Skip to the content
PCBKitNew board
2 layers44.1 × 49.5 mmFlightController, the printed circuit board in 3D

FlightController

drtrigon/eagle1

Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

Open in PCBKitView on GitHub.kicad_pcb
Size
44.1 × 49.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
9
Nets
56
Pads
108
Tracks, vias
32, 12
Pours
3
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
7 Apr 2018
Updated
17 Mar 2019

Overview

FlightController is an open-source printed circuit board by drtrigon, from the drtrigon/eagle repository on GitHub, published under the MIT licence. It is a 2-layer board of 44.1 × 49.5 mm with 9 parts on 56 nets, routed with 32 tracks and 12 vias.

It belongs with the robots and motor control boards of this library.

README

README.md

Projekte

design rule check status PCB Build Status Build Status

Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo. See there and in .travis.yml for more info.

(might make sense to split projects off into separate repos/submodules)

N64TinyUSB

projects/N64TinyUSB/N64TinyUSB_HelveTiny_1.0.brd from EDRC.me

Order: make sure to select PCB Thickness 2mm and "Gold Fingers"!

based on boxtec.ch Helvetiny 1.0 PCB design:

code/firmware (design based on attiny45 n64-usb)

Built using the attiny45 n64-usb AVR source files. Works out of the box but emulates 1 device only (that contains both controller).

https://github.com/drtrigon/sketchbook/tree/master/cli/n64dual_tiny45

Hint: Order PCB directly

Upload the GERBER files below to https://jlcpcb.com/quote and order.

Drone_MultiWii / FlightController

projects/Drone_MultiWii/FlightController.brd from EDRC.me

arduino-papilio_1-WireSniffer_Rev1

projects/arduino-papilio_1-WireSniffer_Rev1/1-Wire_Sniffer_REV1.brd from EDRC.me

DACRackUnit

projects/DACRackUnit/reference-tee-16pin.brd from EDRC.me projects/DACRackUnit/power-supply.brd from EDRC.me projects/DACRackUnit/addressing-auto.brd from EDRC.me projects/DACRackUnit/reference-tee-15pin.brd from EDRC.me projects/DACRackUnit/addressing-nand.brd from EDRC.me projects/DACRackUnit/references-no-gnd-loop.brd from EDRC.me projects/DACRackUnit/addressing-manual-gnd.brd from EDRC.me projects/DACRackUnit/high-power-supply.brd from EDRC.me

Setup

I would like to use features like CI (continous integration) keep a copy/mirror on e.g. github and more.

Maintaining a copy/mirror (more precise: with 2 remotes overloaded origin) on GitHub also allows to use GitLab and GitHub together and by that all the nice featurs on GitHub. See also; https://steveperkins.com/migrating-projects-from-github-to-gitlab/

"Option 2: Overload Origin with Both Remotes (needs one single pull/push only)"; in order to clone and set this repo up use:

text
$ git clone file://///data/mount/gvfs/smb-share:server=.../01git/eagle.git
$ cd eagle
$ git remote set-url --add origin https://github.com/drtrigon/eagle.git

you can check the settings with:

text
$ git remote -v
origin  /data/mount/gvfs/smb-share:server=.../01git/eagle.git/ (fetch)
origin  /data/mount/gvfs/smb-share:server=.../01git/eagle.git/ (push)
origin  https://github.com/drtrigon/eagle.git (push)

Enable EDRC.ME for a Repository (for Eagle)

http://www.edrc.me/docs/

Enable Travis CI for a Repository (for Eagle)

https://github.com/drtrigon/test-eagle-edrc/blob/master/.travis.yml (does not work reliably yet)

Login to Travis-CI using the GitHub account and enable Travis-CI for the given repo.

Add a .travis.yml file to your project, commit, pull/push and enjoy.

A word of caution; the travis run will at the end - if successfull - try to push the results back to this repo.

Further Info

EDRC.me: https://michaelblouin.ca/blog/2018/02/25/automate-design-rule-checks-autodesk-eagle/

gerber (travis or local python script): http://www.rocketnumbernine.com/2011/12/14/automating-gerbers-from-eagle

text
...
# create top copper (cmp), bottom copper (sol), top solder mask (stc), bottom solder mask (sts), {top} silkscreen (plc)
${EAGLE} -X -dGERBER_RS274X -o${outputfile}.cmp ${board} Top Pads Vias
${EAGLE} -X -dGERBER_RS274X -o${outputfile}.sol ${board} Bottom Pads Vias
#${EAGLE} -X -dGERBER_RS274X -o${outputfile}.mil ${board} Milling
${EAGLE} -X -dGERBER_RS274X -o${outputfile}.plc ${board} Dimension tPlace tNames
${EAGLE} -X -dGERBER_RS274X -o${outputfile}.stc ${board} tStop
${EAGLE} -X -dGERBER_RS274X -o${outputfile}.sts ${board} bStop
#${EAGLE} -X -dGERBER_RS274X -o${outputfile}.crc ${board} tCream
#${EAGLE} -X -dGERBER_RS274X -o${outputfile}.dpv ${board} Drills
#${EAGLE} -X -dGERBER_RS274X -o${outputfile}.drh ${board} Holes
...

(mill and drill needs: gerb274x-mill-drill.cam)

Generate schematic, PCB and GERBER from KiCAD (TODO)

License

The content of this project itself is licensed under the Creative Commons Attribution 3.0 license, and the underlying source code used to format and display that content is licensed under the MIT license, see the LICENSE file for license rights and limitations (MIT).

Parts

9
QtyValueFootprintReferences
2M14FlightController:1X14JP2, JP3
1CON1FlightController:MA07-1SV1
1CON2FlightController:MA09-1SV2
1CON3FlightController:MA05-1SV3
1CON5FlightController:1X12SV5
1M02FlightController:1X02JP1
1M09FlightController:1X09JP4
1NANOFlightController:NANOU$1

Questions

How big is the FlightController PCB?

It measures 44.1 × 49.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the FlightController use?

9 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the FlightController KiCad files?

From the drtrigon/eagle repository on GitHub, at the commit this page was made from: the board is projects/Drone_MultiWii/FlightController/FlightController.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the FlightController design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).

More from drtrigon/eagle

8
  • 2 layers100 × 80 mmHigh power supply, the printed circuit board in 3D

    High power supply

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    41 parts1MIT
  • 2 layers100 × 80 mmAddressing manual gnd, the printed circuit board in 3D

    Addressing manual gnd

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    37 parts1MIT
  • 2 layers100 × 80 mmAddressing nand, the printed circuit board in 3D

    Addressing nand

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    35 parts1MIT
  • 2 layers68.9 × 53.3 mm1-Wire Sniffer REV1, the printed circuit board in 3D

    1-Wire Sniffer REV1

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    34 parts1MIT
  • 2 layers100 × 80 mmPower supply, the printed circuit board in 3D

    Power supply

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    25 parts1MIT
  • 2 layers20.1 × 37.3 mmN64TinyUSB HelveTiny 1.0, the printed circuit board in 3D

    N64TinyUSB HelveTiny 1.0

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    24 parts1MIT
  • 2 layers100 × 80 mmReferences no gnd loop, the printed circuit board in 3D

    References no gnd loop

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    20 parts1MIT
  • 2 layers100 × 80 mmReference tee-15pin, the printed circuit board in 3D

    Reference tee-15pin

    drtrigon/eagle

    Results of eagle and kicad CI from travis are stored in https://github.com/drtrigon/eagle/tree/result/pcb branch and linked/shown in https://github.com/drtrigon/sketchbook repo.

    16 parts1MIT

Similar boards

  • 2 layers103 × 30.5 mmTS Back Endcap, the printed circuit board in 3D

    TS Back Endcap

    EEVengers/ThunderScope

    ThunderScope GitHub Repo

    9 parts1.3kMIT
  • 2 layers31.8 × 47.6 mmNGC 38 connector, the printed circuit board in 3D

    NGC 38 connector

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    9 parts1.2k
  • 2 layers24 × 27.3 mmExpansion Card Retrofit, the printed circuit board in 3D

    Expansion Card Retrofit

    FrameworkComputer/ExpansionCards

    Reference designs and documentation to create Expansion Cards for the Framework Laptop

    9 parts1.1kCC-BY-4.0
  • 2 layers15.6 × 17.3 mmSKR Mini TFT Thermistor Board, the printed circuit board in 3D

    SKR Mini TFT Thermistor Board

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    9 parts1.1kGPL-3.0
  • 2 layers39.1 × 49.5 mmLearnoliver, the printed circuit board in 3D

    Learnoliver

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    9 parts915
  • 2 layers17.4 × 16.9 mmToolhead, the printed circuit board in 3D

    Toolhead

    tanaes/whopping_Voron_mods

    9 parts787GPL-3.0
  • 2 layers9.8 × 108 mmExpander, the printed circuit board in 3D

    Expander

    wntrblm/Castor_and_Pollux

    A Juno-inspired dual oscillator

    9 parts587
  • 2 layersKeyboard after, the printed circuit board in 3D

    Keyboard after

    adamws/kicad-kbplacer

    KiCad plugin for automatic keyboard's key placement and routing

    9 parts547GPL-3.0