mm_HandSoldering | Y3 |
| 1 | DMN3300U | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | LED_Dual_AKA | LED_THT:LED_D3.0mm-3 | D1 |
| 1 | MCP1700x-120xxMB | Package_TO_SOT_SMD:SOT-89-3_Handsoldering | U5 |
| 1 | MT25QL01GBBB8ESF-0SIT | Package_SO:SOP-16_4.55x10.3mm_P1.27mm | U6 |
| 1 | Opamp_Quad | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U2 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_EVQP2_MiddlePushTravel_H2.5mm | SW4 |
| 1 | RFM95W-915S2 | RF_Module:HOPERF_RFM9XW_SMD | U4 |
| 1 | RP2040_QFN56 | RP2040:RP2040-QFN-56 | IC1 |
| 1 | STM32L031F6P6TR | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U3 |
| 1 | STM_RESET | Button_Switch_SMD:SW_SPST_EVQP2_MiddlePushTravel_H2.5mm | SW1 |
| 1 | TDN_5-0910WISM | Converter_DCDC:Converter_DCDC_TRACO_TDN_5-xxxxWISM_SMD | U1 |
| 1 | U.FL | Connector_Coaxial:U.FL_Molex_MCRF_73412-0110_Vertical | J5 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4110 | J3 |
| 1 | W25Q16JVSS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U7 |
| 1 | WS2812B_SK6805_1515 | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | LED1 |
More from erikbeerepoot/bramble
4- 2 layers72.1 × 70.7 mm

- 4 layers68 × 64.3 mm

- 2 layers

- 2 layers37.3 × 42.3 mm

Similar boards
- 4 layers60 × 95 mm

Devboard
tjclement/ecsc23-badge
This repo contains the hardware designs and firmware developed for the ECSC23 hardware challenge by Curious Supplies.
147 parts10 - 4 layers51.4 × 101.8 mm

- 2 layers353.1 × 124.9 mm

- 4 layers87.6 × 84 mm

Flashover
Cherry-Blossom-Development/GreywireStudio
GreywireStudio - a combined software/hardware product
95 parts - 2 layers296.6 × 128.3 mm

- 2 layers92 × 122 mm

- 2 layers431.2 × 126.4 mm

Convertible keyboard pcb
TechnikWeber/convertible-keyboard-pcb
Convertible keyboard PCB: full-size ISO-DE & ANSI with a snap-off numpad that turns it into a TKL (RP2040, USB-C, KiCad). Cheap, clean, modern core to build on — looking for a case designer.
504 parts - 2 layers306 × 125 mm

KBoard
YakshithK/KBoard
An 84-key custom mechanical keyboard built from scratch around the RP2040. No dev module: the RP2040, flash, regulator, USB-C, crystal, and support circuitry are all on the board. Uses Cherry MX Browns.
206 parts
Questions
What parts does the Bramble use?
74 parts, built around the MT25QL01GBBB8ESF-0SIT, W25Q16JVSSIQ, RFM95W-915S2 and 1N4148W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Bramble KiCad files?
From the erikbeerepoot/bramble repository on GitHub, at the commit this page was made from: the board is schematics/bramble/bramble-backups/bramble-2025-11-22_061901/bramble.kicad_pcb and its schematic schematics/bramble-fan-control/driver.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Bramble design in my own project?
Its repository states no licence, so its author keeps all rights: ask erikbeerepoot before reusing the design.