
Programmable light
dilshan/programmable-light
Simple time based programmable light controller

A small wireless BLE control puck: a knob (rotary encoder), an OLED screen, and three buttons, on a round Ø80 mm 2-layer PCB, powered by a nice!nano v2 (nRF52840) + LiPo.
Pico2-knob is an open-source printed circuit board by dsandall, from the dsandall/pico2-knob repository on GitHub. It is a 2-layer board of 51 × 99.5 mm with 29 parts on 37 nets, routed with 234 tracks and 23 vias.
It is built around the MC34063AD, DMG3415U and SS14. Its parts include 8 resistors, 6 capacitors, 3 switches, 2 ICs and 2 connectors. It belongs with the RP2350 and nRF52 and nRF5x boards of this library.
A small wireless BLE control puck: a knob (rotary encoder), an OLED screen, and three buttons, on a round Ø80 mm 2-layer PCB, powered by a nice!nano v2 (nRF52840) + LiPo.
Name is legacy — it started as an RP2350/Pico 2 board, then moved to the nice!nano for wireless. This repo is the hardware (schematic + layout), a rough mechanical mockup, and
firmware/— currently just bring-up firmware (Rust/Embassy, UF2) for the soldered board: LED heartbeat plus encoder/button events over USB serial. No screen, battery or BLE yet.
hardware/pico2-knob.kicad_pro in KiCad 10. The schematic embeds its symbols and the
board embeds its footprints, so it opens standalone; lib/marbastlib (nice!nano sym/fp) and
the project lib-tables are included so libraries resolve cleanly too.
12V_EN.| Signal | nice!nano pad |
|---|---|
| Encoder A / B / SW | P0.09 / P0.10 / P1.11 (pads 24 / 23 / 22) |
| Buttons 1 / 2 / 3 | P0.31 / P0.02 / P1.15 (pads 17 / 19 / 20) |
| OLED DC / SCLK / SDI | P0.06 / P0.08 / P0.17 (pads 1 / 2 / 5) |
| OLED RES / CS | P0.22 / P0.24 (pads 7 / 8), 10 kΩ pull-ups (R2/R6) |
| 12V_EN (panel rail) | P1.06 (pad 12), active low — R8 pulls Q1's gate to +BATT |
| Power | 3V3 (pad 16), GND, BAT+ → +BATT |
This layout was script-generated (see scripts/) and auto-routed (freerouting), then
hand-touched at the encoder. Please sanity-check freely — a few notes:
pth_inside_courtyard between
the back-side socketed nano and the front-side encoder courtyard. The nano sits ~8.5 mm
below the board on sockets, so there's no real clash — but please confirm you agree.scripts/manual_route.py) and S2's GND return is a manual trace into the south pour
(scripts/fix_s2.py).hardware/ — KiCad 10 project (schematic, PCB, lib-tables)lib/marbastlib/ — nice!nano symbol + footprint (trimmed to what's used)scripts/ — generators: gen_sch.py, gen_pcb.py, routing helpers; *.sh render/ERC/DRCcad/ — FreeCAD mechanical mockup (mockup.py) + component STEP models (step/)build/pico2-knob.pdf — quick-look: schematic + routed layout| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | SW1, SW2, SW3 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R6 |
| 1 | +12V | TestPoint:TestPoint_Pad_D1.5mm | TP4 |
| 1 | .1uF | Capacitor_SMD:C_1206_3216Metric | C6 |
| 1 | 1 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
| 1 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R8 |
| 1 | 100uH | Inductor_SMD:L_12x12mm_H6mm | L1 |
| 1 | 10uF | Capacitor_SMD:C_1206_3216Metric | C3 |
| 1 | 150 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 1M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 1k | Resistor_SMD:R_1206_3216Metric | R4 |
| 1 | 1u | Capacitor_SMD:C_1206_3216Metric | C4 |
| 1 | 22uF | Capacitor_SMD:C_1210_3225Metric | C2 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.5mm | TP3 |
| 1 | 4.7u | Capacitor_SMD:C_1206_3216Metric | C5 |
| 1 | 8.66k | Resistor_SMD:R_1206_3216Metric | R3 |
| 1 | 800pF | Capacitor_SMD:C_1206_3216Metric | C1 |
| 1 | DMG3415U | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | ER-CON20HT-1 | pico2-knob:ER-CON20HT-1 | J3 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.5mm | TP1 |
| 1 | LiPo_JST_PH | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | MC34063AD | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | RotaryEncoder_Switch | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | RE1 |
| 1 | SS14 | Diode_SMD:D_SMA | D1 |
| 1 | V_BAT | TestPoint:TestPoint_Pad_D1.5mm | TP2 |
| 1 | nice!nano_v2 | marbastlib-xp-promicroish:nice_nano_AH_Reversible | U1 |

dilshan/programmable-light
Simple time based programmable light controller



fietser28/EL-Load
The DCL8010 electronic load module features a DC Electronic Load with several modes and protections. This project is the for the development boards for this project. There is a seperate git project for the firmware.



horvathgergo/esp8266-for-uppatvind
Smart controller for IKEA Uppåtvind Air Purifiers

horvathgergo/esp8266-for-fornuftig
Smart controller for IKEA Förnuftig Air Purifiers
It measures 51 × 99.5 mm and has 2 copper layers, 1.6 mm thick.
29 parts, built around the MC34063AD, DMG3415U and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the dsandall/pico2-knob repository on GitHub, at the commit this page was made from: the board is board_pico2knob/bom/rev2-src/pico2-knob.kicad_pcb and its schematic board_pico2knob/bom/rev2-src/pico2-knob.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask dsandall before reusing the design.