

Dspod stampp4
A family of boards for Eurorack DSP audio
- Size
- 29.7 × 41.7 mm
- Copper layers
- 4
- Thickness
- 1.53 mm
- Parts
- 27
- Nets
- 78
- Pads
- 185
- Tracks, vias
- 359, 78
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 14 Sep 2025
- Updated
- 6 Oct 2026
Overview
Dspod stampp4 is an open-source printed circuit board by emeb, from the emeb/dspod repository on GitHub, published under the MIT licence. It is a 4-layer board of 29.7 × 41.7 mm with 27 parts on 78 nets, routed with 359 tracks and 78 vias.
It is built around the G50 and NAU88C22YG. Its parts include 8 capacitors, 4 resistors, 3 ICs, 3 connectors and 1 diode. It belongs with the audio and music boards of this library.
Main components
2README
README.mddspod
dspod is a small ecosystem of audio DSP boards

The collection consists of the following hardware
- dspod_module - a motherboard / carrier that adapts the standard dspod pinout for Eurorack, including power, I/O level buffers and user interface.
- dspod_cv1800b - a daughterboard comprising a Sophgo/CVItek CV1800B Linux SoC with 64MB RAM, SD card interface, USB and GPIO + audio I/O.
- dspod_rp2350 - a daughterboard with a Raspberry Pi RP2350, 4MB flash, 8MB PSRAM, USB, GPIO and audio I/O.
- dspod_esp32s3 - a daughterboard with an ESP32 S3 processor, 4MB flash, 2MB PSRAM, USB, RF, GPIO and audio I/O.
- dspod_h7r3 - a daughterboard with an STM32H7R3V8 MCU, QSPI flash or PSRAM, USB, GPIO and audio I/O
- dspod_u3c5 - a daughterboard with an STM32U3C5RI MCU, QSPI PSRAM, USB, GPIO and audio I/O.
- dspod_up5k - a daughterboard with an iCE40UP5k FPGA, Flash, PSRAM, ADC, GPIO and audio I/O.
- dspod_stampp4 - a daughterboard with an ESP32 P4 MCU, 16MB flash, 32MB PSRAM, USB, GPIO and Audio I/O
Parts
27| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 4.7uf | Capacitor_SMD:C_0402_1005Metric | C11, C12, C20, C21, C22, C23, C24 |
| 2 | 4k7 | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | Conn_01x16 | Connector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_Vertical_SMD_Pin1Left | J4, J5 |
| 1 | 0.1uf | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | G0 | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | G1 | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | G49 | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | G50 | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | G7 | TestPoint:TestPoint_Pad_D1.0mm | TP5 |
| 1 | G8 | TestPoint:TestPoint_Pad_D1.0mm | TP6 |
| 1 | LED Green | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | M5Stack Stamp P4 | EMEB:Stamp-P4 | U1 |
| 1 | NAU88C22 | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.1x3.1mm | U4 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KMR2 | SW1 |
| 1 | Serial | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Horizontal | J2 |
| 1 | Small Avatar / Logo | EMEB:avatar_small | A1 |
| 1 | XC6222B331MR-G | Package_TO_SOT_SMD:SOT-23-5 | U2 |
More from emeb/dspod
7- 4 layers26.4 × 41.7 mm

- 2 layers68.6 × 101.6 mm

- 4 layers26.4 × 41.7 mm

- 4 layers26.4 × 41.7 mm

- 4 layers26.4 × 41.7 mm

- 4 layers26.4 × 41.7 mm

- 4 layers26.4 × 41.7 mm

Similar boards
- 6 layers43.9 × 118.2 mm

Sisu SSE-9
briskspirit/Sisu_SSE-9
Experimental six-layer LTE replacement mainboard for the Nokia 3210, built around RP2354B and Telit LE910C1-WWX.
296 parts19Unlicense - 4 layers152.4 × 63.5 mm

- 2 layers100 × 100 mm

Codec test nau88c22
Neotron-Compute/codec-test-nau88c22
A test PCB for the NAU88C22 CODEC chip
74 parts2 - 2 layers87 × 76 mm

- 6 layers45 × 108 mm

- 4 layers60 × 80 mm

- 2 layers70 × 70 mm

SensactUp4
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
147 parts4Apache-2.0 - 4 layers45 × 16.5 mm

HadesGPSDongle
pms67/HadesFCS
Complete flight control system designed from scratch. Hardware designed with KiCad.
27 parts1kBSD-3-Clause
Questions
How big is the Dspod stampp4 PCB?
It measures 29.7 × 41.7 mm and has 4 copper layers, 1.53 mm thick.
What parts does the Dspod stampp4 use?
27 parts, built around the G50 and NAU88C22YG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dspod stampp4 KiCad files?
From the emeb/dspod repository on GitHub, at the commit this page was made from: the board is dspod_stampp4/Hardware/dspod_stampp4.kicad_pcb and its schematic dspod_cv1800b/Hardware/dspod_cv1800b.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dspod stampp4 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).