

Hdmi2rgb adapter
hdmi2rgb_adapter is a simple HDMI to RGB deserializer based on TFP401 (TI)
- Size
- 54.6 × 89.5 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 55
- Nets
- 174
- Pads
- 408
- Tracks, vias
- 690, 64
- Pours
- 7
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 20 May 2022
- Updated
- 20 May 2022
Overview
Hdmi2rgb adapter is an open-source printed circuit board by embeddedboys, from the embeddedboys/hdmi2rgb_adapter repository on GitHub, published under the MIT licence. It is a 4-layer board of 54.6 × 89.5 mm with 55 parts on 174 nets, routed with 690 tracks and 64 vias.
It is built around the STM32F103C6T6A, JW5211 and TFP401PZP, with the 24LC024/P among its other parts. Its parts include 26 capacitors, 11 resistors, 8 connectors, 4 ICs and 2 switches. It belongs with the interfaces and adapters and lEDs and displays boards and the STM32 boards of this library.
Main components
4STM32F103C6T6A
LQFP-48(7x7)-40℃~+85℃ 10KB 12bit 2V~3.6V 32 Bit 32KB 37 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)JW5211
SOT-23-5-40℃~+125℃@(TJ) 1 1.2A 1.2MHz~1.8MHz 2.5V~6V 40uA 600mV~6V Adjustable Buck Buck Built-in Yes SOT-23-5 DC-DC Converters ROHSJoulWatt TechDC-DC ConvertersTFP401PZP
HTQFP-100(14x14)0℃~+70℃ HTQFP-100(14x14) Video Interface ICs ROHSTexas InstrumentsVideo Interface ICs24LC024/P
PDIP-81,000,000 cycles 2.5V~5.5V 200 Years 2Kbit 400kHz 5ms Hardware write protection function、Noise suppression function I2C PDIP-8 EEPROM ROHSMicrochip TechnologyEEPROM
README
README.mdHDMI2RGB Adapter
hdmi2rgb_adapter is a simple HDMI to RGB deserializer based on TFP401 (TI)
FAQS
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4, C5, C6, C9, C10, C11, C14, C15, C16, C17, C21 |
| 6 | 10k | Resistor_SMD:R_0805_2012Metric | R1, R2, R3, R5, R7, R8 |
| 5 | 22uF | Capacitor_SMD:C_0805_2012Metric | C1, C8, C13, C20, C24 |
| 3 | 10uF | Capacitor_SMD:C_0805_2012Metric | C7, C25, C26 |
| 3 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2, J3, J7 |
| 2 | 18pF | Capacitor_SMD:C_0805_2012Metric | C12, C19 |
| 2 | 1k | Resistor_SMD:R_0805_2012Metric | R4, R6 |
| 2 | 22pF | Capacitor_SMD:C_0805_2012Metric | C22, C23 |
| 2 | BeagleBone_Black_Header | Socket_BeagleBone_Black:Socket_BeagleBone_Black | P1, P2 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_CK_KXT3 | SW1, SW2 |
| 1 | 0.01uF | Capacitor_SMD:C_0805_2012Metric | C18 |
| 1 | 11K | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 2.2uH | Inductor_SMD:L_7.3x7.3_H4.5 | L1 |
| 1 | 24LC02 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.29x3mm | U3 |
| 1 | 330R | Resistor_SMD:R_0805_2012Metric | R9 |
| 1 | 49.9K | Resistor_SMD:R_0805_2012Metric | R10 |
| 1 | CQ-USB-C16PSMT01 | CQ-USB-C16PSMT01:SHENZHEN-CHUANGQIN-TECHNOLOGY_CQ-USB-C16PSMT01 | J6 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | Crystal 32.768KHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | Crystal 8M | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y2 |
| 1 | HDMI_A | 1827059-3:TE_1827059-3 | J4 |
| 1 | JW5211 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | STM32F103C6T6A | ul_STM32F103C6T6A:STM32F103C6T6A | U1 |
| 1 | TFP401PZP | TFP401PZP:QFP50P1600X1600X120-101N | U2 |
Similar boards
- 2 layers306.4 × 117.5 mm

- 4 layers102.5 × 62 mm

Sensor Cell with Comms
Molly-M-Laugh/Senior-Final
A collection of documentation and files for our group's final senior design project
93 parts - 4 layers75.5 × 79.3 mm

- 2 layers89.1 × 37.5 mm

Koyomi hdmi lvds
exentio/koyomi-hdmi-lvds
HDMI-LVDS adapter for Vaio P displays
44 parts11CERN-OHL-S-2.0 - 2 layers59.1 × 31.6 mm

Serial remote access esp32 c6
jalbrethsen/serial-router
That download will give you a binary file that you can install to the chip using esptool. Then to push the firmware you would run the following: Where FIRMWARE.bin is the binary MicroPython firmware you downloaded or…
19 partsMIT - 2 layers89 × 51 mm

BusinessCard
JubilantMarmot/pcc5
This is my first PCB project. It took me around 20 hours. It is a small Linux computer that is the size of a business card. Based off of Allwinner F1C200s.
39 parts - 2 layers90 × 54.5 mm

- 2 layers150 × 100 mm

New year card for fhd
xiaoyaowudi-extreme/new-year-card-for-fhd
This repository contains the design of the pcb which will be sent to fhd on the Valentine's Day.
43 parts
Questions
How big is the Hdmi2rgb adapter PCB?
It measures 54.6 × 89.5 mm and has 4 copper layers, 4.69 mm thick.
What parts does the Hdmi2rgb adapter use?
55 parts, built around the STM32F103C6T6A, JW5211, TFP401PZP and 24LC024/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hdmi2rgb adapter KiCad files?
From the embeddedboys/hdmi2rgb_adapter repository on GitHub, at the commit this page was made from: the board is hardware/project/project.kicad_pcb and its schematic hardware/project/project.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hdmi2rgb adapter design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).