Skip to the content
4 layers23.5 × 24.7 mmOBD C splitter, the printed circuit board in 3D
Size
23.5 × 24.7 mm
Copper layers
4
Thickness
1 mm
Parts
16
Nets
29
Pads
109
Tracks, vias
360, 56
Pours
82
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
7 Oct 2025
Updated
27 Feb 2026

Overview

OBD C splitter is an open-source printed circuit board by dzid26, from the dzid26/OBD-C_Y_splitter repository on GitHub. It is a 4-layer board of 23.5 × 24.7 mm with 16 parts on 29 nets, routed with 360 tracks and 56 vias.

It is built around the 1N5819WS. Its parts include 3 resistors, 3 connectors and 2 diodes.

Main components

1

README

README.md

OBD-C Y-splitter

  • compact size - 2.4x2.5cm
  • possibility to add 120ohm CAN termination on CAN1 and CAN3 (note they can flip, so always terminate both)
  • for development/testing setups without a harness box, the board can mock up a relay resistance with a 200ohm resistor on sbu1 - this resistance is used for the orientation detection in OBD-C ecosystem
  • test points for sbu1 and sbu2

Arrangement:

  • Normal connections is between HarnessBox and Out (for the comma device)
  • Third port ("Panda") can be used for CAN monitoring or signal injection with a Panda
    • Sbu lines (relay or ignition) are read-only for the panda. It is blocked with diodes to prevent the panda from ever closing the relay and conflicting the main device.
  • Third port has USB 2.0 lines connected, so it can be repurposed for debugging the SOM on comma device (C3X) while connected to the harness box. If you connect this to a PC, make sure harness is powered with 5V supply.
image

Schematic:

image

Parts

16
QtyValueFootprintReferences
3SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmCAN1, CAN3, mock1
3TestPointTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmG1, Ign1, Rly1
2120Ω,Resistor_SMD:R_0603_1608MetricR1, R2
21N5819WSDiode_SMD:D_SOD-323D1, D2
1clipboard:1c70aa51-c499-4037-a639-ab1a593ddef4
1200ΩResistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolderR3
1HarnessBoxTYPE-C-SMD_C9900025773J1
1OutTYPE-C-SMD_C9900025773J3
1PandaTYPE-C-SMD_C9900025773J2

The 15 most common of 16 parts.

Similar boards

  • 2 layers26.5 × 34.4 mmPicoLoaderNSB, the printed circuit board in 3D

    PicoLoaderNSB

    makeo/PicoLoader

    A cheap and easy to install modchip for the Nintendo GameCube!

    45 parts320GPL-2.0
  • 6 layers55 × 95 mmEcho r1-rev1, the printed circuit board in 3D

    Echo r1-rev1

    amachronic/echoplayer

    Echo - Open Hardware Music Player

    154 parts281CERN-OHL-S-2.0
  • 4 layers37.1 × 37.2 mmDoorman, the printed circuit board in 3D

    Doorman

    AzonInc/Doorman

    ESP32-S3 based Intercom Gateway (TCS / Koch / Niko / Scantron / Analogue Systems)

    44 parts252GPL-3.0
  • 2 layers35.9 × 62.7 mmRp2040-memcard, the printed circuit board in 3D

    Rp2040-memcard

    sd2psx/pcb

    The PCB must be produced in 0.8mm thickness. Production files are provided under the "Releases" tab. These do not include the through-hole OLED module.

    60 parts241
  • 4 layers121.9 × 109.2 mmPlinkyblack hwmidi jacks, the printed circuit board in 3D

    Plinkyblack hwmidi jacks

    plinkysynth/plinky_public

    a public release of the plinky sw and hw

    300 parts227
  • 6 layers83.5 × 56 mmEspiff v3 1, the printed circuit board in 3D

    Espiff v3 1

    MDCservice/EsPiFF

    An ESP32 in the Raspberry Pi form factor

    172 parts223GPL-3.0
  • 6 layers90 × 153 mmBlackpants, the printed circuit board in 3D

    Blackpants

    o7-machinehum/Blackpants

    Open blackpants.kicadpro for the active A523 schematic and PCB. It replaces the A33 hierarchy and uses AXP717C + AXP323 with 2GB LPDDR4.

    300 parts189MIT
  • 2 layers53 × 53 mmHair electrolysis machine, the printed circuit board in 3D

    Hair electrolysis machine

    zoemaestra/hair-electrolysis-machine-usb-c

    A fork of scd31's hair electrolysis machine but with USB-C and optimised for cheaper assembly with JLCPCB

    83 parts168CERN-OHL-P-2.0

Questions

How big is the OBD C splitter PCB?

It measures 23.5 × 24.7 mm and has 4 copper layers, 1 mm thick.

What parts does the OBD C splitter use?

16 parts, built around the 1N5819WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the OBD C splitter KiCad files?

From the dzid26/OBD-C_Y_splitter repository on GitHub, at the commit this page was made from: the board is OBD-C-splitter.kicad_pcb and its schematic OBD-C-splitter.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the OBD C splitter design in my own project?

Its repository states no licence, so its author keeps all rights: ask dzid26 before reusing the design.