
RFIDZapper
envido32/rfid-zapper
RFID Zapper sirve para quemar, dejando fuera de funcionamiento de forma irreversible los chips tipo RFID

RFID Zapper sirve para quemar, dejando fuera de funcionamiento de forma irreversible los chips tipo RFID
RFIDZapper is an open-source printed circuit board by envido32, from the envido32/rfid-zapper repository on GitHub. It is a 2-layer board with 37 parts on 23 nets, routed with 218 tracks and 0 vias.
It is built around the L7805 and NE555. Its parts include 10 resistors, 4 transistors, 3 capacitors, 3 ICs and 3 diodes. It belongs with the radio and wireless boards of this library.

RFID Zapper sirve para quemar, dejando fuera de funcionamiento de forma irreversible los chips tipo RFID como el que se encuentran en llaves de puertas electronicas, tarjetas de transporte público, pasaportes, boletas de voto electrónico, etc. No deja marca visible en absoluto ni emite ruido alguno.
Este dispositivo debe utilizarse SOLO con fines didácticos o de pruebas. El mal uso del mismo puede ocasionar serios daños en dispositivos electrónicos.

ATENCIÓN! Este dispositivo tiene una salida en ALTO VOLTAJE. Puede ocasionar daños en el organismo o incluso la muerte si se aplica la descarga sobre el cuerpo. Debe manipularse adecuadamente. No utilizar sin protección adecuada.

RFID Zapper es un proyecto libre realizado por Manolo Envido, basado en el diseño presentado en la serie de videos de The Post Apocalyptic Inventor.
Libre para utilizar, modificar, compartir y demás bajo los términos de la licencia CERN Open Hardware Licence v1.2.
Se trata de un circuito elevador de tensión alimentado por una batería alcalina de 9v. Este elevador carga el capacitor y luego al cerrar el segundo interruptor se descarga el capacitor a través de la antena RFID. Esto genera un pulso electromagnético que al ser captado por un chip RFID lo utilizara como alimentación. Al ser un pulso de alta intensidad (y corta duración) la energía absorbida por el chip sera más alta que la soportada por el integrado probocándole un daño irreparable de forma totalmente silenciosa e invisible.
El circuito elevador de tensión es del tipo boost alimentado por una batería alcalina de 9v. Este circuito es controlado por un PWM básico realizado con el Timer 555 y controlado por el potenciómetro, se recomienda evitar un ciclo de trabajo del PWM mayor al 50% para evitar daños a la batería. Una vez cargado el capacitor el circuito de feedback enciende el LED y desactiva el Timer 555.
Menos componentes, más compacto.

Made with KiCAD
Order in PCBWay



| Description | Part | References | Value | Footprint | Quantity Per PCB |
|---|---|---|---|---|---|
| Bornier | 2x1 | SW_SPST1 SW_SPST2 BT1 | SW_CHARGE SW_ZAP Baterry9v | Bornier | 3 |
| Switch | DPDT | SW_SPST1 SW_SPST2 | SW_CHARGE SW_ZAP | Bornier | 1 |
| Battery Cell | Baterry9v | BT1 | Alkaline 9v | Bornier | 1 |
| Timer 555 IC | NE555 | U1 | NE555 | DIP 8 W7.62mm | 1 |
| Capacitor | Ceramic | C1 | 100nF | Disc 4.3mm W1.9mm P5.00mm | 1 |
| Capacitor | Ceramic | C2 | 10nF | Disc 4.3mm W1.9mm P5.00mm | 1 |
| Capacitor | Polarised | C3 | 120uF 400v | Radial D18.0mm P7.50mm | 1 |
| LED | Generic | DL1 | Any colour | LED 3.0mm | 1 |
| Diode | Ultra Fast Recovery Rectifier | D3 | RG4 | P10.16mm | 1 |
| Diode | Generic | D1 D2 | 1N4148 | P10.16mm | 2 |
| Diode | Zenner v5.1 | DZ1 | 1N4733A | P10.16mm | 1 |
| PowerMESH MOSFET | N-CHANNEL 900V 4ohm 3.5 A | Q2 | P3NB90 FP IRF3205 | TO-220 | 1 |
| Inductor | With Iron Core | L1 | 100uH | Toroid 5x10mm | 1 |
| Small Signal Transistor | NPN 45V Vce 0.1A Ic | Q1 | BC549 | TO-92 | 1 |
| Resistor | Generic | R1 R6 | 330ohm 1/8w | L3.6mm D1.6mm P7.62mm | 2 |
| Resistor | Generic | R3 R9 | 150kohm 1/8w | L3.6mm D1.6mm P7.62mm | 2 |
| Resistor | Generic | R8 | 10Mohm 1/8w | L3.6mm D1.6mm P7.62mm | 1 |
| Potentionmeter | Trimmer | R2 | 500kohm 1/8w | POT | 1 |
Costo de los materiales total aproximado (a Septiembre 2017, argentina): 10 U$D
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 1k | Resistors_ThroughHole:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R3, R7, R10 |
| 2 | BC549 | TO_SOT_Packages_THT:TO-92_Molded_Narrow | Q1, Q3 |
| 1 | 100uF 16v | Capacitors_ThroughHole:CP_Radial_D4.0mm_P2.00mm | C2 |
| 1 | 100uH | Choke_Toroid_ThroughHole:Choke_Toroid_5x10mm_Vertical | L1 |
| 1 | 10M | Resistors_ThroughHole:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R8 |
| 1 | 10k | Resistors_ThroughHole:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R5 |
| 1 | 120uF 400v | Capacitors_ThroughHole:CP_Radial_D18.0mm_P7.50mm | C3 |
| 1 | 150k | Resistors_ThroughHole:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R9 |
| 1 | 20nF | Capacitors_ThroughHole:C_Disc_D4.3mm_W1.9mm_P5.00mm | C1 |
| 1 | 220 | Resistors_ThroughHole:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R4 |
| 1 | 2k | Potentiometers:Potentiometer_Trimmer_Bourns_3296W | R2 |
| 1 | 330 | Resistors_ThroughHole:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R6 |
| 1 | Antenna_RFID | RF_Modules:NFC_ANTENNA_40_40 | AE1 |
| 1 | Battery9v | Connect:bornier2 | BT1 |
| 1 | IRF9630G | TO_SOT_Packages_THT:TO-220_Horizontal | Q4 |
| 1 | L7805 | TO_SOT_Packages_THT:TO-220_Horizontal | U2 |
| 1 | LED | LEDs:LED_D3.0mm | D2 |
| 1 | LOGO | Graphics:high-voltaje_cu | G*** |
| 1 | LOGO | Graphics:open-source-hardware_cu | G*** |
| 1 | LOGO | Graphics:open-source-hardware | G*** |
| 1 | LOGO | Graphics:gitqrcode_cu | G*** |
| 1 | LOGO | Graphics:high-voltaje | G*** |
| 1 | LOGO | Graphics:rfidzapper_cu | G*** |
| 1 | LOGO | Graphics:gitqrcode | G*** |
| 1 | LOGO | Graphics:rfidzapper | G*** |
| 1 | NE555 | Housings_DIP:DIP-8_W7.62mm_LongPads | U1 |
| 1 | P3NB90 FP | TO_SOT_Packages_THT:TO-220_Horizontal | Q2 |
| 1 | RG4 | Diodes_ThroughHole:D_A-405_P10.16mm_Horizontal | D3 |
| 1 | SW_CHARGE | Connect:bornier2 | SW_SPST2 |
| 1 | SW_READY | Connect:bornier2 | SW_SPST1 |
| 1 | SW_ZAP | Connect:bornier2 | SW_SPST3 |
| 1 | T410 700T | TO_SOT_Packages_THT:TO-220_Horizontal | D1 |
| 1 | TL071 | Housings_DIP:DIP-8_W7.62mm_LongPads | U3 |

envido32/rfid-zapper
RFID Zapper sirve para quemar, dejando fuera de funcionamiento de forma irreversible los chips tipo RFID

profdc9/NixieClock
A Nixie clock that uses IN-14 tubes and very generic components that can be easily sourced.





leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO

DoctorWkt/CSCvon8
A crazy small 8-bit CPU built with only seventeen 7400-series chips.

nicolacimmino/PLC-14500
Retro trainer board based on the MC14500 1-bit ICU. The project is OSHW certified and a ready to assemble kit is available on Tindie.
37 parts, built around the L7805 and NE555. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the envido32/rfid-zapper repository on GitHub, at the commit this page was made from: the board is project/RFIDZapper.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask envido32 before reusing the design.