2 layers143.5 × 45.7 mm
4 layers200.5 × 70.9 mm
Clone of same project from sourceforge
- Size
- 200.5 × 70.9 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 138
- Nets
- 142
- Pads
- 594
- Tracks, vias
- 629, 28
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 18 Mar 2014
- Updated
- 8 Aug 2023
Overview
ALL is an open-source printed circuit board by eddyem, from the eddyem/IR-controller repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 200.5 × 70.9 mm with 138 parts on 142 nets, routed with 629 tracks and 28 vias.
It is built around the ADM233LANZ, RO-1224S and L6208N, with the TLE5205-2G, IPS5451 and LM1117MPX-3.3 among its other parts. Its parts include 63 resistors, 30 capacitors, 22 connectors, 11 ICs and 3 diodes. It belongs with the STM32 boards of this library.
Main components
11
ADM233LANZ
PDIP-20-40℃~+85℃ 120Kbps 2 2 5V Transceiver Yes PDIP-20 RS232 ICs ROHSAnalog DevicesRS232 ICsRO-1224S
SIP,11.5x6mmIsolated Power ModulesYLPTEC
L6208N
PowerDIP-24-25℃~+125℃ 300mΩ PowerDIP-24 Stepper Motor Driver ROHSSTMicroelectronicsStepper Motor Driver
TLE5205-2G
TO-263-7-40℃~+150℃ 6A TO-263-7 Brushed DC Motor Drivers ROHSInfineon TechnologiesMotor Drivers
IPS5451
TO-220AB-5-40℃~+150℃ 1 25mΩ 4A 5.5V~18V Active High High Side Switch Overcurrent Protection、Over temperature protection、Latch protection、Short-Circuit Protection TO-220AB-5 Power Distribution SwitchesInfineon TechnologiesPower Distribution Switches
LM1117MPX-3.3
SOT-223-40℃~+125℃ 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-223-4 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
USBLC6-2P6
SOT-666-6-40℃~+125℃ 150nA 17V 2 3.5pF 5.25V 5A@8/20us 6V ESD IEC 61000-4-2 Unidirectional SOT-666-6 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)
RT0805BRB071KL
0805-55℃~+155℃ 125mW 150V 1kΩ Thin Film Resistor ±0.1% ±10ppm/℃ 0805 Chip Resistor - Surface Mount ROHSYAGEOChip Resistor - Surface Mount
B120-E3
DO-214AC(SMA)-65℃~+125℃ 1 Independent 1A 200uA 20V 30A 520mV@1A DO-214AC(SMA) Schottky Diodes ROHSVishay IntertechnologySchottky Diodes
BMB2A0300AN1
0805-55℃~+125℃ 1 250mA 300Ω@100MHz 500mΩ ±25% 0805 Ferrite Beads ROHSTE ConnectivityFerrite BeadsDTA114Y
--55℃~+150℃ 1 PNP 100mA 100nA 250mV 350mW 50V PNP - Bipolar (BJT)onsemiBipolar (BJT)
README
README.mdIR-controller
Clone of same project from sourceforge
Don't use files from root directory, they are obsolete!!! Current code is in directory with_opencm3.
Parts
138| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 10k | SM0603 | R13, R14, R15, R16, R17, R22, R23, R24, R26, R37, R38, R39 |
| 10 | 0.33 | SM1210 | R1.1, R1.2, R1.3, R1.4, R1.5, R2.1, R2.2, R2.3, R2.4, R2.5 |
| 10 | 1n | SM0805 | C2.1, C2.2, C2.3, C2.4, C2.5, C3.1, C3.2, C3.3, C3.4, C3.5 |
| 10 | 51k | SM0603 | R5.1, R5.2, R5.3, R5.4, R5.5, R6.1, R6.2, R6.3, R6.4, R6.5 |
| 9 | 100n | SM0805 | C7, C8, C9, C12, C14, C15, C16, C17, C18 |
| 8 | RT0805BRB071KL | SM0805 | R27, R28, R29, R30, R31, R32, R33, R34 |
| 6 | 22k | SM0603 | R3.1, R3.2, R3.3, R3.4, R3.5, R7 |
| 6 | CONN_2 | SIL-2-power | P1, P8, P9, P14, P18, P19 |
| 5 | 1.8k | SM0603 | R4.1, R4.2, R4.3, R4.4, R4.5 |
| 5 | 68n | SM0805 | C1.1, C1.2, C1.3, C1.4, C1.5 |
| 5 | CONN_4 | SIL-4-power | P2, P3, P4, P5, P6 |
| 5 | L6208N | DIP-24__300_ELL | IC2.1, IC2.2, IC2.3, IC2.4, IC2.5 |
| 3 | 15k | SM0603 | R8, R20, R21 |
| 2 | 10u | CP_5x11mm | C5, C13 |
| 2 | 22 | SM0603 | R35, R36 |
| 2 | 27p | SM0805 | C10, C11 |
| 2 | 4.7k | SM0603 | R11, R19 |
| 2 | B120-E3 | DO214 | D1, D3 |
| 2 | CONN_2 | SIL-2 | P7, P17 |
| 2 | CONN_7 | SIL-7 | P11, P16 |
| 2 | DB9 | DB9FC | J1, J2 |
| 2 | NTE2984 | TO220-3-vert | Qp1.1, Qp1.2 |
| 1 | 1.2k (II) | R7 | R25 |
| 1 | 1.5k | SM0603 | R9 |
| 1 | 100k | SM0603 | R18 |
| 1 | 100u | CP_5x11mm | C6 |
| 1 | 1M | SM0603 | R12 |
| 1 | 2200u, 40V | CP_16x25mm | C4 |
| 1 | 510 | SM0603 | R10 |
| 1 | 8MHz | hc49 | Q2 |
| 1 | ADM233L | DIP-20__300_ELL | IC1 |
| 1 | BMB2A0300AN1 | SM0805 | L1 |
| 1 | BOOT | SW_PUSH_SMALL | SW2 |
| 1 | CONN_12 | SIL-12 | P12 |
| 1 | CONN_3 | SIL-3 | K1 |
| 1 | CONN_4 | SIL-4 | P15 |
| 1 | CONN_5 | SIL-5 | P13 |
| 1 | DTA114Y | SOT323 | Q1 |
| 1 | IPS5451 | TO220-5 | U1 |
| 1 | LM1117MPX-3.3 | SOT-223 | U5 |
| 1 | PWR | LED-0805 | D2 |
| 1 | RESET | SW_PUSH_SMALL | SW1 |
| 1 | RO-1224 | SIP-4-RO | Q3 |
| 1 | STM32F103 | LQFP100_STM32 | U3 |
| 1 | TLE5205 | TO220-7-12 | U2 |
| 1 | TRD | SIL-8 | P10 |
| 1 | USB-MICRO-B | MICRO-B-USB | CON1 |
| 1 | USBLC6-2 | SOT23_6 | U4 |
Questions
How big is the ALL PCB?
It measures 200.5 × 70.9 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ALL use?
138 parts, built around the ADM233LANZ, RO-1224S, L6208N and TLE5205-2G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ALL KiCad files?
From the eddyem/IR-controller repository on GitHub, at the commit this page was made from: the board is schematic/ALL.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ALL design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
More from eddyem/IR-controller
3- 2 layers
- 2 layers32 × 58 mm
Similar boards
- 2 layers61 × 49.5 mm
- 2 layers101 × 85.1 mm
- 2 layers46 × 34 mm
- 2 layers40.5 × 74.3 mm
EMO current sense INA190
darshanram008/EMO_OBD_tool
On board diagnostic tool for Battery management system
113 parts1 - 2 layers51 × 44 mm
- 2 layers34.9 × 15.2 mm
- 2 layers65 × 56.5 mm
- 2 layers88.9 × 50.8 mm
