Skip to the content
2 layers20 × 20 mmLightSensorPCB, the printed circuit board in 3D

Upgrades for Traeger to add smart capability

Size
20 × 20 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
11
Pads
58
Tracks, vias
110, 29
Pours
1
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
3 Feb 2023
Updated
16 Oct 2026

Overview

LightSensorPCB is an open-source printed circuit board by dwynnychuk, from the dwynnychuk/SmartSmoker repository on GitHub. It is a 2-layer board of 20 × 20 mm with 18 parts on 11 nets, routed with 110 tracks and 29 vias.

It is built around the LTR-329ALS-01, VL53L3CXV0DH/1 and RNCP0603FTD10K0, with the CL21A475KAQNNNE, PRT-14417 and CSL1901UW1 among its other parts. Its parts include 5 capacitors, 3 ICs, 2 resistors, 1 diode and 1 connector.

Main components

6

README

README.md

Smart-Smoker

Upgrade to my existing Traeger smoker BBQ to add intelligent functionality. Initial upgrades target data acquisition to monitor internal and ambient temperatures. The second stage of this project will use integrated sensor data to drive the smoker fan, auger, and hot end with a custom PID-based controller.

How it works

Firmware and iOS application in development. The devices will tie into the wall power on the control panel inside the smoker. An iOS device will be used to connect to the system once running, which will receive updates over BLE regarding the status of the cook.

Hardware

Main PCB

  • Custom implementation of ESP32-WROOM module for WiFi and BLE connectivity
  • AC/DC rectifier with optional USB power handled with power path selector IC (LTC4412)
  • Input for 4x K-Type thermocouples to monitor food temperature (x2), external ambient temperature, and internal ambient temperature. Analog multiplexer is used to allow the use of a single amplifier.
  • Interface to connect to Lid and Hopper PCBs

Lid PCB

  • Ambient light sensor to detect if the user left the cover off after a cook
  • IMU to be used as a forward feed input for the PID controller

Hopper PCB

  • Ambient light sensor to detect if the user left the cover off after a cook
  • IMU to alert the user if the hopper lid is left open
  • ToF sensor to read remaining pellet level

Pinout

1 - I2C SDA
2 - GND
3 - I2C SCL
4 - +3.3V

Image

SmokerCad

Suggested Changes for Next Hardware REV

  • Delete 1x ambient light sensors
  • Add a dedicated GND pin for easier use of a logic analyzer
  • Breakout XSHUT and INT pins on main board for easier connection to hopper
  • Footprint change on U4
  • Add control for Traeger interface to implement PID control
  • Add jumper for I2C select on IMU(s)

Parts

18
QtyValueFootprintReferences
4TestPointTestPoint:TestPoint_Pad_D1.0mmTP1, TP2, TP3, TP4
30.1 uF 50V X7R 0603Capacitor_SMD:C_0603_1608MetricC2, C3, C5
2M3MountingHole:MountingHole_3.2mm_M3_DIN965_PadH1, H2
11 uF 25V X5R 0603Capacitor_SMD:C_0603_1608MetricC1
110kOhm 1% 0603Resistor_SMD:R_0603_1608MetricR2
14.7 uF 25V X5R 0805Capacitor_SMD:C_0805_2012MetricC4
1750Ohm 1% 0603Resistor_SMD:R_0603_1608MetricR1
1HopperCustoms Smoker:PRT-14417J1
1LSM6DSMTRCustoms:PQFN50P300X250X86-14NU2
1LTR-329ALS-01Customs:LTR-329ALS-01U1
1RED 1.8V 2mA 0603LED_SMD:LED_0603_1608MetricD1
1VL53L3CXV0DH/1Customs Smoker:XDCR_VL53L3CXV0DH_1U3

More from dwynnychuk/SmartSmoker

5
  • 4 layers60 × 80 mmDigitalPCB, the printed circuit board in 3D

    DigitalPCB

    dwynnychuk/SmartSmoker

    Upgrades for Traeger to add smart capability

    111 parts
  • 4 layers90 × 45 mmSmart Smoker PCB, the printed circuit board in 3D

    Smart Smoker PCB

    dwynnychuk/SmartSmoker

    Upgrades for Traeger to add smart capability

    80 parts
  • 2 layers60 × 100 mmAnalogPCB, the printed circuit board in 3D

    AnalogPCB

    dwynnychuk/SmartSmoker

    Upgrades for Traeger to add smart capability

    60 parts
  • 2 layers22 × 17 mmLIDPCB, the printed circuit board in 3D

    LIDPCB

    dwynnychuk/SmartSmoker

    Upgrades for Traeger to add smart capability

    10 parts
  • 2 layers60 × 100 mmAnalogPCB, the printed circuit board in 3D

    AnalogPCB

    dwynnychuk/SmartSmoker

    Upgrades for Traeger to add smart capability

    5 parts

Similar boards

  • 2 layers96.5 × 96.5 mmBionic base, the printed circuit board in 3D

    Bionic base

    tgtakaoka/retro-bionic

    Modern platform to run retro CPUs

    41 parts6
  • 4 layers46 × 30 mmCan distance sensor, the printed circuit board in 3D

    Can distance sensor

    nlbutts/can_distance_sensor

    This is a small CAN based Time-of-Flight (TOF) sensor. It determines the distance to an object and sends the resulting message on the CAN bus.

    74 partsMIT
  • 4 layers25 × 25 mmDistance, the printed circuit board in 3D

    Distance

    sean618/MakerTiles

    Modular STM32 electronic-tile system: hardware, firmware, the MicroBus + Field Protocol stack, and a Python daemon.

    20 partsMIT
  • 8 layers80 × 80 mmQsbc, the printed circuit board in 3D

    Qsbc

    qfreiman/qsbc

    Single Board Computer based on the i.MX8M Mini

    481 parts3GPL-3.0
  • 2 layers241 × 60.1 mmAdc test board, the printed circuit board in 3D

    Adc test board

    ben-e-christensen/kicad

    98 parts
  • 4 layers40 × 40 mmMinimax, the printed circuit board in 3D

    Minimax

    bradyte/minimax

    58 parts
  • 4 layers49.9 × 49.9 mmDc dc, the printed circuit board in 3D

    Dc dc

    Pejo-306/dc-dc-buck-boost

    Bachelor's degree diploma project

    28 partsMIT
  • 4 layers83.2 × 125.8 mmCrommeter, the printed circuit board in 3D

    Crommeter

    ShawnHymel/crommeter

    SHOW ME WHAT YOU GOT

    57 parts

Questions

How big is the LightSensorPCB PCB?

It measures 20 × 20 mm and has 2 copper layers, 1.6 mm thick.

What parts does the LightSensorPCB use?

18 parts, built around the LTR-329ALS-01, VL53L3CXV0DH/1, RNCP0603FTD10K0 and CL21A475KAQNNNE. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the LightSensorPCB KiCad files?

From the dwynnychuk/SmartSmoker repository on GitHub, at the commit this page was made from: the board is PCB/HOPPER PCB/LightSensorPCB.kicad_pcb and its schematic PCB/HOPPER PCB/LightSensorPCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the LightSensorPCB design in my own project?

Its repository states no licence, so its author keeps all rights: ask dwynnychuk before reusing the design.