4 layers100 × 54 mm
2 layers55 × 90.8 mm
🚀 Thrust Vector Controlled Model Rockets
- Size
- 55 × 90.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 33
- Nets
- 51
- Pads
- 133
- Tracks, vias
- 128, 0
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 23 Jul 2020
- Updated
- 8 Jul 2021
Overview
Slider is an open-source printed circuit board by DusterTheFirst, from the DusterTheFirst/rocketry repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 55 × 90.8 mm with 33 parts on 51 nets, routed with 128 tracks and 0 vias.
It is built around the BMP280, L7805CV and FM25V20A-PG, with the BNO055 and IRF540N among its other parts. Its parts include 6 resistors, 5 ICs, 5 diodes, 3 capacitors and 2 connectors. It belongs with the RP2040 and NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
5
BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure Sensors
L7805CV
TO-2200℃~+125℃@(Tj) 1 1.5A 2V@(1A) 35V 5V 68dB@(120Hz) 8mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-220 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
FM25V20A-PG
DIP-8-40℃~+85℃ 100uA 25MHz 2Mbit 2V~3.6V 300uA 3uA SPI DIP-8 FRAM ROHSInfineon TechnologiesFRAM
BNO055
LGA-28(3.8x5.2)-40℃~+85℃ 2.4V~3.6V 40uA I2C、UART IMU X,Y,Z X,Y,Z ±16g ±2000dps LGA-28(3.8x5.2) Accelerometers ROHSBosch SensortecAccelerometers
IRF540N
TO-2201 N-channel 1.35nF 100V 130W 280pF 33A 35mΩ@10V 4V 52nC@10V 85pF N-Channel TO-220 MOSFETs ROHSOSENMOSFETs
README
README.mdThrust Vector Controlled Model Rockets
This repository consists of the rockets that Zachary Kohnen has created. These rockets use active TVC based stabilization. The models for each rocket can be found in the rockets directory, and the flight firmware for each project can be found in the firmware directory. Below is a list of the rockets, basic information about them, and hyperlinks to their respective information.
You can access a development log published online at rocketry.dusterthefirst.com file.
License
Thrust Vector Controlled Model Rockets
Copyright (C) 2020 Zachary Kohnen (DusterTheFirst)
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <https://www.gnu.org/licenses/>.All content in this repository was developed and maintained by @DusterTheFirst (Zachary Kohnen). Software and firmware is licensed under the GNU GPL 3.0 license and CAD models and other artistic works are licensed under the CreativeCommons Attribution-NonCommercial-ShareAlike license
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3, R4 |
| 3 | D_Schottky | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D3, D4, D5 |
| 2 | 100uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C2, C3 |
| 2 | L7805CV | Package_TO_SOT_THT:TO-220-3_Vertical | U2, U3 |
| 2 | MountingHole | MountingHole:MountingHole_3mm | H1, H2 |
| 1 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R8 |
| 1 | 1825910-6 | digikey-footprints:Switch_Tactile_THT_6x6mm | S1 |
| 1 | 2.2k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 220k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 47uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C1 |
| 1 | ADC Ground Reference | NetTie:NetTie-2_SMD_Pad0.5mm | NT1 |
| 1 | BMP280 | adafruit:Adafruit_BMP280 | A2 |
| 1 | BNO055 | adafruit:Adafruit_BNO055 | A1 |
| 1 | Battery | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-3.5-H_1x02_P3.50mm_Horizontal | BT1 |
| 1 | FM25V20A-PG | cypress:FM25V20A | U5 |
| 1 | IRF540N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | LED (RED) | LED_THT:LED_D5.0mm | D2 |
| 1 | LED (YLO) | LED_THT:LED_D5.0mm | D1 |
| 1 | LM1086-3.3 | Package_TO_SOT_THT:TO-220-3_Vertical | U1 |
| 1 | Mini Speaker | SparkFun-Electromechanical:BUZZER-12MM | LS1 |
| 1 | Parachute | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | Pico | MCU_RaspberryPi_and_Boards:RPi_Pico_TH_Perfboard | U4 |
| 1 | SW_SPDT | digikey-footprints:Switch_Toggle_ATE1D-2M3-10-Z | SW1 |
| 1 | Servo X | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1 |
| 1 | Servo Y | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M2 |
| 1 | UC Debug PWR | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
Questions
How big is the Slider PCB?
It measures 55 × 90.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Slider use?
33 parts, built around the BMP280, L7805CV, FM25V20A-PG and BNO055. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Slider KiCad files?
From the DusterTheFirst/rocketry repository on GitHub, at the commit this page was made from: the board is rockets/slider/kicad/slider.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Slider design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 4 layers203.2 × 100.1 mm
- 4 layers60 × 60 mm
Rocket payload
Gupatron/Gupsfirstpcb
This is the first pcb that I will manufacture and intend to use for teleop usecases in my personal projects.
138 parts - 4 layers75 × 83 mm
Ember pilot version
IITB-Rocket-Team-Avionics/Ember
Experimental Flight Computer with potential mitigations of previous issues faced by FLYTE and a testbed for new systems.
65 parts4MIT - 4 layers25 × 0.3 mm
- 2 layers57.2 × 57.2 mm
- 2 layers70.9 × 45.7 mm
TVC
IbrahimEssamIbrahim/Thrust-Vector-Controlled-Rocket-Design
This project proposes the development of a Thrust Vector-Controlled (TVC) rocket as an alternative to drones for high-altitude payload delivery.
47 parts - 2 layers166 × 88.9 mm
