
Multistepper
eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32

Code samples and ready projects based on bare-metal STM32
Stm32 is an open-source printed circuit board by eddyem, from the eddyem/stm32samples repository on GitHub. It is a 2-layer board of 75 × 77 mm with 54 parts on 47 nets, routed with 469 tracks and 43 vias.
It is built around the LM1117-3.3, USBLC6-2SC6 and DTA114Y. Its parts include 15 resistors, 15 connectors, 10 capacitors, 6 diodes and 3 ICs. It belongs with the sensors and measurement and computers and single-board computers boards and the STM32 boards of this library.
The stm32samples repository is a collection of low-level, bare-metal code examples and complete
projects for various STM32 microcontroller series (F0, F1, F3, F4, G0). It uses CMSIS header files
from modm-io/cmsis-header-stm32 for register definitions.
-flto optimisationsdeprecated/This repository is a valuable resource for learning low‑level STM32 programming without vendor libraries. It covers practical applications:
For the latest updates, check the repository on GitHub.
This repository is provided under the GNU General Public License v3 or later. Full text of the GPLv3 is available at https://www.gnu.org/licenses/gpl-3.0.html.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1 | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2, C3, C7, C8, C9, C10 |
| 7 | Conn_01x04_Female | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J1, J5, J6, J7, J8, J9, J11 |
| 6 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R6, R7, R8, R9, R10, R11 |
| 6 | LED | LED_THT:LED_D3.0mm | D1, D2, D3, D4, D5, D6 |
| 4 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2, R14, R15 |
| 4 | Conn_01x01_Female | Connector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_Vertical | J2, J4, J10, J12 |
| 2 | 12 | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C5, C6 |
| 2 | 22 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R12, R13 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 1 | 1k5 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R16 |
| 1 | 20k | my_footprints:Potentiometer | RV1 |
| 1 | 47u | Capacitor_Tantalum_SMD:CP_EIA-6032-28_Kemet-C_Pad2.25x2.35mm_HandSolder | C4 |
| 1 | 8MHz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | Boot | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | Conn_01x02_Female | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J3 |
| 1 | DTA114Y | Package_TO_SOT_SMD:SOT-323_SC-70_Handsoldering | Q1 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223 | U1 |
| 1 | Reset | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | STM32LQFP48 | Package_DIP:DIP-48_W15.24mm_Socket_LongPads | U2 |
| 1 | USART1 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | P1 |
| 1 | USART2/3 | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | P2 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6_Handsoldering | U3 |
| 1 | USB_B | Connector_USB:USB_B_OST_USB-B1HSxx_Horizontal | P3 |

eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32







eddyem/stm32samples
Code samples and ready projects based on bare-metal STM32








roybaer/usb_floppy_adapter
STM32-based USB to Floppy-Disk Drive (FDD) Adapter

eddyem/ARMsingleboard
Something for singleboard PC (Orange Pi Zero1/2 etc): I2C, SPI etc.



bamnet/village
I have a collection of 1-2 dozen Department 56 lighted Christmas houses. The default lighting solution has a big problem though: a house is either lit or not.
It measures 75 × 77 mm and has 2 copper layers, 1.6 mm thick.
54 parts, built around the LM1117-3.3, USBLC6-2SC6 and DTA114Y. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the eddyem/stm32samples repository on GitHub, at the commit this page was made from: the board is testboard/F0_F1_F3-LQFP48_testboard/stm32.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask eddyem before reusing the design.