

Batt switch evm
Submersible field camera and sensor instrument
- Size
- 38.5 × 31.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 34
- Nets
- 20
- Pads
- 103
- Tracks, vias
- 201, 91
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 10 Sep 2026
- Updated
- 14 Sep 2026
Overview
Batt switch evm is an open-source printed circuit board by EmbryoPhenomics, from the EmbryoPhenomics/FieldCam repository on GitHub. It is a 2-layer board of 38.5 × 31.8 mm with 34 parts on 20 nets, routed with 201 tracks and 91 vias.
It is built around the TPS2117DRL and TPS22997RYZR. Its parts include 16 capacitors, 9 connectors, 5 resistors and 4 ICs.
Main components
2README
README.mdFieldCam
A submersible field camera and sensor instrument
FieldCam is a versatile, waterproof imaging and sensing instrument, powered by consumer AA batteries and capable of long term timelapse imaging out in the field.

Some of the key specifications of this instrument are as follows:
| Component | Description |
|---|---|
| Waterproof enclosure | Acrylic tube with aluminium end caps rated to 130m depth |
| Battery | 17.1 Ah AA battery pack (~24 hrs continuous video recording). Capacity for additional 22.8 Ah AA battery pack (~30 hrs). Low power mode is > 10 years with continuous system and sensor monitoring (5 second resolution) |
| Processors | STM32 L4 microcontroller for system control and low power standby. Raspberry Pi Zero 2W for video and image capture, 32gb and 1Tb SD cards for storage respectively |
| Camera sensor | CMOS 12-megapixel (Sony IMX708) |
| Video resolution | 1080p50fps maximum. Resolution and framerate can be configured using built-in app |
| Focus | Phase Detection Autofocus (PDAF) or manual adjustable focus. Range 5cm to > 2m. |
| Camera parameters | Exposure (Auto or manual), analogue gain and auto-white balance modes can all be configured via Web App |
| Lighting | Built-in adjustable LEDs (x2) with up to 170 lm each |
| Sensors | Temperature and light built-in. Pressure, salinity, pH and O2 available with additional sensor pack |
| Configuration | Setup via Web App using smartphone or laptop, connected to the instrument’s wifi hotspot. Web App enables live streaming and config of camera sensor, viewing of system status and programming of experimental schedule. All data, including video and sensor logs can be downloaded via network file sharing when in setup mode |
| Dimensions | 70 mm x 195 mm |
Parts
34| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | Conn_01x01_Pin | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J1, J3, J4, J5, J6, J7, J8, J9 |
| 7 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C4, C5, C9, C12, C14, C15 |
| 5 | 10kR | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5 |
| 3 | 100uF | Capacitor_SMD:C_1210_3225Metric | C2, C8, C10 |
| 3 | 10uF | Capacitor_SMD:C_0805_2012Metric | C3, C7, C11 |
| 2 | INA260 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U1, U3 |
| 1 | 1000pF | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C6 |
| 1 | Conn_01x03_Socket | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J2 |
| 1 | TPS2117 | Package_TO_SOT_SMD:SOT-583-8 | U2 |
| 1 | TPS22997RYZR | jlcpcb:WQFN-HR10_RYZ_TEX | U4 |
More from EmbryoPhenomics/FieldCam
12- 4 layers39 × 119.5 mm

- 4 layers39 × 119.5 mm

- 2 layers19.3 × 46.1 mm

- 2 layers47.9 × 34.7 mm

- 2 layers20.4 × 47.9 mm

- 2 layers20.4 × 47.9 mm

- 2 layers20.4 × 47.9 mm

- 2 layers48.2 × 34.7 mm

- 2 layers35.1 × 17.6 mm

- 2 layers48.2 × 34.7 mm

- 2 layers35 × 17.6 mm

- 2 layers10 × 23.2 mm

Similar boards
- 2 layers47.2 × 45.8 mm

Heater controller rev a
manhoosbilli1/heater-controller-rev-a
Rev A of hierarchical heater controller (multi-sheet)
75 parts - 6 layers144.7 × 92.3 mm

- 4 layers61.4 × 37 mm

- 4 layers85 × 74.6 mm

GPIO HAT 2
vicharak-in/Vaaman_LVDS_GPIO_Expansion_Board
GPIO Lvds extension hat for Vicharak's Vaaman 0.1
106 parts1 - 6 layers100 × 90 mm

- 4 layers100 × 100 mm

Data logger
Conor-Dunlop/FYP_datalogger
render of the datalogger with power board (yes i know it need routed)
176 parts - 2 layers63.5 × 40.6 mm

- 4 layers29.2 × 71.9 mm

KRUPS FemtoSat
krups/RockSatX-GHOST-Hardware
Hardware files for the 2025 RockSat-X GHOST mission
38 parts
Questions
How big is the Batt switch evm PCB?
It measures 38.5 × 31.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Batt switch evm use?
34 parts, built around the TPS2117DRL and TPS22997RYZR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Batt switch evm KiCad files?
From the EmbryoPhenomics/FieldCam repository on GitHub, at the commit this page was made from: the board is electronics/batt_switch_evm/batt_switch_evm.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Batt switch evm design in my own project?
Its repository states no licence, so its author keeps all rights: ask EmbryoPhenomics before reusing the design.