Skip to the content
2 layers96.5 × 78.7 mmLiftlighter, the printed circuit board in 3D

personal project for driving an old lift indicator I found

Size
96.5 × 78.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
51
Nets
44
Pads
147
Tracks, vias
139, 4
Routed
Yes
KiCad
KiCad 4
Created
27 Jan 2016
Updated
5 Dec 2017

Overview

Liftlighter is an open-source printed circuit board by dsprenkels, from the dsprenkels/liftlighter repository on GitHub, published under the MIT licence. It is a 2-layer board of 96.5 × 78.7 mm with 51 parts on 44 nets, routed with 139 tracks and 4 vias.

It is built around the LD1117S33TR(MS) and BC548. Its parts include 13 resistors, 13 connectors, 10 transistors, 6 capacitors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

LiftLighter

I once found an old lift indicator in Radboud University's Faculty of Science (credits to Luuk van Summeren). If you don't know what I mean, here is an example.

The indicator has ten lights: down, 1, 2, 3, 4, 5, B, S, K and up. This repository contains the KiCad files for the circuit board and the software for the Atmega8 microcontroller.

Components

The board (as you can see in the schematic) is reasonably modular. If you are going to build your own setup, I recommend doing so with a 3.3V power supply with LEDs instead of 12V lights.

For a breadboard-proof-of-concept:

  • 1x Atmega8 microcontroller
  • 11x LED + resistor
  • 1x 32.768kHz crystal
  • 2x 22 pF capacitors (for use with crystal)
  • 1x pull-up resistor (30-80kΩ) for reset
  • 1x control button

For a very complete setup, add:

  • 1x reset button
  • 1x switch or pin header w/ jumper for PD5.
  • 12V setup
    • 1x 3.3V voltage regulator
    • 1x 100nF capacitor (for use with voltage regulator)
    • 1x 10μF capacitor (for use with voltage regulator)
    • 10x 12V led light + transistor + resistor (instead of LEDs)
    • 1x fuse
    • 1x 3.3V backup battery
    • 1x diode (for use with backup battery)
    • 1x diode (for prevention of backflow current)
  • Pin headers (whichever amount you are going to need)

Getting started

If you are interested in this project, ask me personally about it. Although I try to keep my documentation complete and readable, I think it may be hard to get your setup correctly. Anyway, here goes:

I use a Raspberri Pi to flash my microcontrollers, for this I use a customized version of the avrdude tool which uses linuxspi (more info about this). If you have your own methods to flash your microcontrollers you can just use them. In this README I assume you will be using my method.

  1. Install KiCad (I used version 4.0.3)
  2. Install gcc-avr, avr-libc and Kevin Cuzner's avrdude tool on your Raspberri Pi.
  3. git clone https://github.com/dsprenkels/liftlighter.git
  4. cd liftlighter
  5. Wire up the microcontroller and all the components on a breadboard according to the KiCad liftlighter.sch file. I recommend tweaking the setup, using LEDs instead of 12V lights (which allows you to ditch all the transistors). Parts like the 32.768kHz crystal are important!
  6. Connect the Raspberri Pi's GPIO pins to the microcontroller (see below).
  7. make flash
  8. Send me an e-mail, because something did not work as expected.

If all went well, the Atmega8 microcontroller should now be executing the liftlighter

Wire connections

All the wiring used during the normal operation of the program can be viewed in pcb/liftlighter.sch using KiCad. Furthermore, a PCB layout can be found in pcb/liftlighter.kicad_pcb.

To flash the microcontroller, I use my Raspberri Pi and Kevin Cuzner's avrdude tool. When using this setup, you will have to connect the following (physically numbered) pins:

typePiAtmega8
Vcc177 & 2
GND208 & 22
RST221 (PC6)
MOSI1917 (PB3)
MISO2118 (PB4)
SCLK2319

You can actually use any free GPIO pin for reset, as long as you tell arvdude which one you are using in the Makefile.

make fuse calls avrdude and the Pi should immediately see the Atmega8. If it does not work, check your connections. More reading about using a Raspberri Pi to flash a microcontroller can be found on Cuzner's blog. Additionally, you may find the datasheet for the Atmega8 helpful. You can also write me an email.

Questions

Feel free to send me an email on my Github associated e-mail address.

Parts

51
QtyValueFootprintReferences
11CONN_01X02Terminal_Blocks:TerminalBlock_Pheonix_MPT-2.54mm_2polP2, P4, P5, P6, P7, P8, P9, P10, P11, P12, P13
10BC548TO_SOT_Packages_THT:TO-92_Molded_WideQ1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10
10RDiscret:R4R14, R15, R16, R17, R18, R19, R20, R21, R22, R23
3100nFCapacitors_ThroughHole:C_Disc_D6_P5C1, C5, C6
222pFCapacitors_ThroughHole:C_Disc_D6_P5C3, C4
250KDiscret:R4R1, R2
2SW_PUSHButtons_Switches_ThroughHole:SW_PUSH_SMALLSW1, SW2
110uFCapacitors_ThroughHole:C_Disc_D6_P5C2
1160Discret:R4R3
13VConnect:CR2032HBT1
1ATMEGA8-PHousings_DIP:DIP-28_W7.62mmIC1
1CONN_01X02Pin_Headers:Pin_Header_Straight_1x02P3
1CONN_01X06Pin_Headers:Pin_Header_Straight_1x06P1
1CrystalCrystals:Crystal_WatchY1
1DDiodes_ThroughHole:Diode_DO-41_SOD81_Horizontal_RM10D1
1FUSECUSTOM:FUSE_ROUNDF1
1LD1117S33TRTO_SOT_Packages_THT:TO-220_Neutral123_VerticalU1
1LEDLEDs:LED-3MMD2

Similar boards

  • 2 layers65 × 56 mmMMDVM HS Dual Hat, the printed circuit board in 3D

    MMDVM HS Dual Hat

    phl0/MMDVM_HS_Dual_Hat

    Duplex variant of MMDVM_HS_Hat

    216 parts218
  • 2 layers100 × 100 mmWifi PB panel, the printed circuit board in 3D

    Wifi PB panel

    AntonioMR/Wifi-Play-Board

    Placa de experimentacion para el ESP12F (ESP8266)

    416 parts29
  • 2 layers65 × 56 mmMMDVM RPT Hat, the printed circuit board in 3D

    MMDVM RPT Hat

    mathisschmieder/MMDVM_RPT_Hat

    MMDVM_RPT_Hat for the Raspberry Pi

    119 parts27
  • 2 layersRobot MGR, the printed circuit board in 3D

    Robot MGR

    rayvburn/diff_drive_mapping_robot

    ROS driver for the Raspberry Pi based differential drive robot

    95 parts27
  • 4 layers111.8 × 80.8 mmPrototype1, the printed circuit board in 3D

    Prototype1

    nmikstas/atari_pokey

    Recreation of the Atari POKEY chip (work in progress)

    164 parts20
  • 4 layers45.5 × 50 mmAdapter, the printed circuit board in 3D

    Adapter

    strfry/LG360VR

    This about making the LG 360 VR Goggles usable with a normal DisplayPort outlet.

    58 parts19
  • 2 layers74.9 × 40.6 mmAnavi fume extractor, the printed circuit board in 3D

    Anavi fume extractor

    AnaviTechnology/anavi-fume-extractor

    Open source WiFi development board for a portable fume extractor with 5V USB-powered fan for absorbing smoke.

    34 parts17
  • 2 layers74.9 × 40.6 mmAnavi thermometer, the printed circuit board in 3D

    Anavi thermometer

    AnaviTechnology/anavi-thermometer

    WiFi Smart Thermometer with ESP8266, DHT22, DS18B20, OLED display and slots for up to 3 I2C sensor modules

    25 parts17

Questions

How big is the Liftlighter PCB?

It measures 96.5 × 78.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Liftlighter use?

51 parts, built around the LD1117S33TR(MS) and BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Liftlighter KiCad files?

From the dsprenkels/liftlighter repository on GitHub, at the commit this page was made from: the board is pcb/liftlighter.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Liftlighter design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).